Page 2 - ii; Copyright; Toshiba PORTEGE R200 Maintenance Manual; Disclaimer
ii [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Copyright © 2005 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of ...
Page 3 - iii; Preface; SAFETY PRECAUTIONS; serious bodily injury, if the safety instruction is not observed.
PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] iii Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer PORTEGE R200, referred to as PORTEGE R200 in this manual. The procedures described in this manual are intended to help ...
Page 4 - iv
iv [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) The manual is divided into the following parts: Chapter 1 Hardware Overview describes the PORTEGE R200 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diag...
Page 5 - Conventions; Acronyms; boldface; Key operation; Ctrl; and at the same time press
PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] v Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following ...
Page 6 - vi; Table of Contents; Chapter 1
vi [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Table of Contents Chapter 1 Hardware Overview 1.1 Features ...................................................................................................................... 1-1 1.2 1.8-inch Hard Disk Drive.................................
Page 7 - vii; Chapter 3; ONE
PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] vii Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test ................................................
Page 8 - viii; Chapter 4; board
viii [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Chapter 4 Replacement Procedures 4.1 Overview .............................................................................................................. 4-1 4.2 Battery pack ...............................................................
Page 9 - ix; Appendices
PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] ix Appendices Appendix A Handling the LCD Module ........................................................................ A-1 Appendix B Board Layout ................................................................................................
Page 12 - Hardware Overview
1 Hardware Overview 1-ii [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 1 Hardware Overview
Page 13 - Inverter
1 Hardware Overview PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 1-iii Chapter 1 Contents 1.1 Features ...................................................................................................................... 1-1 1.2 1.8-inch Hard Disk Drive.....................................
Page 14 - Figures
1 Hardware Overview 1-iv [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Figures Figure 1-1 Front of the computer..................................................................................... 1-4 Figure 1-2 System unit configuration ......................................................
Page 24 - Standard value
1 Hardware Overview 1.2 1.8-inch Hard Disk Drive 1.2 1.8-inch Hard Disk Drive A compact, high-capacity HDD with a height of 5.0/8.0mm. Contains a 1.8-inch magnetic disk and magnetic heads. Figure 1-4 shows a view of the 1.8-inch HDD and Tables 1-1 and 1-2 list the specifications. Figure 1-4 1.8-inch...
Page 25 - Specification
1.2 1.8-inch Hard Disk Drive 1 Hardware Overview PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 1-11 Table 1-2 1.8-inch HDD Specifications Specification Parameter TOSHIBA HDD1442BZL01 TOSHIBA HDD1544BZK01 Storage size (formatted) 30GB 60GB Speed (RPM) 4,200 Data transfer speed (Mbits/s) 13...
Page 27 - TFT Color Display; Module; 68 resolution. The video controller; Specifications
1.4 TFT Color Display 1 Hardware Overview PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 1-13 1.4 TFT Color Display The TFT color display consists of a LCD module and FL inverter board. 1.4.1 LCD Module The LCD module used for the TFT color display uses a backlight as the light source and ...
Page 29 - Supply
1.5 Power Supply 1 Hardware Overview PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 1-15 1.5 Power Supply The power supply supplies twenty-three different voltages to the system board. The power supply microcontroller has the following functions. 1. Judges that the DC power supply (AC adap...
Page 30 - Name
1 Hardware Overview 1.5 Power Supply 1-16 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Table 1-5 lists the power supply output specifications. Table 1-5 Power supply output specifications Name Voltage (V) Use PPV 0.940 - 0.81 CPU (ULV) PTV 1.05 CPU, GMCH, ICH6-M 1R5-P1V 1.5 CPU, GMCH, IC...
Page 31 - Battery name; Battery
1.6 Batteries 1 Hardware Overview PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 1-17 1.6 Batteries The PC has the following three batteries. Main battery Secondary battery (option) Real time clock (RTC) battery Table 1-6 lists the specifications for these two batteries. Table 1-6 Battery ...
Page 32 - Charging Time; Table 1-8 RTC battery charging/data preservation time; Time
1 Hardware Overview 1.6 Batteries 1-18 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 1.6.2 Battery Charging Control Battery charging is controlled by a power supply microprocessor. The power supply microprocessor controls power supply and detects a full charge when the AC adaptor and batt...
Page 33 - Adapter; The AC adapter is also used to charge the battery.
1.7 AC Adapter 1 Hardware Overview PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 1-19 1.7 AC Adapter The AC adapter is also used to charge the battery. Table 1-9 lists the AC adapter specifications. Table 1-9 AC adapter specifications Parameter Specification G71C0001A310 G71C0001A410 G71C...
Page 36 - Troubleshooting
2 Troubleshooting 2-ii [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 2
Page 37 - Chapter 2
2 Troubleshooting PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-iii Chapter 2 Contents 2.1 Troubleshooting ......................................................................................................... 2-1 2.2 Troubleshooting Flowchart ...........................................
Page 42 - Flowchart; Ask user to enter the password if a password is registered.
2 Troubleshooting 2.2 Troubleshooting Flowchart 2-2 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide for determining which FRU malfunctions. Before going through the flowchart steps, check the following: Ask user to e...
Page 46 - Procedure 1: Power supply icon Check
2 Troubleshooting 2.3 Power Supply Troubleshooting 2-6 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 2.3 Power Supply Troubleshooting The power supply controller controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and co...
Page 47 - Procedure 1; The following two icons indicate the power supply status:; Battery icon; icon; DC IN icon
2.3 Power Supply Troubleshooting 2 Troubleshooting Procedure 1 Power supply icon Check The following two icons indicate the power supply status: Battery icon DC IN icon The power supply controller uses the power supply status with the Battery icon and the DC IN icon as listed in the tables below...
Page 49 - Procedure 2
2.3 Power Supply Troubleshooting 2 Troubleshooting Procedure 2 Error Code Check If the power supply microprocessor detects a malfunction, the DC IN icon blinks orange. The blink pattern indicates an error as shown below. Start Off for 2 seconds Error code (8 bit) “1” On for one second “0” On for...
Page 50 - Error code
2 Troubleshooting 2.3 Power Supply Troubleshooting 2-10 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Check 1 Convert the DC IN icon blink pattern into the hexadecimal error code and compare it to the tables below. Then go to Check 2. Table 2-3 Error code Error code Where Error occurs 1*h...
Page 54 - Procedure 3
2 Troubleshooting 2.3 Power Supply Troubleshooting Procedure 3 Connection Check The wiring diagram related to the power supply is shown below: Any of the connectors may be disconnected. Perform starting from Check 1. Check 1 Make sure the AC adapter and the AC power cord are firmly plugged into the ...
Page 55 - Procedure 4
2.3 Power Supply Troubleshooting 2 Troubleshooting PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-15 Procedure 4 Charge Check Check if the power supply controller charges the battery pack properly. Perform the following procedures: Check 1 Make sure the AC adapter is firmly plugged into ...
Page 56 - System board Troubleshooting; Procedure 1: Message Check
2 Troubleshooting 2.4 System board Troubleshooting 2-16 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 2.4 System board Troubleshooting This section describes how to determine if the System board is defective. Start with Procedure 1 and continue with the other procedures as instructed. The...
Page 57 - PRESS ANY KEY TO CONTINUE.
2.4 System board Troubleshooting 2 Troubleshooting PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-17 Procedure 1 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. The IRT tests each IC on the System board and init...
Page 59 - Figure 2-2 A set of tool for debug port test; Test board
2.4 System board Troubleshooting 2 Troubleshooting Procedure 2 Debug Port Check Check the D port status by a debug port test. The tool for debug port test is shown below. Figure 2-2 A set of tool for debug port test The test procedures are follows: 1. Connect the debug test cable to the connector CN...
Page 68 - Check 1
2 Troubleshooting 2.4 System board Troubleshooting 2-28 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Table 2-4 D port status (8/8) LED Status Test item Message HW initialization prior to boot, Waiting for the completion of HW initialization Notifies the DVI connection status to VGA BIOS ...
Page 69 - Tests and Diagnostic,; Replacement Procedures
2.4 System board Troubleshooting 2 Troubleshooting PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-29 Procedure 3 Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. These tests check the System board and I/O unit. Refer to Chapter 3, Tests a...
Page 70 - USB FDD Troubleshooting; Procedure 1: FDD Head Cleaning Check; Detailed operation is given in Chapter 3,
2 Troubleshooting 2.5 USB FDD Troubleshooting 2-30 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 2 2.5 USB FDD Troubleshooting This section describes how to determine if the USB FDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other pr...
Page 71 - Tests and Diagnostics,; Code Status; Write protected; Check 2
2.5 USB FDD Troubleshooting 2 Troubleshooting PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-31 Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD of the computer, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics...
Page 73 - Troubleshooting
2.6 1.8” HDD Troubleshooting 2 Troubleshooting PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-33 2.6 1.8” HDD Troubleshooting This section describes how to determine if the 1.8” HDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other p...
Page 74 - HDC ERROR
2 Troubleshooting 2.6 1.8” HDD Troubleshooting 2-34 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Procedure 2 Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. When the test detects an error, an error message is di...
Page 75 - FORMAT
2.6 1.8” HDD Troubleshooting 2 Troubleshooting PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-35 Procedure 3 Format Check The computer’s 1.8” HDD is formatted using the MS-DOS FORMAT program or the physical format program of the test program. To format the 1.8" HDD, start with Check ...
Page 77 - Procedure 5; HDD
2.6 1.8” HDD Troubleshooting 2 Troubleshooting Procedure 5 Connector Check and Replacement Check HDD is connected to the system board via HD FPC. The connection of HDD, HD FPC or system board may be defective. Otherwise, they may be faulty. Disassemble the computer following instructions in Chapter ...
Page 78 - Troubleshooting; System board
2 Troubleshooting 2.7 Keyboard Troubleshooting 2.7 Keyboard Troubleshooting To determine if the computer’s keyboard is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic Test Program Execution C...
Page 79 - Procedure 1: External Monitor Check; Tests
2.8 Display Troubleshooting 2 Troubleshooting PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-39 2.8 Display Troubleshooting This section describes how to determine if the computer’s display is functioning properly. Start with Procedure 1 and continue with the other procedures as instruct...
Page 82 - Pad; Procedure 1: Diagnostic Test Program Execution Check; Touch Pad
2 Troubleshooting 2.9 Touch Pad 2.9 Touch Pad To determine whether the Touch Pad is faulty or not, perform the following procedures: Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Cable Check Procedure 3: Replacement Check Procedure 1 Diagnostic Test Program Ex...
Page 83 - Tests and Diagnostics
2.10 Modem 2 Troubleshooting PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-43 2.10 Modem To check if the modem is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and...
Page 87 - Tests and
2.12 Sound 2 Troubleshooting 2.12 Sound To check if the sound function is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check Procedure 3: Replacement Check Procedure 1 Diagnostic Te...
Page 89 - Bluetooth Troubleshooting; Procedure 1: Transmitting-Receiving Check
2.13 Bluetooth Troubleshooting 2 Troubleshooting PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-49 2.13 Bluetooth Troubleshooting To check if the Bluetooth is malfunctioning or not, follow the troubleshooting procedures below as instructed. Procedure 1: Transmitting-Receiving Check Proce...
Page 90 - The Bluetooth function-wiring diagram is shown below:
2 Troubleshooting 2.13 Bluetooth Troubleshooting Procedure 2 Antennas' Connection Check The Bluetooth function-wiring diagram is shown below: Any of the connections may be defective. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures , and perform the followi...
Page 91 - for instructions on how to disassemble the computer and then
2.13 Bluetooth Troubleshooting 2 Troubleshooting PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 2-51 Procedure 3 Replacement Check Bluetooth module, Bluetooth antenna or system board may be faulty. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the compu...
Page 92 - Wireless LAN Troubleshooting
2 Troubleshooting 2.14 Wireless LAN Troubleshooting 2-52 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 2.14 Wireless LAN Troubleshooting To check if the wireless LAN is good or no good, follow the troubleshooting procedures below as instructed. Procedure 1: Transmitting-Receiving Check Pr...
Page 95 - SD card
2.15 SD card slot 2 Troubleshooting 2.15 SD card slot To check if the SD card slot is good or no good, follow the troubleshooting procedures below as instructed. Procedure 1: Check on Windows Procedure 2: Connector Check and Replacement Check Procedure 1 Check on Windows Insert a SD card into the sl...
Page 96 - Fingerprint sensor; When failed in Procedure 1 to Procedure 3, execute Procedure 4.
2 Troubleshooting 2.16 Fingerprint sensor 2.16 Fingerprint sensor CAUTION: To delete the account for confirming the fingerprint operation, it is necessary to log on by the account with the management authority. If the password has been set to log on, ask the Log-ON password to the user. To check if ...
Page 101 - Turn on the computer and start up the Windows.
2.16 Fingerprint sensor 2 Troubleshooting 11. Close all applications and power off the computer. Procedure 3 Authentication of fingerprint 1. Turn on the computer and start up the Windows. 2. In the Windows Log-ON window, scan the fingerprint of your right index finger. Make sure that scanned finger...
Page 104 - Tests and Diagnostics
3 Tests and Diagnostics 3-ii [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3
Page 105 - Tests and Diagnostics
3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-iii Chapter 3 Contents 3.1 The Diagnostic Test ................................................................................................... 3-1 3.1.1 Diagnostics menu ..............................................
Page 108 - Figure
3 Tests and Diagnostics 3-vi [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Figure Figure 3-1 Name and positions of each side........................................................................ 3-49 Tables Table 3-1 Subtest names ...........................................................
Page 109 - The Diagnostic Test; Check all cables are connected firmly.; menu
3.1 The Diagnostic Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-1 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test programs to test the functions of the computer’s hardware modules. The Diagnostics Programs are stored on some D...
Page 112 - Executing the Diagnostic Test; Enter
3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-4 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.2 Executing the Diagnostic Test To start the DIAGNOSTIC PROGRAM, follow these steps: 1. Insert the Diagnostics disk in the floppy disk drive. 2. Release the lock of the power swit...
Page 113 - The following menu appears.
3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3.2.1 Diagnostics menu (T&D) To execute this program, select 1- Repair Main (T&D) in the startup menu, press Enter . The following menu appears. TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20X...
Page 114 - . The following DIAGNOSTIC TEST MENU; DIAGNOSTIC TEST MENU :; the highlight bar to function 99 and press
3 Tests and Diagnostics 3.2 Executing the Diagnostic Test Set the highlight bar to 1 , and press Enter . The following DIAGNOSTIC TEST MENU will appear: TOSHIBA personal computer XXXXXX DIAGNOSTICS version X.XX (c) copyright TOSHIBA Corp. 20XX DIAGNOSTIC TEST MENU : 1 - SYSTEM TEST 2 - MEMORY TEST 3...
Page 115 - TEST; SYSTEM TEST NAME XXXXXX; ERROR STOP
3.2 Executing the Diagnostic Test 3 Tests and Diagnostics Select the option you want to execute and press Enter . When you select 1-SYSTEM TEST , the following message will appear: SYSTEM TEST NAME XXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key stop SUB-TEST : XX PAS...
Page 116 - YES; Terminates the test program and exits to the subtest menu.
3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 3-8 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Selecting YES of ERROR STOP stops the test program when an error is found and displays the operation guide on the right side of the display screen as shown below: ERROR STATUS NAME ...
Page 117 - Setting of the hardware configuration; -Repair initial config set; Enter Version Number ?; Enter Serial Number ?
3.3 Setting of the hardware configuration 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-9 3.3 Setting of the hardware configuration To execute this program, select 2-Repair initial config set in the startup menu, press Enter and follow the directions on the scree...
Page 118 - DMI information to the floppy disk.
3 Tests and Diagnostics 3.3 Setting of the hardware configuration 3-10 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) • Setting of the HWSC • Setting of the UUID • Display of the DMI information (including UUID) • Setting of DVD region code (Yes/No) After completion of the above settings, ...
Page 119 - Press
3.3 Setting of the hardware configuration 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-11 Subtest 08 System configuration display This subtest displays the information of the system configuration. When the following message appears, confirm the contents and pres...
Page 120 - Test; To execute this program, select; of the SYSTEM test will be executed.; Press any key and return to the startup menu.
3 Tests and Diagnostics 3.4 Heatrun Test 3-12 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.4 Heatrun Test To execute this program, select 3-Repair heatrun (T&D) in the startup menu, press Enter . When selecting the option you want to execute, the message shown below will appear and...
Page 121 - Names; Test Name
3.5 Subtest Names 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-13 3.5 Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/2) No. Test Name Subtest No. Subtest Name 1 SYSTEM 01 02 03 04 05 ...
Page 126 - To execute the Keyboard Test, select; Scan
3 Tests and Diagnostics 3.8 Keyboard Test 3-18 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.8 Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execu...
Page 128 - To exit this subtest and return to the DISPLAY TEST menu, press; after
3 Tests and Diagnostics 3.9 Display Test Subtest 04 Gradation & Mode test for VGA This subtest displays gradations for following modes. To change the mode, press Enter . [Mode 12] [Mode 13] [Mode 3 ] [Mode 111 640*480 64K] [Mode 112 640*480 16M] [Mode 114 800*600 64K] [Mode 115 800*600 16M] [Mod...
Page 130 - Floppy Disk Test; To execute the Floppy Disk Test, select; and follow the directions displayed on the screen.; The Floppy Disk test contains five subtests that test the FDD.
3 Tests and Diagnostics 3.10 Floppy Disk Test 3.10 Floppy Disk Test CAUTION: Before running the floppy disk test, prepare a formatted work disk. Remove the Diagnostics Disk and insert the work disk into the FDD because the contents of the floppy disk will be erased. To execute the Floppy Disk Test, ...
Page 132 - Also, printer port wraparound connector must be connected.
3 Tests and Diagnostics 3.11 Printer Test 3.11 Printer Test CAUTION: Printer Test is not supported for this model. To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. NOTE: An IBM compatible printer must be connected to the system...
Page 134 - and; Subtest 01 and 02 require the following data format:
3 Tests and Diagnostics 3.12 Async Test 3-26 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.12 Async Test CAUTION: Async Test is not supported for this model. To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen....
Page 135 - Hard Disk Test; Refer to the operating system instructions.; Test drive number select; Detail status display
3.13 Hard Disk Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-27 3.13 Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. CAUTION: The contents of the hard disk will be era...
Page 137 - Worst pattern data; Partial Read
3.13 Hard Disk Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-29 Subtest 04 Cross talk & peak shift This subtest writes eight types of worst pattern data (listed below) to a cylinder and then reads the data while moving from cylinder to cylinder. (Tests t...
Page 138 - Real Timer Test
3 Tests and Diagnostics 3.14 Real Timer Test 3-30 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3 3.14 Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you wan...
Page 141 - Sub# Address Good Bad
3.16 Expansion Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-33 3.16 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. Subtest 01 PCMCIA wraparound NOTE: To execute th...
Page 143 - and follow the directions on the screen.
3.17 CD-ROM/DVD-ROM Test 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-35 3.17 CD-ROM/DVD-ROM Test To execute the CD-ROM/DVD-ROM test, select 12 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. NOTE: For the subtest 01, 02 and ...
Page 144 - Error Code and Error Status Names; Device name
3 Tests and Diagnostics 3.18 Error Code and Error Status Names 3-36 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.18 Error Code and Error Status Names Table 3-2 lists the error codes and error status names for the Diagnostic Test. Table 3-2 Error codes and error status names (1/3) Devic...
Page 147 - Hard Disk Test Detail Status; HDC status = XXXXXXXX; Bit Name
3.19 Hard Disk Test Detail Status 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-39 3.19 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk tes...
Page 149 - Description
3.20 ONLY ONE TEST 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-41 3.20 ONLY ONE TEST 3.20.1 Program Description This program tests the unique functions of this model. 3.20.2 Operations Select test 2 from the DIAGNOSTIC MENU and press Enter . The following menu ...
Page 152 - Press [Toshiba Presentation button] button; Kill Switch; Kill switch is set to a start position (OFF)
3 Tests and Diagnostics 3.20 ONLY ONE TEST Subtest 03 GP Button This subtest checks moving of the front operation panel button. Press the Toshiba Presentation button after the following message appears. Press [Toshiba Presentation button] button Power switch Toshiba Presentation Toshiba Assist Press...
Page 156 - Device Lock TEST OK...; When it passes the test, following message appears.; Device Lock TEST NG...; and return to the ONLY ONE TEST menu.
3 Tests and Diagnostics 3.20 ONLY ONE TEST 3-48 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Subtest 08 PC-Card Device Lock This subtest checks the device lock function. This test needs a PC card, not a PC wraparound card. Before this test, inset a PC card. When it passes the test, follo...
Page 157 - Vertical plane; The figure below shows the name and position of each side.; Back
3.20 ONLY ONE TEST 3 Tests and Diagnostics Subtest 0A Acceleration sensor This subtest detects and corrects the each axis (X, Y, Z). NOTE: Make sure that this subtest is executed on the following condition: 1. Flat desk with vertical plane to get the stability of machine. 2. Prevent the machine from...
Page 159 - Cleaning; Selecting test; displays the; Press any key when ready.; When the; cleaning start; message appears, the FDD head cleaning has begun.
3.21 Head Cleaning 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-51 3.21 Head Cleaning 3.21.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this p...
Page 160 - Utilities; The error information is displayed in the following order:
3 Tests and Diagnostics 3.22 Log Utilities 3-52 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.22 Log Utilities 3.22.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy d...
Page 161 - STS ADDR
3.22 Log Utilities 3 Tests and Diagnostics 3.22.2 Operations 1. Select 5 and press Enter in the DIAGNOSTIC MENU, the error information is displayed in the following format: XXXXX ERRORS CNT TS-NO PASS STS ADDR WD RD HSTS [ERROR STATUS NAME] 001 FDD 02 0000 103 00001 00 00 0000 FDD-WRITE PROTECTED 00...
Page 163 - Floppy Disk Drive Utilities
3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-55 3.24 Floppy Disk Drive Utilities 3.24.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOT...
Page 164 - Format start
3 Tests and Diagnostics 3.24 Floppy Disk Drive Utilities 3-56 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.24.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message. [ FDD UTILITIES ] 1 - FORMAT 2 - COPY 3 - DUMP 4 – HDD-ID READ 9 - EXIT ...
Page 165 - Copy start
3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-57 3. COPY program (a) When COPY is selected, the following message appears. FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number w...
Page 167 - Model
3.24 Floppy Disk Drive Utilities 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-59 (k) The following message will appear. To finish the dump, select 3 . Press number key (1:up,2:down,3:end) ? (l) The following message will appear. Selecting 2 returns to the FDD UT...
Page 168 - System Configuration
3 Tests and Diagnostics 3.25 System Configuration 3-60 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3 3.25 System Configuration 3.25.1 Function Description NOTE: To display the system configuration, the write protect tab should be OFF position. If the tab is ON position, move the tab to ...
Page 171 - Setting Responder PC
3.26 Wireless LAN Test Program (Atheros) 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-63 3.26.1 Setting Responder PC 1. When the responder PC has MB44a/g or MB43 Insert the FD, “MB4x Responder media”, in the FDD and power on the computer. When OS is booted, the ...
Page 172 - procedure
3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Atheros) 3-64 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.26.2 Test procedure 1. Boot the DUT PC by the FD, “MB4x/MB5x boot media”. The following message is displayed. ************************************************************ ...
Page 174 - Contents of Test; SKU check of Module
3 Tests and Diagnostics 3.26 Wireless LAN Test Program (Atheros) 3-66 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.26.3 Contents of Test 1. SKU check of Module This displays the destination information of the wireless LAN module as follows: *********************************************...
Page 175 - Error messages and the contents
3.26 Wireless LAN Test Program (Atheros) 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-67 4. Communication test of 11g mode Communication test of 11g mode Communication test of 11g mode (Main Antenna only) This checks the antenna connection in 11g mode and transm...
Page 177 - LAN; To execute LAN test, press; Press the number you want to test and press
3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-69 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program This section describes how to perform the LAN/Modem/Bluetooth/IEEE1394 test with the test program. Insert the test progr...
Page 178 - NG; message will appear in the display.
3 Tests and Diagnostics 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program Subtest01 (i82562 + ICHx) NOTE: (i82562 + ICHx) test is not supported in this model. This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. The following message will appear. [LAN transmit & recei...
Page 179 - 000Base Auto-negotiation TxRx Test
3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics Subtest02 (GbE) This subtest checks the operation of mini-PCI I/F by the loopback test in the chip. Select 2 to execute and press Enter . The following message will appear. Testing adapter...hit <ESC> to abort. * External L...
Page 180 - test; To execute Modem test, press; * Scorpio Modem Initialize; If the color in the LED of the connection checker is orange, press
3 Tests and Diagnostics 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-72 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3.27.2 Modem test For this subtest, connect the modem PCB and RJ11 connector with a harness. Use the dedicated “FAT-MODE inspection device (product code: QE2000P01 mad...
Page 181 - To execute this test, input; NOTE: This model does not support the Bluetooth test.; Bluetooth sub system test program VX.XX; or
3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-73 3.27.3 Bluetooth test To execute this test, input 3 and press Enter . NOTE: This model does not support the Bluetooth test. NOTE: Use another computer that can communi...
Page 182 - . The following message
3 Tests and Diagnostics 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-74 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Subtest01 BD_ADDR check This subtest checks the BD_ADDR functions. When the Bluetooth test menu is displayed, press 1 to select the test and press Enter . The followin...
Page 183 - Message Contents
3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-75 If the target machine has any problem, it displays Error message. The following message is displayed. -----------------------------------------------------------------...
Page 185 - Subtest T; of the responder machine. The
3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-77 Table 3-6 Error code for Bluetooth test (BD_ADDR) (2/2) Error code Meaning 0x20 Unsupported LMP Parameter Value. 0x21 Role Change Not Allowed. 0x22 LMP Response Timeou...
Page 187 - to select the subtest. The following message will; Space; to start the Bluetooth communication test.
3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-79 Insert a floppy disk containing the test program into the tester machine and turn on the power. When the Bluetooth test menu is displayed on the tester machine, press ...
Page 188 - FAIL
3 Tests and Diagnostics 3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3-80 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) If the DUT machine has any problem or S of the DUT machine is pressed before connection to tester machine, the following message “ INCOMPLETE ” is displayed. ---------...
Page 191 - Subtest02 (Responder
3.27 LAN/Modem/Bluetooth/IEEE1394 Test Program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-83 3.27.4 IEEE1394 test To execute this test, input 4 and press Enter . NOTE: Use another computer that can communicate by IEEE1394 (i. Link) cable as a reference machine...
Page 192 - Sound Test program; Input the test number and press; . The following menu will appear in; Exit to Main
3 Tests and Diagnostics 3.28 Sound Test program 3-84 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 3 Tests and Dia tics 3.28 Sound Test program gnos This section describes how to perform the Sound test. To execute the sound test, refer to the following description. Insert the test program...
Page 193 - . Then following message will appear in; Loading
3.28 Sound Test program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-85 To return to the Sound test menu, Press 9 and Enter . Then following message will appear in the display. *********************************** ******** May I Restart ? ******* ****************...
Page 197 - CD/DVD TEST IN PROGRESS XXXXXXXX; Select the track number you want to test and press; and press
3.28 Sound Test program 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-89 3.28.3.2 Audio CD Insert an audio CD and the following menu appears in the display. CD/DVD TEST IN PROGRESS XXXXXXXX xxxxxxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] : test end [Ctrl]+[C] : key ...
Page 201 - NOTE: You can press; The Factory Preset Configuration
3.29 SETUP 3 Tests and Diagnostics PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 3-93 Moving Within the SETUP Menu and Changing Values 1. Press Å and Æ to move between the two columns. Press ↑ and ↓ to move between items in a column. Press Fn + ↑ ( PgUp) and Fn + ↓ ( PgDn) to move between...
Page 202 - SETUP Options
3 Tests and Diagnostics 3.29 SETUP SETUP Options The SETUP screen is divided into functionally related groups. This section describes each group and its options. 1. Memory This group of options displays the computer’s memory. (a) Total This field displays the total amount of memory installed and is ...
Page 206 - USB; Pressing; Enabled
3 Tests and Diagnostics 3.29 SETUP 3-98 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) (b) HDD Priority Set the priority of the HDD as a startup device. Built-in HDD → USB The priority is set as built-in HDD → USB (Default) USB → Built-in HDD The priority is set as USB memory → built-in HD...
Page 207 - Alarm Time
3.29 SETUP 3 Tests and Diagnostics 8. Others Whether or not you need to configure the computer with these options depends primarily on the kind of software or peripherals you use. (a) Dynamic CPU Frequency Mode Use this option to choose a setting from the followings. Dynamically Switchable CPU power...
Page 208 - BackSpace
3 Tests and Diagnostics 3.29 SETUP 3-100 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) or BackSpace . Press ↓ to move the cursor to the right and ↑ to move the cursor to the left when you set the date and time. For the Alarm Time , set the time to turn on the power automatically. The “sec...
Page 212 - Replacement Procedures
4 Replacement Procedures 4-ii [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 4
Page 217 - Removing the touch; Chart Notation
4.1 Overview 4 Replacement Procedures 4 4.1 Overview This chapter describes the procedure for removing and replacing the field replaceable units (FRUs) in the PC. It may not be necessary to remove all the FRUs in order to replace one. The chart below provides a guide as to which other FRUs must be r...
Page 218 - Safety precautions
4 Replacement Procedures 4.1 Overview 4-2 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Safety precautions Please read the following safety instructions before disassembling the computer and always follow the instructions while working on the computer. DANGER: 1) Always use the genuine ba...
Page 219 - Before You Begin; Use the designated tools.
4.1 Overview 4 Replacement Procedures PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-3 Before You Begin Take note of the following points before starting work. Always remove the AC adapter and battery pack before commencing any of the procedures. The procedure for removing the battery pa...
Page 220 - Disassembly Procedures; Three main types of cable connector are used.
4 Replacement Procedures 4.1 Overview Disassembly Procedures Three main types of cable connector are used. Pressure plate connector Spring connector Normal pin connector 1. When disconnecting a pressure plate connector, draw the tab on one side of the plastic pressure plate on the connector and pull...
Page 221 - Assembly Procedure
4.1 Overview 4 Replacement Procedures PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-5 Assembly Procedure After the computer has been disassembled and the part that caused the fault has been repaired or replaced, the computer must be reassembled. Take note of the following general points...
Page 222 - Screw Tightening Torque; Use the following torque when tightening screws.
4 Replacement Procedures 4.1 Overview Screw Tightening Torque Use the following torque when tightening screws. CAUTION: Overtightening may damage screws or parts. Undertightening may allow screws to loosen (and possibly fall out) causing a short circuit or other damage. NOTE: To tighten screws quick...
Page 223 - Grip Color; Even numbered length screws: Brown; Screw Notation; Screw shape
4.1 Overview 4 Replacement Procedures Grip Color Some screws have a colored grip area to help you determine the length of the screw. Even numbered length screws: Brown Odd numbered length screws: White Special length screw: Blue “Special length screw” means screws whose length is indicated in an int...
Page 224 - pack; Removing the battery pack; Turn off the power of the computer.; battery latch; in the direction indicated by the arrow and insert your finger; battery pack; Battery latch; Figure 4-1 Removing the battery pack
4 Replacement Procedures 4.2 Battery pack 4.2 Battery pack Removing the battery pack To remove the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: Take care not to short circuit the terminals when removing the battery pack. Similarly, do not drop, knock, scratch, disassemble, ...
Page 225 - Installing the battery pack; battery; fitting to the guides.
4.2 Battery pack 4 Replacement Procedures PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-9 Installing the battery pack To install the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: There is a danger that the lithium ion battery pack may explode if not fitted, oper...
Page 226 - card; card manual or the manuals of the computer system you are using.; eject button; Eject button; Figure 4-2 Removing the PC card; Installing the PC card
4 Replacement Procedures 4.3 PC card/SD card 4.3 PC card/SD card 4.3.1 PC card Removing the PC card To remove the PC card, follow the steps below and refer to Figure 4-2. CAUTION: Insert or remove the PC card in accordance with any instructions in the PC card manual or the manuals of the computer sy...
Page 227 - Figure 4-3 Removing the SD card; Installing the SD card
4.3 PC card/SD card 4 Replacement Procedures 4.3.2 SD card Removing the SD card To remove the SD card, follow the steps below and refer to Figure 4-3. CAUTION: Insert or remove the SD card in accordance with any instructions in the SD card manual or the manuals of the computer system you are using. ...
Page 228 - Expansion Memory module; cause memory access problems.; Removing the Expansion memory module; Turn the computer upside down.; screw; Press the two; latches; outward and remove the; memory module; Memory slot cover; Figure 4-4 Removing the memory module
4 Replacement Procedures 4.4 Expansion Memory module 4.4 Expansion Memory module CAUTION: The power of the computer must be turned off when you remove the memory module. Removing a memory module with the power on risks damaging the module or the computer itself. Do not touch the memory module termin...
Page 229 - Installing the Expansion memory module; Never press hard or bend the memory module.; with the left and right latches.; memory slot cover
4.4 Expansion Memory module 4 Replacement Procedures PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-13 Installing the Expansion memory module To install the expansion memory module, follow the steps below and refer to Figure 4-4. CAUTION: The power must be turned off when you insert the ...
Page 230 - Removing the HDD; data loss or damage to the device.; HDD slot cover; Figure 4-5 Removing the HDD slot cover
4 Replacement Procedures 4.5 HDD 4.5 HDD Removing the HDD To remove the HDD, follow the steps below and refer to Figure 4-5 to 4-7. CAUTION: Take care not to press on the top or bottom of the HDD. Pressure may cause data loss or damage to the device. 1. Remove the following screw and HDD slot cover ...
Page 231 - tab; HDD assembly; Figure 4-6 Removing the HDD assembly; gaskets; Figure 4-7 Removing the HDD
4.5 HDD 4 Replacement Procedures 2. Hold the tab of the HDD assembly and remove the HDD assembly from the connector CN4 of the HD FPC. HDD assembly Tab CN4 Figure 4-6 Removing the HDD assembly 3. Peel off two gaskets from the HDD unit and detach the HDD from the HDD holder . HDD HDD holder Gasket Fi...
Page 232 - Installing the HDD; Stick two gaskets in the position shown below.; Gasket
4 Replacement Procedures 4.5 HDD Installing the HDD To install the HDD, follow the steps below and refer to Figure 4-5 to 4-7. 1. Install the HDD to the HDD holder and stick two gaskets on the HDD unit. CAUTION: 1. When replacing the HDD, be sure to stick gaskets on the HDD unit. 2. Stick two gasket...
Page 233 - Removing the keyboard; frame and do not touch the keytop.; S BIND; Figure 4-8 Removing the keyboard holder
4.6 Keyboard 4 Replacement Procedures 4.6 Keyboard Removing the keyboard To remove the keyboard, follow the steps below and refer to Figure 4-8 and 4-9. CAUTION: As the keytop may fall out, when handling the keyboard always hold it by the frame and do not touch the keytop. 1. Remove the following sc...
Page 234 - Keyboard flexible cable; Figure 4-9 Removing the keyboard; Installing the keyboard
4 Replacement Procedures 4.6 Keyboard 6. Disconnect the keyboard flexible cable from the connector CN3200 on the system board and remove the keyboard . CN3200 Keyboard flexible cable Figure 4-9 Removing the keyboard Installing the keyboard To install the keyboard, follow the steps below and refer to...
Page 235 - Removing the Switch board; Switch cover; Figure 4-10 Removing the switch board
4.7 Switch board 4 Replacement Procedures 4.7 Switch board Removing the Switch board To remove the switch board, follow the steps below and refer to Figure 4-10. 1. Turn over the computer and remove the following screw . • M2 × 8S BIND screw x1 2. Turn the computer face up and open the display. 3. R...
Page 236 - Installing the Switch board
4 Replacement Procedures 4.7 Switch board 4-20 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Installing the Switch board To install the switch board, follow the steps below and refer to Figure 4-10. 1. Connect the switch cable to the connector CN3270 on the system board. 2. Install the sw...
Page 237 - pad; Removing the Touch pad; Remove the; touch pad cover; while releasing the latches.; Touch pad cover; Figure 4-11 Removing the touch pad cover
4.8 Touch pad 4 Replacement Procedures 4.8 Touch pad Removing the Touch pad To remove the touch pad, follow the steps below and refer to Figure 4-11 and 4-12. 1. Remove the touch pad cover while releasing the latches. Touch pad cover Figure 4-11 Removing the touch pad cover PORTEGE R200 Maintenance ...
Page 238 - touch pad cable; Touch pad assembly; Figure 4-12 Removing the touch pad
4 Replacement Procedures 4.8 Touch pad 2. Disconnect the touch pad cable from the connector CN3240 on the system board. 3. Remove the following screws fixing the touch pad assembly. • M2 × 3C S-FLAT HEAD screw x2 4. Remove the touch pad assembly from the palm rest while releasing the adhesive portio...
Page 239 - Installing the touch pad
4.8 Touch pad 4 Replacement Procedures PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-23 Installing the touch pad To install the touch pad, follow the steps below and refer to Figure 4-11 and 4-12. 1. Connect the touch pad cable to the connector on the touch pad assembly. 2. Install the ...
Page 240 - Cover assembly/Battery latch assembly; Removing the Cover assembly/Battery latch assembly; Turn over the computer and remove the following; screws; BIND screw
4 Replacement Procedures 4.9 Cover assembly/Battery latch assembly 4.9 Cover assembly/Battery latch assembly Removing the Cover assembly/Battery latch assembly To remove the cover assembly/battery latch assembly, follow the steps below and refer to Figure 4-13 to 4-15. 1. Turn over the computer and ...
Page 241 - cover; by lifting it up from the base assembly.; Cover assembly
4.9 Cover assembly/Battery latch assembly 4 Replacement Procedures 2. Turn the computer face up and open the display. 3. Remove the following screws . • M2 × 4B S-FLAT HEAD screw x2 4. Remove the cover assembly by lifting it up from the base assembly. M2 × 4B S-FLAT HEAD Cover assembly Figure 4-14 R...
Page 242 - Battery latch assembly; Figure 4-15 Removing the battery latch assembly; Installing the Cover assembly/Battery latch assembly
4 Replacement Procedures 4.9 Cover assembly/Battery latch assembly 5. Remove the following screws and battery latch assembly . • M2 × 2.5B S-FLAT HEAD screw x3 Battery latch assembly M2 × 2.5B S-FLAT HEAD M2 × 2.5B S-FLAT HEAD Figure 4-15 Removing the battery latch assembly Installing the Cover asse...
Page 243 - Bluetooth module; Removing the Bluetooth module; Bluetooth antenna cable; Figure 4-16 Removing the Bluetooth module; Installing the Bluetooth module
4.10 Bluetooth module 4 Replacement Procedures 4.10 Bluetooth module Removing the Bluetooth module To remove the Bluetooth module, follow the steps below and refer to Figure 4-16. 1. Remove the following screw securing the Bluetooth module . • M2 × 3C S-FLAT HEAD screw x1 2. Disconnect the Bluetooth...
Page 244 - Removing the Speaker/Fingerprint sensor board; Speaker; Figure 4-17 Removing the speaker/SP FPC
4 Replacement Procedures 4.11 Speaker/Fingerprint sensor board 4.11 Speaker/Fingerprint sensor board Removing the Speaker/Fingerprint sensor board To remove the speaker/fingerprint sensor board, follow the steps below and refer to Figure 4-17 and 4-18. 1. Remove the following screw and lift up the S...
Page 245 - Fingerprint sensor board; Figure 4-18 Removing the fingerprint sensor board; Installing the Speaker/Fingerprint sensor board
4.11 Speaker/Fingerprint sensor board 4 Replacement Procedures 5. Remove the following screw and fingerprint sensor board . • M2 × 3C S-FLAT HEAD screw x1 M2 × 3C S-FLAT HEAD Fingerprint sensor board Figure 4-18 Removing the fingerprint sensor board Installing the Speaker/Fingerprint sensor board To...
Page 246 - Removing the MDC board; MDC board; Figure 4-19 Removing the MDC board; Installing the MDC board
4 Replacement Procedures 4.12 MDC board 4.12 MDC board Removing the MDC board To remove the MDC board, follow the steps below and refer to Figure 4-19. 1. Remove the following screws and disconnect the MDC board from the connector CN3010 on the MP FPC. • M2 × 3C S-FLAT HEAD screw x2 2. Disconnect th...
Page 247 - Removing the RTC battery; RTC battery; Figure 4-20 Removing the RTC battery; Installing the RTC battery
4.13 RTC battery 4 Replacement Procedures 4.13 RTC battery Removing the RTC battery To remove the RTC battery, follow the steps below and refer to Figure 4-20. 1. Peel off the two glass tapes . 2. Disconnect the RTC battery cable from the connector CN9990 on the system board and remove the RTC batte...
Page 248 - Wireless LAN card; Removing the Wireless LAN card; Latch; Figure 4-21 Removing the Wireless LAN card; Installing the Wireless LAN card
4 Replacement Procedures 4.14 Wireless LAN card 4.14 Wireless LAN card Removing the Wireless LAN card To remove the Wireless LAN card, follow the steps below and refer to Figure 4-21. 1. Disconnect the wireless LAN antenna cables (black and white) from the Wireless LAN card using an antenna coaxial ...
Page 249 - Removing the Fan; Glass tape; Figure 4-22 Removing the fan; Installing the Fan
4.15 Fan 4 Replacement Procedures 4.15 Fan Removing the Fan To remove the fan, follow the steps below and refer to Figure 4-22. 1. Peel off the glass tape and disconnect the fan cable from the connector CN8770 on the system board. 2. Remove the following screws and fan . • M2 × 4C BIND screw x2 Glas...
Page 250 - Removing the MP FPC; HEAD; Figure 4-23 Removing the MP FPC
4 Replacement Procedures 4.16 MP FPC 4.16 MP FPC Removing the MP FPC To remove the MP FPC, follow the steps below and refer to Figure 4-23. 1. Remove the following screw and kill switch holder . • M2 × 3C S-FLAT HEAD screw x1 2. Remove the following screws and disconnect the MP FPC from the connecto...
Page 251 - Installing the MP FPC
4.16 MP FPC 4 Replacement Procedures PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-35 Installing the MP FPC To install the MP FPC, follow the steps below and refer to Figure 4-23. 1. Connect the MP FPC to the connector CN9500 on the system board and secure it with the following screws ....
Page 252 - Removing the HD FPC; Figure 4-24 Removing the HD FPC; Installing the HD FPC
4 Replacement Procedures 4.17 HD FPC 4.17 HD FPC Removing the HD FPC To remove the HD FPC, follow the steps below and refer to Figure 4-24. 1. Peel off the glass tape and disconnect the HD FPC from the connector CN1800 on the system board. Glass tape HD FPC CN1800 Figure 4-24 Removing the HD FPC Ins...
Page 253 - Removing the PC card slot; PC card slot; Figure 4-25 Removing the PC card slot; Installing the PC card slot
4.18 PC card slot 4 Replacement Procedures 4.18 PC card slot Removing the PC card slot To remove the PC card slot, follow the steps below and refer to Figure 4-25. 1. Remove the following screws fixing the PC card slot. • M2 × 4C S-FLAT HEAD screw x2 2. Remove the PC card slot from the connector CN2...
Page 254 - Removing the LAN/Modem jack; LAN cable; Installing the LAN/Modem jack
4 Replacement Procedures 4.19 LAN/Modem jack 4.19 LAN/Modem jack Removing the LAN/Modem jack To remove the LAN/Modem jack, follow the steps below and refer to Figure 4-26. 1. Disconnect the LAN cable from the connector CN4100 on the system board. 2. Remove the LAN/Modem jack from the slot. CN4100 LA...
Page 255 - Removing the System board
4.20 System board 4 Replacement Procedures PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-39 4.20 System board Removing the System board To remove the system board, follow the steps below and refer to Figure 4-27. 1. Disconnect the LCD cable and FL cable from the connectors CN5600 and CN...
Page 256 - Figure 4-27 Removing the system board; Installing the system board; LED cable
4 Replacement Procedures 4.20 System board M2 × 3C S-FLAT HEAD System board Audio cover 4-40 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Figure 4-27 Removing the system board Installing the system board To install the system board, follow the steps below and refer to Figure 4-27. 1. Ins...
Page 257 - Internal microphone; Removing the Internal microphone; Microphone cable; Figure 4-28 Removing the internal microphone; Installing the Internal microphone
4.21 Internal microphone 4 Replacement Procedures 4.21 Internal microphone Removing the Internal microphone To remove the internal microphone, follow the steps below and refer to Figure 4-28. 1. Disconnect the microphone cable from the connector CN6050 on the system board. 2. Remove the internal mic...
Page 258 - Removing the LED FPC; To remove the LED FPC, follow the steps below and refer to Figure 4-29.; LED FPC; Figure 4-29 Removing the LED FPC; Installing the LED FPC; Install the; LED FPC; according to the guide and secure it with the following
4 Replacement Procedures 4.22 LED FPC 4.22 LED FPC Removing the LED FPC To remove the LED FPC, follow the steps below and refer to Figure 4-29. 1. Remove the following screws and LED FPC . • M2 × 3C S-FLAT HEAD screw x2 M2 × 3C S-FLAT HEAD LED FPC Figure 4-29 Removing the LED FPC Installing the LED ...
Page 259 - Removing the Display mask; Figure 4-30 Removing the display mask
4.23 Display mask 4 Replacement Procedures 4.23 Display mask Removing the Display mask To remove the display mask, follow the steps below and refer to Figure 4-30. 1. Peel off the six mask seals and four LCD cushions on the LCD mask and remove the following screws . • M2 × 3.2S FLAT HEAD screw x8 (“...
Page 260 - Installing the Display mask
4 Replacement Procedures 4.23 Display mask 4-44 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Installing the Display mask To install the display mask, follow the steps below and refer to Figure 4-30. 1. Install the display mask while engaging the latches. 2. Secure the following screws to...
Page 261 - Removing the FL inverter/LCD unit; FL inverter; Figure 4-31 Removing the FL inverter
4.24 FL inverter/LCD unit 4 Replacement Procedures 4.24 FL inverter/LCD unit Removing the FL inverter/LCD unit To remove the FL inverter/LCD unit, follow the steps below and refer to Figure 4-31 and 4-32. 1. Remove the following screw fixing the FL inverter. • M2 × 3C S-FLAT HEAD screw x1 2. Peel th...
Page 262 - glass tape; Disconnect the; LCD cable; and remove the; LCD unit; Figure 4-32 Removing the LCD unit
4 Replacement Procedures 4.24 FL inverter/LCD unit 4. Carefully lift up the top of the LCD unit and peel off the glass tape . 5. Disconnect the LCD cable and remove the LCD unit . Glass tape LCD cable LCD unit Figure 4-32 Removing the LCD unit 4-46 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960...
Page 263 - Installing the FL inverter/LCD unit
4.24 FL inverter/LCD unit 4 Replacement Procedures PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-47 Installing the FL inverter/LCD unit To install the FL inverter/LCD unit, follow the steps below and refer to Figure 4-31 and 4-32. 1. Set the LCD unit to the display cover in place. 2. Co...
Page 264 - Removing the Hinge; Remove the following; Hinge cap; Figure 4-33 Removing the hinge cap
4 Replacement Procedures 4.25 Hinge 4.25 Hinge Removing the Hinge To remove the hinge, follow the steps below and refer to Figure 4-33 to 4-35. 1. Remove the following screws (back) and hinge caps (left and right). • M2 × 3C S-FLAT HEAD screw x2 M2 × 3C S-FLAT HEAD M2 × 3C S-FLAT HEAD Hinge cap Hing...
Page 265 - FLAT HEAD screw; B FLAT HEAD; Figure 4-34 Removing the palm rest
4.25 Hinge 4 Replacement Procedures 2. Remove the following screws (back) and palm rest . • M2.5 × 4B FLAT HEAD screw x4 M2.5 × 4B FLAT HEAD M2.5 × 4B FLAT HEAD Palm rest Figure 4-34 Removing the palm rest PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-49
Page 266 - hinges; BIND; Figure 4-35 Removing the hinge
4 Replacement Procedures 4.25 Hinge 3. Take out the LCD cable from the hole. 4. Remove the following screws and hinges of the both sides. • M3 × 3S BIND screw x2 • M2 × 4B S-FLAT HEAD screw x2 LCD cable Hinge Hinge M3 × 3S BIND M3 × 3S BIND M2 × 4B S-FLAT HEAD M2 × 4B S-FLAT HEAD Figure 4-35 Removin...
Page 267 - Installing the hinge
4.25 Hinge 4 Replacement Procedures PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] 4-51 Installing the hinge To install the hinge, follow the steps below and refer to Figure 4-33 to 4-35. 1. Install the both sides’ hinges and secure them with the following screws . • M3 × 3S BIND screw x2 ...
Page 268 - Wireless LAN antenna/Bluetooth antenna; Removing the Wireless LAN antenna; Figure 4-36 Removing the wireless LAN antenna; Installing the Wireless LAN antenna
4 Replacement Procedures 4.26 Wireless LAN antenna/Bluetooth antenna 4.26 Wireless LAN antenna/Bluetooth antenna 4.26.1 Wireless LAN antenna Removing the Wireless LAN antenna To remove the wireless LAN antenna, follow the steps below and refer to Figure 4-36. 1. Peel off the six acetate tapes on the...
Page 269 - Removing the Bluetooth antenna; Acetate tape; Figure 4-37 Removing the Bluetooth antenna; Installing the Bluetooth antenna
4.26 Wireless LAN antenna/Bluetooth antenna 4 Replacement Procedures 4.26.2 Bluetooth antenna Removing the Bluetooth antenna To remove the Bluetooth antenna, follow the steps below and refer to Figure 4-37. 1. Peel off the five acetate tapes on the display cover. 2. Peel off the Bluetooth antenna fr...
Page 270 - Fluorescent Lamp; This system uses LCD modules from the following supplier.; Supplier Section; soiling or scratching the LCD panel.
4 Replacement Procedures 4.27 Fluorescent Lamp 4-54 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) 4.27 Fluorescent Lamp This system uses LCD modules from the following supplier. Type Part.No Supplier Section 12.1 inch G33C0002C110 TMD 4.27.1 NOTE: - When working with a LCD module, always ...
Page 271 - Replacing the 12.1 Inch TMD fluorescent lamp; Disassembling the module
4.27 Fluorescent Lamp 4 Replacement Procedures 4.27.1 Replacing the 12.1 Inch TMD fluorescent lamp The following describes the procedure for replacing the fluorescent lamp (See Figure 4-38 to 4-47). Disassembling the module 1. Peel off tapes and insulating sheets. 1) Place carefully the module face ...
Page 275 - Cell
4.27 Fluorescent Lamp 4 Replacement Procedures 5. Removing the cell with the PCB 1) Remove the cell with the PCB from the backlight unit as shown in the figure below. CAUTION: 1) Peel off the cell carefully not to break it. 2) Be careful not to damage the TAB. Cell Figure 4-42 Replacing Toshiba fluo...
Page 277 - Cell with PCB
4.27 Fluorescent Lamp 4 Replacement Procedures 2. Assembling the cell with the PCB 1) Illuminate the backlight. 2) Make sure there is no scratch or dirt on the backlight. Also check the back of the cell. Next, install the cell with the PCB to the backlight unit. CAUTION: 1) Install by aligning the l...
Page 283 - Appendix Contents; System Board
Appendices PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] App-iii Appendix Contents Appendix A Handling the LCD Module......................................................................... A-1 Appendix B Board Layout..........................................................................
Page 284 - SP FPC; Appendix I
Appendices App-iv [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) C.19 CN8800 DC-IN Connector (2pin) ..............................................................C-14 C.20 CN8810 1 st Battery Connector (10pin) .......................................................C-15 C.21 CN8770 Fan Conn...
Page 286 - Tables
Appendices App-vi [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Tables Table B-1 System board (front) .....................................................................................B-2 Table B-2 System board (back) .......................................................................
Page 289 - Appendix A Handling the LCD Module; Precautions for handling the LCD module
Appendix A Handling the LCD Module Appendices Apx. A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in th...
Page 290 - PORTEGE
Appendices Appendix A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent...
Page 295 - Appendix B Board Layout; B.1 System board Front View
Appendix B Board Layout Appendices Apx. B Appendix B Board Layout B.1 System board Front View Figure B-1 System board layout (front) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] B-1
Page 296 - Mark Number
Appendices Appendix B Board Layout B-2 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Table B-1 System board (front) Mark Number Name (A) CN5620 External CRT Connector (B) CN6050 Internal Microphone connector (C) CN8800 DC-IN Connector (D) CN4610 USB 0 Connector (E) CN4611 USB 3 Connector ...
Page 297 - B.2 System board Back View
Appendix B Board Layout Appendices B.2 System board Back View Figure B-2 System board layout (Back) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] B-3
Page 303 - Appendix C Pin Assignment; Signal name
Appendix C Pin Assignment Appendices PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] C-1 Apx. C Pin Assignment Appendix C Pin Assignment System Board C.1 CN1400 SO-DIMM0 connector (200pin) Table C-1 SO-DIMM0 connector (200pin)(1/4) Pin No. Signal name I/O Pin No. Signal Name I/O 1 MRVREF-B0...
Page 315 - CN6050 Internal Microphone Connector (2pin)
Appendix C Pin Assignment Appendices PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] C-13 C.14 CN5601 FL Inverter Connector (8pin) Table C- 14 FL Inverter Connector (8pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 FL-P5V O 2 FL-P5V O 3 GND - 4 GND - 5 BKLPWM-P2P O 6 FL-P5V - 7 FL-P5...
Page 322 - MP FPC
Appendices Appendix C Pin Assignment C-20 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) MP FPC C.29 CN2200 MINI PCI I/F Connector (124pin) Table C- 29 MINI PCI I/F Connector (124pin) (1/3) Pin No. Signal name I/O Pin No. Signal name I/O 1 N.C. - 2 N.C. - 3 N.C. - 4 N.C. - 5 N.C. - 6 N.C. ...
Page 327 - FS Board
Appendix C Pin Assignment Appendices PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] C-25 FS Board C.32 CN950 SP FPC I/F Connector (6pin) Table C- 32 SP FPC I/F Connector (6pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 GND - 2 USBFS-S3P I/O 3 USBFS-S3N I/O 4 GND - 5 FGSPON-S3N I 6 ...
Page 329 - Appendix D Keyboard Scan/Character Codes
Appendix D Keyboard Scan/Character Codes Appendices PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] D-1 Apx. D Keyboard Scan/Character Codes Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note ...
Page 332 - key makes different codes.; Fn; key does not generate a code by itself.
Appendices Appendix D Keyboard Scan/Character Codes D-4 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Table D-1 Scan codes (set 1 and set 2) (4/4) Code set 1 Code set 2 Cap No. Keytop Make Break Make Break Note 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6...
Page 333 - Shift
Appendix D Keyboard Scan/Character Codes Appendices PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] D-5 Table D-2 Scan codes with left Shift key Code set 1 Code set 2 Cap No. Key top Make Break Make Break 55 / E0 AA E0 35 E0 B5 E0 2A E0 F0 12 E0 4A E0 F0 4A E0 12 75 INS E0 AA E0 52 E0 D2 E0...
Page 334 - Code set 1
Appendices Appendix D Keyboard Scan/Character Codes D-6 [CONFIDENTIAL] PORTEGE R200 Maintenance Manual (960-519) Table D-3 Scan codes in Numlock mode Code set 1 Code set 2 Cap No. Key top Make Break Make Break 75 INS E0 2A E0 52 E0 D2 E0 AA E0 12 E0 70 E0 F0 70 E0 F0 12 76 DEL E0 2A E0 53 E0 D3 E0 A...
Page 337 - Appendix E Key Layout
Appendix E Key Layout Appendices Apx. E Key Layout Appendix E Key Layout Figure E-1 Key layout (UK) Figure E-2 Key layout (US) PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] E-1
Page 339 - Appendix F Wiring diagrams; F.1 LAN Loopback Connector; Figure F-1 LAN loopback connector
Appendix F Wiring diagrams Appendices Appendix F Appendix F Wiring diagrams F.1 LAN Loopback Connector Figure F-1 LAN loopback connector PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] F-1
Page 341 - Appendix G BIOS rewrite procedures; Tools
Appendix G BIOS rewrite procedures Appendices Appendix G Appendix G BIOS rewrite procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool: BIOS/EC/KBC rewriting disk for the computer that has re...
Page 343 - Appendix H EC/KBC rewrite procedures; BIOS/EC/KBC rewriting disk for the computer; Tab
Appendix H EC/KBC rewrite procedures Appendices PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] H-1 Appendix H Appendix H EC/KBC rewrite procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system. Tools To rewrite the EC/KBC, you need the fo...
Page 345 - Component Time
Appendix I Reliability Appendices PORTEGE R200 Maintenance Manual (960-519) [CONFIDENTIAL] I-1 Apx. I Reliability Appendix I Reliability The following table shows MTBF (Mean Time Between Failures) for each component. Table I-1 MTBF Component Time (hours) System 5,789