Page 2 - ii; Table of Contents
ii Table of Contents 1. Introduction ....................................................................................................... 1 Features ........................................................................................................................ 1 Package Contents ...........
Page 4 - LED Status; LED
2 LED Status LED Color Description 100Mbps Green On for 100Mbps Off of 10Mbps or not connected Link Green LAN activity. Blinking when there is data flow between LAN and the host computer.
Page 5 - Install Driver; to install the driver.
3 2. Installation Windows 7/ Vista 1. Insert the Driver CD-ROM into your CD-ROM Drive. 2. Click Run Install.exe 3. Click Install Driver to install the driver.
Page 6 - Connect the Adapter to an available USB port of your computer
4 4. Click Next . 5. Click Install . 6. Click Finish . 7. Remove the CD-ROM from your computer ’s CD-ROM drive. 8. Connect the Adapter to an available USB port of your computer 9. Drivers will install automatically 10. Connect a Network cable from the TU2-ET100 to a Switch, Router or Cable/DSL Modem...
Page 7 - Windows XP; Next
5 Windows XP 1. Insert the Driver CD-ROM into your CD-ROM Drive. 2. Click Install Driver to install the driver. 3. Click Next . 4. Click Install .
Page 8 - Finish; Connect the Adapter to an available USB port of your computer
6 5. Click Finish . 6. Remove the CD-ROM from your computer ’s CD-ROM drive. 7. Connect the Adapter to an available USB port of your computer 8. Drivers will install automatically 9. Connect a Network cable from the TU2-ET100 to a Switch, Router or Cable/DSL Modem.
Page 11 - Windows ME; Insert the provided CD into your CD-ROM drive, then Click; Specify the location of the driver
9 Windows ME 1. Insert the provided CD into your CD-ROM drive, then Click Exit. 2. Connect the Adapter to an available USB port of your computer 3. When the follow screen pop up, select Specify the location of the driver (Advanced)
Page 12 - When the screen below appears, click; Browse; to navigate to
10 4. When the screen below appears, click Browse to navigate to D:\Driver\Win98_ME where D: is your CD-ROM drive letter. Then click Next . 5. Click Next 6. Click Finish .
Page 13 - Yes; to restart your computer.
11 7. When prompted, click Yes to restart your computer. 8. Connect a Network cable from the TU2-ET100 to a Switch, Router or Cable/DSL Modem.
Page 16 - If the system prompts you for the Windows 98SE CD-ROM, click; and click; OK
14 7. If the system prompts you for the Windows 98SE CD-ROM, click OK . Remove the provided CD and insert the Windows 98SE CD-ROM. Then click OK again. 8. If the screen below appears, click OK . 9. In the drop-down list, select F:\Driver\Win98_ME and click OK .
Page 18 - Verifying the Driver Installation in Windows; To verify your Ethernet adapter installation, select
16 Verifying the Driver Installation in Windows To verify your Ethernet adapter installation, select Control Panel > System > ( Hardw are ) > Device Manager . In the Netw ork adapters group, ASIX AX88772 USB2.0 to Fast Ethernet Adapter should be displayed. If there is a question or exclamat...
Page 19 - System Preferences; and select; Network; ” to add an “; USB Ethernet
17 Mac 10.6x 1. Connect the Ethernet adapter to a free USB port. There system will pop up a message “A new network interface has been detected” 2. If the message not pop up , please Start System Preferences and select Network , then click the ” ＋ ” to add an “ USB Ethernet “ service .
Page 20 - USB Gigabit Etherne; t “ then click “; Advanced; ” to setting the network; Renew DHCP License; “to get the IP
18 3. Select “ USB Gigabit Etherne t “ then click “ Advanced ” to setting the network by static IP or thru DHCP way. 4. by “ Using DHCP” Mode , please Click” Renew DHCP License “to get the IP address , Else you have to enter the related information from your network serv ice provider .
Page 21 - GO; > to verify if your Ethernet adapter is properly installed.
19 5. You will find that a new Ethernet network interface is available 6. Once you finish the installation, you can open GO > Utilities > System Profile > Hardw ard > USB > to verify if your Ethernet adapter is properly installed.
Page 22 - Continue; to go to next step.
20 Mac 10.5x 1. Insert the provided driver CD into your CD-ROM drive. Double-click the CD and navigate to the directory of \Driver\Mac10.x . 2. In the directory of Mac10.x, please double-click AX88772_10.5 to execute the installer program. 3. The onscreen prompted and please click on Continue to go ...
Page 23 - Install; Continue Installation; to continue this installation.
21 4. Please Click on Install to continue this installation. 5. Make sure that you want to install this driver now and the computer will be restarted once the installation is done. Please click on Continue Installation to continue this installation.
Page 24 - Restart; to take the new settings effect.
22 6. Click on Restart to take the new settings effect.
Page 25 - Select a destination disk to install the driver and click
23 Mac 10.4.x 1. Insert the provided CD into your CD-ROM drive. Copy the archive file under the directory of \Driver\Mac10.4\ to the desktop and then double-click the file until you locate the setup file. 2. Double-click the setup file “ AX88772 ”. 3. When the welcome screen appears, click Continue ...
Page 26 - to start the installation.; Authenticate; screen appears, enter your password in the provided; When the software was successfully installed, click
24 5. Click Continue to start the installation. 6. When the Authenticate screen appears, enter your password in the provided field and click OK . 7. Click Continue Installation . 8. When the software was successfully installed, click Restart .
Page 27 - Configuring Network Settings and Making a Connection; figure the network settings of; Apple; icon and select
25 9. After the restart, plug the Ethernet adapter’s USB cable into an available USB port on your computer. Then attach one end of an Ethernet cable to the Ethernet port on the adapter and the other end to your network switch, hub or router. 10. Mac system will detect the new hardware and show the n...
Page 28 - figure the network; Apply Now; from the; Show; to establish a network connection.
26 2. From the Show drop-down list, select the adapter to be configured, e.g., Ethernet Adapter (en1) . Con figure the network settings as required by your network and then click Apply Now . 3. To make a connection, select Network Status from the Show drop-down list and highlight the adapter represen...
Page 32 - Extensions; folder will lead
30 You must use the command line to install the driver as instructed above. Simply copy and paste AX88772.kext to the Extensions folder will lead to an improper installation as the warning message below:
Page 33 - Hardware; 0KB SRAM for RX Packets Buffering
31 3. Specifications Hardware Standards USB 2.0, 1.1 IEEE 802.3: 10Base-T IEEE 802.3u: 100Base-TX Data Transfer Rate Ethernet: 10Mbps/20Mbps (Half/Full Duplex) Fast Ethernet: 100Mbps/200Mbps (Half/Full Duplex) Embedded Buffers 20KB SRAM for RX Packets Buffering 8KB SRAM for TX Packets Buffering Supp...
Page 34 - Limited Warranty; TU2-ET100– 3 Years Limited Warranty
32 Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TU2-ET100– 3 Years Limited Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty. If ...
