Trane LS-90 - Manual
Trane LS-90 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – TOOLS; Good; REMOVE OLD UNIT; Caution
- Page 3 – What wires do you have?; Connect your wires
- Page 4 – Mount the LS-90 to wall; Wall; HVAC Set-up on screen menu
- Page 5 – Check HVAC system; (leave OFF for 4 minutes before checking COOL)
- Page 6 – After you have labeled and connected your wires,; 4VAC is Required; and then touch; Calibrate controls; CALIBRATE
- Page 7 – To use the; FOR FRESH AIR BAFFLE; WIRE REFERENCE CHART; Your Wires
- Page 8 – Zoned Systems Reference; Notes on your system
16
PG
16
Notes on your system
Customer support:877-254-5625 or www.LockStateConnect.com
1
PG
1
LS-90 Installation Guide
•
Your thermostat is a precise instrument, handle it with care.
•
Turn off electricity to the HVAC system before installing or
servicing thermostat or any part of the system.
.
d
e
t
e
l
p
m
o
c
s
i
k
r
o
w
l
i
t
n
u
n
o
k
c
a
b
y
t
i
c
i
r
t
c
e
l
e
n
r
u
t
t
o
n
o
D
•
• Do not short (jumper) across electric terminals at the control
on the furnace or air conditioner to test the system. This may
damage the thermostat.
•
All wiring must conform to local codes and ordinances.
• This thermostat is designed for use with 24 volt
AC and
millivolt systems (with a separate 24
V
AC power adapter).
• The thermostat relay load should be limited to 1.0 amp;
higher amperage may cause damage to the thermostat.
To avoid electrical shock and to prevent damage to the
furnace, air conditioner, and thermostat, disconnect the power
supply before beginning work. This can be done at the circuit
breaker, or at the HVAC system.
SAVE
ENERGY
HVAC
STATUS
MENU
NORMAL
$0.05 KW
Power Status Norm
al $.05/kW
h
HE AT
12:30pm
5/25 WED
TARGET
77
o
TEMP
HUMI D
23
%
FAN
o
F
Caution
ENGLISH
Caution
H
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 PG 2 You will need a small Phillips screwdriver and a drill with 3/16-in. (4.8mm) bit for wall mounts. Replacement installations - mount the LS-90 in place of the thermostat. You must have a “C” wire or other 24VAC power available at the LS-90 location. A new location will require moving your wiri...
4 PG 4 What wires do you have? Make sure your wires are labeled. This may require you to nd the ‘other end’ connection for each wire on your heating or air conditioning equipment and read the label there. Refer to the Wire Reference page 13 for better understanding of wire labels from different HVAC...
6 PG 6 Mount the LS-90 to wall 1. Hold the LS-90 against the wall, with the wires coming over the top above terminal block. The LS-90 will cover the hole in the wall. 2. Position LS-90 for best appearance. Use the optional stand- offs if more space for wires is needed behind the LS-90.3. Attach the ...
