Toshiba X300 - Manual

6 5.375 x 8.375 ver 2.3 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or ...

7 5.375 x 8.375 ver 2.3 Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖ The IEEE 802.11 Standard on Wireless LANs ...

8 5.375 x 8.375 ver 2.3 In some situations or environments, the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include: ❖ Using the Wireless LAN equipment on board airplanes, or ❖ In any oth...

9 5.375 x 8.375 ver 2.3 The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum sh...

10 5.375 x 8.375 ver 2.3 The European Union WEEE (Waste from Electrical and Electronic Equipment) Directive Information The European Union WEEE (Waste from Electrical and Electronic Equipment) Directive is intended to protect the quality of the environment and human health through the responsible us...

11 5.375 x 8.375 ver 2.3 However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact yo...

12 5.375 x 8.375 ver 2.3 2. Indication The indication shown below appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. OF: This equipment uses OFDM modulation. 3 The interference range of this equipment is less than 40m. 4 This equ...

13 5.375 x 8.375 ver 2.3 Radio Approvals for Wireless Devices The following information is dependent on what type of wireless device is in your computer. Not all devices are available on all models. Approved Countries/Regions for use for the Atheros AR5BXB72 2.4 + 5GHz 11n minicard This equipment is...

17 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8187B This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Albania Argentina Australia Austria Azerb...

18 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for theIntel ® PRO/Wireless 3945ABG Network Connection This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. An ad...

19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 4965AGN This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. An adhoc mode is avail...

20 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless Technology Interoperability Bluetooth ® Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ❖ Bluetooth S...

21 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from Toshiba equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. ...

22 5.375 x 8.375 ver 2.3 In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include: ❖ Using the equipment with Bluetooth wireless techno...

25 5.375 x 8.375 ver 2.3 Optical Drive Safety Instructions This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT. To use this model properly, read the user’s guide carefully and keep it for your future reference. Never attempt to disassemble, adjust or repair an optical...

27 5.375 x 8.375 ver 2.3 Trademarks Qosmio is a registered trademark of Toshiba America Information Systems, Inc. and/or Toshiba Corporation. Microsoft, Outlook, Windows, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other count...

28 5.375 x 8.375 ver 2.3 Contents Introduction................................................................................ 35 This guide ...............................................................37Safety icons ............................................................38 Other icons used ....

30 Contents 5.375 x 8.375 ver 2.3 Customizing your computer’s settings....................87Caring for your computer........................................87 Cleaning the computer ......................................88Moving the computer ........................................88Using a computer ...

32 Contents 5.375 x 8.375 ver 2.3 Surfing the Internet .........................................130Internet features..............................................130Uploading to, and downloading files from, the Internet .....................................131 Exploring audio features .................

33 Contents 5.375 x 8.375 ver 2.3 Fingerprint utility limitations ...........................157Using the Fingerprint Authentication Utility.....157Fingerprint Logon ...........................................158Care and maintenance of your fingerprint reader ...........................................

35 5.375 x 8.375 ver 2.3 Introduction Welcome to the world of powerful, portable, multimedia computing. With your Toshiba computer, your work and entertainment can accompany you wherever you go. Your Computer model may be ENERGY STAR ® compliant. If the model you purchased is compliant, it is labele...

37 Introduction This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specificatio...

38 Introduction Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the ser...

39 Introduction Other documentation 5.375 x 8.375 ver 2.3 Other documentation Your computer comes with the following documentation: ❖ An electronic version of the user’s guide (this document) ❖ It may also contain guides for other programs that may come with your system. For accessory information, v...

40 Chapter 1 Getting Started This chapter provides tips for using your computer effectively, summarizes how to connect components, and explains what to do the first time you use your computer. The “Instruction Manual for Safety and Comfort,” that is shipped with your computer, contains important saf...

41 Getting Started Selecting a place to work To keep your computer in prime operating condition, protect your work area from: ❖ Dust, moisture, and direct sunlight. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the compu...

43 Getting Started Setting up your computer Important information on your computer’s cooling fan Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. Always make sure your computer and AC adaptor have adequate ventilation and are protected from overhe...

44 Getting Started Setting up your computer Please handle your computer carefully to avoid scratching or damaging the surface. Setting up your software When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely. The names of win...

45 Getting Started Registering your computer with Toshiba Registering your computer with Toshiba Product registration is strongly recommended, and allows Toshiba to send you periodic updates, announcements, and special offers applicable to your product. Product registration can be completed by eithe...

46 Getting Started Connecting to a power source Connecting to a power source Your computer requires power to operate. Use the power cord/cable and AC adaptor to connect the computer to a live electrical outlet, or to charge the computer’s battery. Never pull on a power cord/cable to remove a plug fr...

48 Getting Started Charging the main battery ❖ Glows red when the main battery is fully charged ❖ Is unlit when the main battery has discharged, the battery is not charging, or the AC adaptor is not plugged into the computer or AC outlet ❖ Flashes amber when the main battery charge is low and it is ...

49 Getting Started Using the computer for the first time Battery life and charge time may vary depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display pa...

50 Getting Started Using the computer for the first time Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. Any small bright dots that ...

52 Getting Started Adding memory (optional) Installing a memory module Memory modules can be installed in the memory module slots on the base of the computer. You will need a small Phillips screwdriver for this procedure. If the computer has been running recently, the memory module may be hot. The s...

57 Getting Started Adding memory (optional) 14 Replace the memory module slot cover and secure it using the screw. 15 Re-insert the main battery. For more information on inserting the main battery, see “Inserting a charged battery” on page 118 . 16 Turn the computer right side up. 17 Reconnect the c...

59 Getting Started Adding memory (optional) 4 Replace the memory module slot cover and secure it using the screw. 5 Re-insert the main battery. For more information on inserting the main battery, see “Inserting a charged battery” on page 118 . 6 Turn the computer right side up. 7 Reconnect the cable...

60 Getting Started Hard Drive Recovery Utilities Hard Drive Recovery Utilities Your computer has been configured with a hard disk partition to allow you to recover your hard disk drive or reinstall selected applications and software features or utilities. ❖ During the HDD Recovery Process it is stro...

61 Getting Started Hard Drive Recovery Utilities To create recovery DVDs: 1 Click Start , All Programs , Toshiba , Recovery , and then Recovery Disc Creator . 2 Select DVD (to create Recovery media on DVDs). 3 Select the items you want to copy by clicking the check box next to the item’s Name—recove...

64 Getting Started Hard Drive Recovery Utilities 2 Select Recover to out-of-box-state , and then click Next . A confirmation message displays reminding you that all data will be lost during the recovery process. Be sure to save your work to external media before proceeding. 3 Click Next to begin the...

66 Getting Started Hard Drive Recovery Utilities 2 Select Recover without changing the hard drive partitions . A confirmation message appears, reminding you that all information on the C: drive will be lost during the recovery process. Be sure you have saved your work to external media before procee...

69 Getting Started Using the TouchPad™ Checking the HDD operating status After restoring your hard disk drive, you can check its status as follows: 1 Click Start . 2 Right-click My Computer . 3 Select Manage . 4 Click Disk Management . 5 Highlight the hard disk drive in the Volume list to display it...

70 Getting Started Using the TouchPad™ ❖ To move it to the left side, slide your finger from right to left. Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred dir...

71 Getting Started Using external display devices Using external display devices Your computer comes with a built-in display, but you can also connect the following types of external display devices to the video ports described below: ❖ An HDMI™-compatible television or VCR/DVD player via the HDMI O...

72 Getting Started Using external display devices Your computer will automatically detect the external display device and activate a screen with display options. Choose the settings you desire and click Apply . Then click OK . Connecting to a TV using HDMI™-CEC (Available on certain models) HDMI™-CE...

73 Getting Started Using external display devices ❖ Using the S/PDIF jack on the side of the computer—This lets you connect to a sound system that can accept the digital optical signal from your computer. You need an S/PDIF cable (not included with your computer) with a Toslink 1/8" (3.5mm) mini...

74 Getting Started Using external display devices Directing the display output when you turn on the computer Once you connect an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. Some modes are only available with the appropri...

75 Getting Started Using an external keyboard The right-most icon in the above illustration is for the Swap Image Display mode. This mode is available only if the current setting is an extended desktop mode (Built-in Display and External Monitor, or Built-in Display and TV). In extended desktop mode...

76 Getting Started Connecting a printer If your printer supports Plug and Play, your computer may automatically recognize the printer; the printer is then ready for use. Refer to your printer documentation for further instructions. TECHNICAL NOTE: To determine if your printer supports Plug and Play,...

77 Getting Started Connecting an optional external diskette drive Connecting an optional external diskette drive Some operations, such as creating a password service diskette, require a diskette drive designed for use with 3.5-inch diskettes. (Sample Illustration) Optional external USB diskette driv...

78 Getting Started Turning off the computer Options for turning off the computer Depending on the operating system installed, you have more than one option available for turning off the computer: Shut Down, Hibernate, and Sleep. Each option has its advantages. ❖ Use the Shut Down or Hibernate comman...

79 Getting Started Turning off the computer For information on how to use and configure Hibernation mode see “Using and configuring Hibernation mode” on page 82 . Sleep mode The Sleep command places the computer into a power-saving mode. Sleep saves the current state of the computer to memory so tha...

80 Getting Started Turning off the computer Using the Shut Down command The Shut down command completely shuts down the computer without saving your work or the current state of the computer. This command closes all open programs, shuts down the operating system, and then turns off your computer. Us...

82 Getting Started Turning off the computer Once the computer is configured, you can turn it off by either pressing the power button or closing the display panel, depending on the options set. Restarting your computer To start the computer up again, press the power button until the on/off light glow...

84 Getting Started Turning off the computer ❖ Power button action Set this option to Hibernate if you want the computer to go into Hibernation mode when you press the power button. ❖ Start menu power button Set this option to Hibernate if you want the computer to go into Hibernation mode when you cl...

85 Getting Started Turning off the computer 2 Click Sleep . The computer saves the status of all open programs and files to the memory, turns off the display, and enters into a low-power mode. The on/off light blinks amber indicating the computer is in Sleep mode. Configuring Sleep mode options You ...

87 Getting Started Customizing your computer’s settings 7 Click Apply . 8 Click OK . Once the computer is configured, you can place it into Sleep mode by either pressing the power button or closing the display panel, depending on the Sleep options set. Starting again from Sleep mode To start up the ...

88 Getting Started Caring for your computer Cleaning the computer Keep liquids, including cleaning fluid, out of the computer’s keyboard, speaker, and other openings. Never spray cleaner directly onto the computer and/or display. Never use harsh or caustic chemical products to clean the computer. To...

90 Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the internal storage drive. If the network you are usin...

92 Learning the Basics Using the keyboard Using the keyboard Your computer’s keyboard contains character keys, control keys, function keys, and special Windows ® keys. (Sample Illustration) Keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ...

93 Learning the Basics Starting a program Function keys The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard. (Sample Illustration) Function keys F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combi...

94 Learning the Basics Starting a program Starting a program from the Start menu When you install a program, the operating system usually puts an icon in the All Programs menu. To start a program that has an icon in the All Programs menu, follow these steps, which use the Windows ® WordPad program a...

95 Learning the Basics Starting a program 5 In the left part of the window, click the line that ends in “Local Disk (C:).” 6 In the left part of the window, under the Local Disk C: icon, double-click the folder containing the program, in this case Program Files . Windows ® Explorer shows the content...

96 Learning the Basics Saving your work Saving your work Before you turn off the computer using the Shut Down command, save your work on the internal storage drive, diskette, flash media, or optical disc. This is one of the most important rules of computing. When you turn off the computer using the ...

97 Learning the Basics Printing your work HINT: To make another copy of the file you are currently working with, click File , and then Save As , and give the new file a different name. File names The Windows ® operating system supports long file names that can contain up to 260 characters and can in...

98 Learning the Basics Backing up your work 2 In your Windows ® -based application, click File , and then Print . The program displays a Print dialog box. (Sample Image) Print dialog box 3 Specify the print parameters. For example, the range of pages and number of copies to print. 4 Click Print . Ba...

99 Learning the Basics Using the optical drive Restoring your work To restore information from your backup media to your internal storage drive, use the Restore page in the backup program. Look in the online Help or your operating system documentation for information on restoring files. TECHNICAL NO...

100 Learning the Basics Using the optical drive When viewing DVD movies use the DVD Player software that came with your computer. Optical drive components The optical drive is located on the side of the computer. Your optical drive may look like this: (Sample Illustration) Optical drive Drive in-use...

101 Learning the Basics Using the optical drive Media control buttons The media control buttons located on the system control panel above the keyboard let you mute the sound and play audio CDs or DVD movies when the computer is on. (Sample Illustration) Media control buttons The Media button launche...

102 Learning the Basics Using the optical drive Inserting an optical disc To insert an optical disc into the drive: 1 Make sure the computer is turned on. The drive will not open if the computer’s power is off. 2 Make sure the drive’s in-use indicator light is off. 3 Press the drive’s eject button. ...

103 Learning the Basics Using the optical drive Handle DVDs and CDs carefully, making contact only with the center hole and edge. Do not touch the surface of the disc. Do not stack discs. If you incorrectly handle the discs, you could lose data. 8 Make sure the disc is completely on the spindle and ...

104 Learning the Basics Using the optical drive Recording optical media Depending on the configuration, your computer may come with an optical drive that allows you to: ❖ Play pre-recorded and recorded optical media. ❖ Read/write data and multi-media files to recordable optical media. For more infor...

105 Learning the Basics Toshiba’s online resources Removing a disc with the computer off To remove a disc with the computer turned off: 1 Insert a slender object, such as a straightened paper clip, into the manual eject hole. The disc tray slides partially out of the drive (about 1 inch). Never use ...

106 Chapter 3 Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power suspension mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other feature...

107 Mobile Computing Running the computer on battery power Battery Notice Battery life may vary considerably from specifications depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the des...

108 Mobile Computing Charging batteries Power management Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes. Changes to these settings may result in...

109 Mobile Computing Charging batteries Charging the main battery To charge the main battery while it is in your computer, plug the computer into a live electrical outlet. The battery charges whether the computer is on or off. TECHNICAL NOTE: The recharging of the battery cannot occur when your comp...

110 Mobile Computing Monitoring main battery power If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date, or stop working. To recharge the RTC battery, plug the computer into a live electrical outlet and leave the computer powered on for 24 hours. It is ...

111 Mobile Computing Monitoring main battery power HINT: Be careful not to confuse the battery light ( ), the on/off light ( ), and the power button light. When the on/off light or power button light flashes amber, it indicates that the system is suspended (using the Windows ® operating system Sleep...

112 Mobile Computing Monitoring main battery power Highlight the power icon in the Notification Area. A pop-up message displays the remaining battery power as a percentage. With repeated discharges and recharges, the battery’s capacity gradually decreases. A frequently used older battery does not po...

113 Mobile Computing Monitoring main battery power To change the default notification settings: 1 Click Start , Control Panel , Mobile PC , and then Power Options . The Power Options window appears. 2 Click Change plan settings under the power plan to be customized. The Edit Plan Settings window app...

114 Mobile Computing Monitoring main battery power There are various ways in which you can conserve power and extend the operating time of your battery: ❖ Enable Sleep or Hibernation, which saves power when you turn off the computer and turn it back on again ❖ Use the Windows ® power-saving option p...

115 Mobile Computing Monitoring main battery power To edit a plan or to edit advanced settings, continue to the following steps. 4 Click Change Plan Settings to choose the plan you want to edit. This screen allows you to change basic settings. 5 Click Change Advanced Settings to access settings for ...

116 Mobile Computing Changing the main battery 2 While continuing to press Fn , press F2 until you select the desired Power Plan. The Power Plan options are: Balanced, Power Saver, and High Performance. 3 Release the Fn key. The hot key card disappears. You are now in the selected mode. Changing the...

118 Mobile Computing Changing the main battery Inserting a charged battery To insert a battery: 1 Wipe the terminals of the charged battery with a clean cloth to ensure a good connection. 2 Insert the charged battery into the slot until the latch clicks. The battery pack has been designed so that yo...

119 Mobile Computing Taking care of your battery 5 Reconnect any cables that were removed in step 3 of “Removing the battery from the computer” on page 116 . 6 Restart the computer. Taking care of your battery The following sections offer tips on how to take care of your battery and prolong its life...

120 Mobile Computing Taking care of your battery Maintaining your battery Fully discharging your battery pack will allow better accuracy of the battery meter. To fully discharge your battery pack: ❖ Periodically, disconnect the computer from a power source and operate it on battery power until the b...

121 Mobile Computing Disposing of used batteries Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main battery light flashes amber shortly after you have fully recharged the battery. You must discard a battery if it becomes damaged. ...

122 Mobile Computing Traveling tips Toshiba is dedicated to preserving the environment by sponsoring Call2Recycle™ , a program of the Rechargeable Battery Recycling Corporation. For more information and for drop-off locations, visit www.rbrc.org or call 1-800-822-8837. Notice regarding CR coin cell ...

123 Chapter 4 Exploring Your Computer’s Features In this chapter, you will explore some of the special features of your computer. Exploring the desktop The desktop is the launching pad for everything you can do in the Windows ® operating system. You use its features to start programs, find documents...

124 Exploring Your Computer’s Features Exploring the desktop Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, Taskbar, Notification Area, and background pattern. (Sample Image) Windows ® operating system desktop Icons An icon repres...

126 Exploring Your Computer’s Features Setting up for communications Setting up for communications To connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: ❖ A browser or communications program ❖ An Internet Service Provider (ISP) ...

127 Exploring Your Computer’s Features Setting up for communications Accessing a network To access a network: ❖ At the office, connect an Ethernet cable to the RJ45 jack on your computer. For specific information about connecting to the network, consult your network administrator. Many hotels, airpo...

129 Exploring Your Computer’s Features An overview of using the Internet An overview of using the Internet The following sections give a quick introduction to the Internet and some of its exciting features, under these headings: ❖ The Internet ❖ The World Wide Web ❖ Internet Service Providers ❖ Conn...

130 Exploring Your Computer’s Features An overview of using the Internet Connecting to the Internet To connect to the Internet, you need: ❖ A modem and telephone line, or a LAN connection ❖ A Web browser ❖ An Internet Service Provider (ISP) account Once you have established an ISP account, you can c...

131 Exploring Your Computer’s Features Exploring audio features ❖ Internet chat rooms A chat room is a Web site that offers a place where people with similar interests and ideas communicate in real-time, one-on-one or in groups, by typing messages which are instantly viewed by others on their comput...

132 Exploring Your Computer’s Features Exploring audio features 2 Click Start , All Programs , Accessories , and then Sound Recorder . (Sample Image) Sound Recorder screen 3 Click the Start Recording button. 4 Speak normally into the microphone. 5 When you have finished recording, click the Stop Rec...

133 Exploring Your Computer’s Features FM tuner FM tuner (Available on certain models) Your computer may come equipped with a built-in FM tuner and a separate FM antenna. With this FM tuner feature you can listen to live local FM radio stations. To use this feature: 1 Turn on your computer. 2 Plug i...

134 Exploring Your Computer’s Features Using an ExpressCard ® The Web Camera software, by default, should already be running in the Notification Area. Using an ExpressCard ® The ExpressCard ® slot supports the use of ExpressCard media. The slot also supports hot swapping, which allows you to replace...

135 Exploring Your Computer’s Features Using the Bridge Media Adapter Slot 3 Grasp the ExpressCard and pull it straight out. (Sample Illustration) Removing an ExpressCard Using the Bridge Media Adapter Slot The Bridge Media Adapter slot supports the use of Memory Stick ™ , Memory Stick ™ PRO, Secure...

136 Exploring Your Computer’s Features Using the i.LINK ® port When inserting memory media, do not touch the metal contacts. You could expose the storage area to static electricity, which can destroy data. Removing memory media 1 Prepare the media for removal by clicking the Safely Remove Hardware i...

137 Chapter 5 Utilities Your computer includes several utilities designed to help you to reconfigure your system to best meet your individual needs. Together, these allow you to ascertain certain system details, set additional options, or change default options. These utilities are described in this...

138 Utilities TOSHIBA Assist TOSHIBA Assist The TOSHIBA Assist provides quick access to computer functions and allows you to customize a range of computer settings. To access TOSHIBA Assist, click Start , All Programs , Toshiba , Utilities , and then TOSHIBA Assist . The TOSHIBA Assist window appear...

139 Utilities TOSHIBA Assist Connect The features available in this category are: ❖ ConfigFree ® Connectivity Doctor ❖ Bluetooth ® Settings ❖ Bluetooth ® Local COM Settings (Sample Image) TOSHIBA Assist window – Connect tab

140 Utilities TOSHIBA Assist Secure The features available in this category are: ❖ Supervisor password ❖ User password (Sample Image) TOSHIBA Assist window – Secure tab

142 Utilities TOSHIBA Assist Optimize The features available in this category are: ❖ Mouse Utility ❖ TOSHIBA Hardware Setup ❖ TOSHIBA Zooming Utility ❖ TOSHIBA Button Support ❖ CD/DVD Drive Acoustic Silencer ❖ TOSHIBA Accessibility (Sample Image) TOSHIBA Assist window – Optimize tab

143 Utilities Setting passwords Setting passwords Setting a password lets you walk away from your computer while providing additional protection for your files. When you set a password, you must enter the password before you can work on your computer again. Toshiba supports several types of password...

144 Utilities Setting passwords Using a supervisor password A supervisor password prevents other users from changing hardware configuration options. Setting a supervisor password If you choose to set a supervisor or user password, Toshiba strongly recommends that you save your password in a location...

145 Utilities Setting passwords 6 Click OK . A pop-up screen appears asking for the User Password Mode. 7 Select whether the user password allows the user to change the hardware configuration: ❖ Able to run HwSetup —User can change the hardware configuration ❖ Unable to run HwSetup —User cannot chan...

146 Utilities Setting passwords To register a password for the power-on password functions: 1 Click Start , All Programs , Toshiba , Utilities , and then TOSHIBA Assist . The TOSHIBA Assist window appears. 2 On the left side, click the Secure tab. 3 Double-click the User Password icon. The Password ...

147 Utilities TOSHIBA PC Diagnostic Tool Utility 4 Click Not Registered. A pop-up screen appears asking for a password. 5 Enter the user password, then click OK . TOSHIBA PC Diagnostic Tool Utility This utility can help diagnose problems with devices in your computer. Refer to the online Help docume...

148 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. To access the Mouse utility: 1 Click Start , Control Panel , and then Mouse under Hardware and Sound , or click the Mouse icon in the Optimize tab of TOSHIBA Assist . The Mouse Pr...

149 Utilities TOSHIBA Hardware Setup TOSHIBA Hardware Setup TOSHIBA Hardware Setup is the Toshiba configuration management tool available through the Windows ® operating system. To access it: ❖ Click Start , All Programs , Toshiba , Utilities , and then HWSetup , or click the TOSHIBA Hardware Setup ...

153 Utilities TOSHIBA Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot keys (see “Zoom (Display resolution)” on page 209 ). You may select all applications or any subset of the following: ❖ Microsoft ® Internet Explorer ®...

154 Utilities TOSHIBA Button Support The zoom in and zoom out hot keys will now work with the applications you selected. To zoom in, hold down the Fn key and press 2 ; to zoom out, hold down the Fn key and press 1 . For more information about how to use the TOSHIBA Zooming Utility, right-click the i...

155 Utilities CD/DVD Drive Acoustic Silencer CD/DVD Drive Acoustic Silencer This utility can slow the speed of your optical drive to make it run more quietly. You can use this utility to make listening to music CDs more enjoyable. When you change the optical drive to “Silence” mode, the setting is o...

156 Utilities TOSHIBA Accessibility TOSHIBA Accessibility The TOSHIBA Accessibility utility allows you to use the Fn key to create a hot key combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the Fn key a s...

157 Utilities Fingerprint Authentication Utility Fingerprint Authentication Utility (Available on certain models) The fingerprint authentication utility (available on certain models) can be used to replace the keyboard-based user password authentication system when booting up. The fingerprint authen...

158 Utilities Fingerprint Authentication Utility Fingerprint Logon The fingerprint utility enables logon to your computer using fingerprints. During user enrollment, fingerprint samples are saved and associated with the user’s Windows ® user account. When the user attempts to log on again, the user’...

159 Utilities Fingerprint Authentication Utility ❖ Avoid the following finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate. ❖ Soaked or swollen finger (e.g., after taking bath) ❖ Injured finger ❖ We...

160 Utilities ConfigFree® ❖ The recognition success rate may differ from user to user. ❖ Toshiba does not guarantee that this fingerprint recognition technology will be error-free. Toshiba does not guarantee that the fingerprint reader will recognize the enrolled user or accurately screen out unauth...

161 Utilities ConfigFree® Starting ConfigFree ® To start ConfigFree ® , be sure the computer has a wired or wireless connection. Then perform any of the following steps: ❖ Click Start , All Programs , Toshiba , Networking , and then ConfigFree . ❖ Double-click the ConfigFree icon in the Notification...

162 Utilities ConfigFree® ❖ Status of Wireless Connection switch (Sample Image) Connectivity Doctor screen Profile Settings The Profile Settings utility lets you save network settings in “profiles.” ConfigFree ® profiles are useful for easily switching network settings and devices. You can switch ne...

164 Chapter 6 If Something Goes Wrong Some problems you may encounter when using your computer are relatively easy to identify and solve. Others may require help from your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems by yourself...

165 If Something Goes Wrong Problems when you turn on the computer 2 Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End Task . Closing the failed program should allow y...

166 If Something Goes Wrong Problems when you turn on the computer If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the AC power light. If the indicator is glowing, the computer is connected to a live external power source. The ...

167 If Something Goes Wrong Problems when you turn on the computer If you are running on battery power, it is recommended that you do not leave the computer in Sleep mode for long periods of time. To charge the battery, leave the computer plugged into a live wall outlet for several hours. For more i...

168 If Something Goes Wrong The Windows ® operating system is not working 5 Verify that the AC adaptor is the correct unit for your computer model. The computer may not be able to start from an AC adaptor that is rated for less current (amperage) than the computer requires, even if the rated voltage...

169 If Something Goes Wrong The Windows ® operating system is not working ❖ Safe Mode with Command Prompt ❖ Enable Boot Logging ❖ Enable low-resolution video (640x480) ❖ Last Known Good Configuration (advanced) ❖ Directory Services Restore Mode ❖ Debugging Mode ❖ Disable automatic restart on system ...

170 If Something Goes Wrong Resolving a hardware conflict The Windows ® operating system can help you If the operating system has started properly but you still have a problem using your computer, the online Help can assist you in troubleshooting the problem. To access the Windows ® operating system...

171 If Something Goes Wrong Resolving a hardware conflict The device most recently connected to the system is the one most likely to be causing a conflict. Resolving conflicts There are several things you can do to resolve hardware conflicts: ❖ Get the most recent drivers from the manufacturer. ❖ Di...

172 If Something Goes Wrong Resolving a hardware conflict ❖ The Resources tab, which lists resources assigned to the monitor, optional external optical drive, optional external diskette drive, and other power-using functions. This tab does not appear if the device is not using resources. ❖ The Drive...

173 If Something Goes Wrong Resolving a hardware conflict For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. Power and the batteries Your computer receives its power through the AC adaptor and power cord/cab...

174 If Something Goes Wrong Resolving a hardware conflict The battery appears not to power the computer for as long as it usually does. If you frequently repeat shallow charge and discharge, the battery meter may become inaccurate. Let the battery discharge completely, then try charging it again. Ch...

175 If Something Goes Wrong Resolving a hardware conflict Display problems Here are some typical display problems and their solutions: The screen is blank. Display Auto Off may have gone into effect. Press any key to activate the screen. You may have activated the instant password feature by pressin...

177 If Something Goes Wrong Resolving a hardware conflict Disk or internal storage drive problems Problems with the internal storage drive or with a diskette drive usually show up as an inability to access the drive or as sector errors. Sometimes a drive problem may cause one or more files to appear...

178 If Something Goes Wrong Resolving a hardware conflict Your data files are damaged or corrupted. Refer to your software documentation for file recovery procedures. Many software packages automatically create backup files. You may also be able to recover lost data using utility software. Consult y...

179 If Something Goes Wrong Resolving a hardware conflict You press the disc eject button, but the drive tray does not slide out. Make sure the computer is connected to a power source and turned on. The optical drive eject mechanism requires power to operate. Make sure a program is not accessing the...

180 If Something Goes Wrong Resolving a hardware conflict The computer emits a loud, high-pitched noise. This is feedback between the microphone and the speakers. It occurs in any sound system when input from a microphone is fed to the speakers and the speaker volume is too loud. Adjust the volume c...

181 If Something Goes Wrong Resolving a hardware conflict 2 Double-click the appropriate ExpressCard, which will be listed under one of the categories shown, for example: Disk drives, Network adapters, Other, etc. The operating system displays your ExpressCard’s Properties dialog box, which contains...

182 If Something Goes Wrong Resolving a hardware conflict An ExpressCard ® error occurs. Reinsert the card to make sure it is properly connected. If the card is attached to an external device, check that the connection is secure. Refer to the card’s documentation, which should contain a troubleshoot...

183 If Something Goes Wrong Resolving a hardware conflict Modem problems (Available on certain models) This section lists common modem problems. The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port ...

186 If Something Goes Wrong DVD operating problems DVD operating problems If you experience a problem playing DVDs, you may be able to fix the problem yourself. For general problems playing a DVD title, try the following steps: 1 Verify that the disc is in a format that the drive supports. 2 Ensure ...

187 If Something Goes Wrong Develop good computing habits Develop good computing habits Save your work frequently. You can never predict when your computer will lock, forcing you to close a program and lose unsaved changes. Many software programs build in an automatic backup, but you should not rely...

188 If Something Goes Wrong Develop good computing habits Data and system configuration backup in the Windows ® operating system The Windows ® operating system offers some easy-to-use features for backing up your Windows ® settings and your data—documents and other important files. Take advantage of...

189 If Something Goes Wrong Develop good computing habits Then, at a later time, you can re-establish your Windows ® configuration using the saved Restore Point. To do this: 1 Click Start , All Programs , Accessories , System Tools , and then System Restore . 2 Click Next . 3 A list of previously cr...

190 If Something Goes Wrong Develop good computing habits Follow these steps to back up your computer or files to optical discs, or a storage drive: You cannot back up the computer while running on battery power. Connect the AC adaptor before continuing. 1 Prepare your backup target by connecting it...

191 If Something Goes Wrong Develop good computing habits ❖ Have your factory Restore/Reconfiguration CD(s) on hand in case you need any files from them (available on certain models). ❖ Do not guess—follow directions carefully! It is often necessary to run an installation utility first—before connec...

192 If Something Goes Wrong If you need further assistance ❖ Turn OFF the computer while external devices are connected. ❖ Connect external devices after turning OFF the computer. If this function cannot be used, change the setting to Disabled. ❖ Make sure that you are connected to a compatible port...

193 If Something Goes Wrong If you need further assistance ❖ If the problem occurs while you are running a program, consult the program’s documentation for troubleshooting suggestions. Contact the software company’s technical support group for their assistance. ❖ Consult the dealer from whom you pur...

194 If Something Goes Wrong Other Toshiba Internet Web sites Other Toshiba Internet Web sites Toshiba’s worldwide offices toshiba.com Worldwide Toshiba corporate site computers.toshiba.com Marketing and product information in the USA accessories.toshiba.com Accessories information in the USA www.tos...

195 If Something Goes Wrong Toshiba’s worldwide offices For more information on additional Toshiba worldwide locations, please visit: www.toshiba.co.jp/index.htm . Spain Toshiba Information Systems (España) S.A.Parque Empresarial San FernandoEdificio Europa, 1a Planta Escalera A28831 (Madrid) San Fe...

196 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot keys and TOSHIBA Cards provide a quick way to modify selected system functions and to launch applications. There are two types of TOSHIBA Cards: Hot Key Cards and Application Cards. Hot Key Cards The Hot Key Cards are used to set or mod...

197 Hot Keys/TOSHIBA Cards Hot Key Cards 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Key Cards are normally hidden from view. The Cards appear when you press the Fn key. Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a l...

198 Hot Keys/TOSHIBA Cards Application Cards 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: Not all functions are supported on all models. TOSHIBA Assist For more information, refer to “TOSHIBA Assist” on page 138 . PC Diagnostic Tool utility For...

199 Hot Keys/TOSHIBA Cards Application Cards 5.375 x 8.375 ver 2.3 Using the Application Cards To launch an application using the Application Cards: 1 Press and hold the Fn key. The TOSHIBA Cards display at the top of the screen. (Sample Image) TOSHIBA Card display 2 Click the “stacked” card on the ...

200 Hot Keys/TOSHIBA Cards Hot key functions 5.375 x 8.375 ver 2.3 3 The Card Case displays two rows of Cards. Cards that appear solid (not transparent) in the bottom row are enabled and can be selected when the Application Cards are displayed. The top row contains all of the disabled cards. 4 To en...

202 Hot Keys/TOSHIBA Cards Hot key functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIBA Card or hot key displays the power plans and cycles through the power plans. The properties of each power plan, and the power plans that are displayed by this function, are set in the Power Options win...

204 Hot Keys/TOSHIBA Cards Hot key functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIBA Card or hot key places the computer into Hibernation mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hib...

206 Hot Keys/TOSHIBA Cards Hot key functions 5.375 x 8.375 ver 2.3 Display brightness Cycle through the display modes, then select the desired mode. Not all functions are supported on all models. Some systems also support an additional Swap Image Display mode. This mode is available only if the curr...

207 Hot Keys/TOSHIBA Cards Hot key functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIBA Card or hot key enables/disables the optional wireless devices installed in your computer. The wireless modes are: ❖ Wi-Fi ® enabled—Enables just the Wi-Fi ® module. ❖ Bluet...

208 Hot Keys/TOSHIBA Cards Hot key functions 5.375 x 8.375 ver 2.3 Disabling or enabling the TouchPad™ or Fn + This TOSHIBA Card or hot key enables/disables the TouchPad. For more information on using the TouchPad, see “Disabling or enabling the TouchPad™” on page 70 . Selecting this Card or pressin...

210 Hot Keys/TOSHIBA Cards Hot key functions 5.375 x 8.375 ver 2.3 Keyboard hot key functions Fn + This hot key turns the TOSHIBA Zooming Utility to zoom-out. Fn + This hot key turns the TOSHIBA Zooming Utility to zoom-in.

211 5.375 x 8.375 ver 2.3 Appendix B Power Cord/Cable Connectors Your computer ships with the correct power supply for the country of purchase. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. USA and Canada UL approvedCSA approved United K...

212 Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. AC alternating current BIOS basic input/output system bps bits per second CD compact disc CD-ROM compact disc read-only memory C...

214 Glossary SDRAM synchronous dynamic random access memory SRAM static random access memory SSD Solid State Drive SVGA super video graphics adapter TFT thin film transistor USB universal serial bus URL uniform resource locator WAN wide area network www World Wide Web Terms The following terms may a...

226 Index A AC adaptor 46 AC power connecting adaptor 47 accessories memory 51 adding memory 51 Alt keys 92 Application Cards 198 audio files 131 audio features 131 B backing up files 91 battery changing 116 charge indicator light 47 , 110 charge not lasting 174 charging 46 , 48 conserving power 113...