TRENDNet TPL-310AP - Manual

Page 2 - Table of Contents; English

Table of Contents Version 01.07.2011 English 1 1. Before You Start2. Configure the TPL-310AP 3 3. Create a powerline network 7 4. LEDs and Buttons 9 1 Troubleshooting 11 Wireless Tips 15

Page 3 - Before You Start; A Desktop or Laptop PC with or wireless Network Adapter Installed; Package Contents; Multi-Language Quick Installation Guide; System Requirements; Supported Operating Systems; GHz or above

1. Before You Start ŸŸ A Desktop or Laptop PC with or wireless Network Adapter Installed Ÿ Existing 10/100Mbps wired network when TPL-310AP is used to a powerline network to an existing wired network Ÿ Web Browser: Internet Explorer (6.0 or higher) ® Ÿ Additional HomePlug AV powerline adapter (e.g. ...

Page 5 - Enter

3 Note: When installing for the first time, it is required that you configure the Access Point from a wired computer. Assign a Static IP address to your computer's network adapter in the subnet of 192.168.10.x. Since the Access Point's default IP address is 192.168.10.100, make sure no other network...

Page 9 - be on the same electrical system.; Create a powerline network; Plug a TPL-303E or other TRENDnet Powerline

7 Note: 1. DO NOT install the TPL-310AP until instructed to do so.2. DO NOT plug the TPL-310AP into a surge protector or power strip.3. It is NOT recommended to use this product on electrical systems that use AFCI circuit breakers or plugged into GFI protected outlets as this may cause performance d...

Page 10 - (OPTIONAL) Connect a network cable from the; Plug the TPL-310AP into an available power; Your installation is now complete; Thank you for choosing TRENDnet

8 4. (OPTIONAL) Connect a network cable from the TPL-310AP into the network port on yourremote computer or network appliances (e.g. Game Console, IP Set box, network enabled TV, etc.). 5. Verify that the WIFI (Wireless) (Blinking/Green), ETH (Ethernet) (Green), PL (Powerline) and PWR (Power) (Solid/...

Page 11 - LEDs and Buttons

9 4. LEDs and Buttons WPS (Wi-Fi Protected Setup) ETH (Network Port) WIFI(Wireless) PWR (Power) PL (Powerline)

Page 12 - The Power switch is located at the top of the device.; Network Port; Hold for 1 second to reset power line setting; Sync

10 Note: The Network Port, WPS button, Reset button and Sync button are located at the bottom of the device. *Note: The following factors may affect the powerline network's connection quality: • Noise – Generated by appliances that are connected to your electrical system through poweroutlets that ha...

Page 13 - Troubleshooting

1. How do I configure TCP/IP settings on my computer's network adapter? Troubleshooting 11 Windows 7 Windows Vista Windows XP/2000 1. Go into the Control Panel , click Network and Internet , click Network and Sharing Center , click Change Adapter Settings and then right-click the Local Area Connecti...

Page 16 - move the switch to the on position.

14 7. After I successfully configured the Access Point to meet my network settings, I cannot connect to my network using wireless computers. If you have a DHCP server in your network, you need to go into TCP/IP settings again and re-select "Obtain an IP address automatically" to allow the PC...

Page 17 - Wireless Tips; Assign your network a unique SSID

15 Wireless Tips The following are some general wireless tips to help minimize the impact of interference within an environment. Assign your network a unique SSID Do not use anything that would be identifying like “Smith Family Network”. Choose something that you would easily identify when searching...

TRENDNet TPL-310AP - Manual

Table of Contents:

Summary

Other TRENDNet Models