Page 2 - PREVENTATIVE MAINTENANCE
PREVENTATIVE MAINTENANCE PREVENTATIVE MAINTENANCE Toshiba copiers are manufactured to the highest technical standards, using quality parts andcomponents, and are designed to meet all electrical safety and environmental requirements. To ensure that optimum levels of performance and reliability are ma...
Page 3 - Storage of Colour Copies
Storage of Colour Copies (1) The copies should be kept in a place which is not exposed to light to prevent fading when they are stored for a long time. (2) If copies are kept pressed between plastics made of chloroethylene for a long time, the toner may melt and stick to the plastic due to high pres...
Page 4 - Forgery Prevention Function
Forgery Prevention Function This copier has a forgery prevention function. Please ensure that your digital full colour copier is not used for making copies of prohibiteditems.
Page 5 - PREFACE
1 PREFACE CONTENTS PRECAUTIONS PREFACE Thank you for purchasing the Toshiba Digital Colour Copier FC15/22. This Operator’s Manual describesthe following: • how to use the digital colour copier• how to inspect and carry out maintenance on the digital copier• how to remedy mechanical and copying probl...
Page 7 - TABLE OF CONTENTS
3 TABLE OF CONTENTS DESCRIPTION OF THE DIGITAL COPIER HOW TO MAKE COPIES COLOR EDITING AND ADJUSTMENT USING THE EDITING FUNCTIONS USING THE SPECIAL FUNCTIONS USING THE OPTIONAL SORTER WHEN THE GRAPHIC SYMBOLS FLASH MAINTENANCE SPECIFICATIONS, ACCESSORIES & OPTIONS PREFACE CONTENTS PRECAUTIONS ■ ...
Page 9 - PRECAUTIONS
5 PREFACE CONTENTS PRECAUTIONS PRECAUTIONS 1. INSTALLATION The copier should be located near a wall outlet which should be easily accessible. 3 2 1 The FC15/22 should be installed by a qualified service technician. Note: The packing material should be disposed of properly. To obtain the best possibl...
Page 10 - GENERAL PRECAUTIONS
6 2 1 3 2. GENERAL PRECAUTIONS Handle and use the copier gently and carefully. Do not place anything on the paper cassettes or original feed tray. Never allow the power cable to be trampled on or pinched between hard objects, otherwisean accident or electrical trouble might occur. Do not allow any m...
Page 11 - DESCRIPTION OF THE DIGITAL COPIER
7 DESCRIPTION OF THE DIGITAL COPIER 1. DESCRIPTION OF THE DIGITAL COPIER 1. Names of the Main Components . . . . . . . . . . . 8 2. Description of the Optional Equipment . . . . . . 9 3. Description of the Control Panel . . . . . . . . . . . 10 4. Description of the Message Display . . . . . . . . 1...
Page 12 - NAMES OF THE MAIN COMPONENTS
8 Toner cartridge Right-hand front cover Left-hand front cover Used toner bag Transfer belt unit knob Fuser unit Explanatory Label Transfer belt unit Electrophotographic unit Operator's manual pocket(Back side) CLASS 1 LASER PRODUCTLASER KLASSE 1APPAREIL A LASER DE CLASSE 1 Original scale Control pa...
Page 13 - DESCRIPTION OF THE OPTIONAL EQUIPMENT
9 DESCRIPTION OF THE DIGITAL COPIER 3 Staple sorter 2 Automatic duplexer 4 Large-capacity feeder 5 Key copy counter 1 Reversing automatic document feeder Original feed tray 2. DESCRIPTION OF THE OPTIONAL EQUIPMENT 1 Reversing Automatic Document Feeder A set of originals can automatically be fed one ...
Page 14 - DESCRIPTION OF THE CONTROL PANEL
10 3. DESCRIPTION OF THE CONTROL PANEL q MECHANICAL COUNTER T h e t o t a l n u m b e r o fcopies (converted intoLetter size) made after theinstallation of the copieris shown here. w TIMER lamp This lamp lights duringthe use of the timer. e INFO key Use this key to display thea p p r o p r i a t e o...
Page 17 - DESCRIPTION OF THE MESSAGE DISPLAY
13 DESCRIPTION OF THE DIGITAL COPIER The Message Display panel shows the operation state,error messages and function menus. 䢇 Each icon displayed is shown in the form of a touch key.You can select the function by touchingthe key lightly with your finger. 䢇 Turning ON the power switch will show the B...
Page 19 - DESCRIPTION OF THE GRAPHIC DISPLAY; i u
15 DESCRIPTION OF THE DIGITAL COPIER q CHECK ORIGINAL symbol This symbol flashes when an original is misfedinside the automatic document feeder. (Page 147) w BYPASS MISFEED symbol This symbol flashes when no paper is fed into thecopier in bypass copying. Remove and reset thesheets on the sheet bypas...
Page 20 - MEMO
Page 21 - HOW TO MAKE COPIES; Using the Reversing Automatic
17 HOW TO MAKE COPIES 2. HOW TO MAKE COPIES 1. Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2. Energy-Saving Function . . . . . . . . . . . . . . . . . . 20 3. Turning ON the Power Switch/ Auto Job Start . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4. Using th...
Page 22 - Acceptable Paper Types and Sizes
18 1. PAPER Acceptable Paper Types and Sizes Refer to the list below for the acceptable paper. Use the recommended paper for optimum copy quality. Feeder 1stCassette 2ndCassette 3rdCassette 4thCassette SheetBypass Large-CapacityFeeder Paper Type Plain paper Plain paper THICK1(91-105g/m 2 ) OHP film ...
Page 24 - Forcibly Switching to Energy-saving Mode
20 2. ENERGY-SAVING FUNCTION * Power consumption during normal standby : approx. 284W ● Level 1 is set as the default mode. You canswitch the initial mode depending on user'senvironment (see page 119). The energy-saving function is to save the power consumption by lowering the fuser temperaturewhile...
Page 25 - TURNING ON THE POWER SWITCH / AUTO JOB START; Turning ON the Power Switch
21 HOW TO MAKE COPIES 1 2 3. TURNING ON THE POWER SWITCH / AUTO JOB START Turn ON the power switch. Turning ON the Power Switch ● The following message appears. Wait Warming Up About 9 minutes later, the message “READY” appears. ● This message indicates that you can makecopies at any time. ● If this...
Page 26 - Auto Job Start
22 3. TURNING ON THE POWER SWITCH / AUTO JOB START (Cont.) If you set the desired copying modes and press the START key during warm-up, the copierautomatically starts copying when it becomes READY. Place the original(s) on the original feed tray or on the glass. ● After aligning the edges of the ori...
Page 28 - Precautions When Feeding Originals
24 The optional Reversing Automatic Document Feeder automatically feeds and copies sheetpaper originals placed on the feeding tray one at a time. This is called the “continuous feedmode.” You can also manually feed originals in one sheet at a time. This is called the “singlefeed mode.” If you feed i...
Page 29 - Copying in the Continuous Feed Mode
25 HOW TO MAKE COPIES Copying in the Continuous Feed Mode 12 Press the ADF key on the panel to select continuous feed. ● ADF is highlighted and selected as the defaultfeed mode. ● The panel returns to the original display. 3 5 Slides 6 Press the PROGRAM key on the display panel. Press the ADF key. S...
Page 30 - Copying in the Single-Feed Mode
26 Press the PROGRAM key on the display panel. 1 Copying in the Single-Feed Mode 2 Press the ADF key. 3 4 5 Press the SADF key on the panel to select single feeding. ● SADF is highlighted and selected. ● The touch panel returns to the original display. Select the desired copy size, reproduction rati...
Page 31 - Copying in the Mixed Originals Mode
27 HOW TO MAKE COPIES Press the PROGRAM key on the display panel. 12 Press the MIXED ORIGINAL SIZES key. 4 5 3 Press the SET key . Select the Automatic Paper Selection (APS) mode or Automatic Magnification Selection (AMS) mode. Then select the desired copy size, reproduction ratio, image density lev...
Page 32 - COPYING IN THE AUTOMATIC PAPER SELECTION MODE; Procedure
28 When the power switch is turned ON, the Automatic Paper Selection (APS) mode is selectedas the default mode.In this mode, if you place an original on the document feeder or on the glass, the copierautomatically detects the size of the original, and selects paper of the same size as the original.T...
Page 35 - When the Automatic Paper Selection is not Available
31 HOW TO MAKE COPIES 3 Press the START key. 4 Tip: If there are sheets of paper set on thesheet bypass, you must press the COPY-SIZE key corresponding to the sheets.See page 41. Return to the Basic menu, then select the image density level and copy quantity as required. 1 Place the original(s) on t...
Page 36 - Using Automatic Magnification Selection; REDUCTION AND ENLARGEMENT COPYING
32 There are three methods available for enlargement and reduction copying. ● Using Automatic Magnification Selection (AMS):After selecting the AMS mode and the copy size, when you place an original on the glassor when an original is fed from the reversing automatic document feeder, the copierautoma...
Page 38 - Selecting the Original Size and the Copy Size
34 1 Selecting the Original Size and the Copy Size 3 4 Press the ZOOM ORG. A4 KEY. Press the desired COPY-SIZE key. ● The copier calculates the correct reproductionratio based on the selected original size andcopy size, and displays the reproduction ratioon the reproduction-ratio display.(See page 1...
Page 39 - Using the Zoom Keys
35 HOW TO MAKE COPIES 4 Select the desired image density level and copy quantity if required. 1 Using the Zoom Keys 3 Press the Up or Down key to select the desired reproduction ratio. ● For enlargement, use the UP key. Forreduction, use the DOWN key. ● Each time you press either ZOOM key, thereprod...
Page 40 - COPYING WITH COPY DENSITY SELECTION; Copying in Manual Density Mode
36 7. COPYING WITH COPY DENSITY SELECTION There are two modes of adjusting the image density and background level of the copy.In the manual copy density mode, you can produce lighter or darker copies.In the automatic copy density mode, the copier automatically detects the density of the original,and...
Page 41 - Copying in Automatic Density Mode
37 HOW TO MAKE COPIES 1 Press the START key. ● The copier automatically detects the densityof the original, and makes copies at theoptimum image density and background level. 4 Copying in Automatic Density Mode Press the AUTO key. Place the original(s) on the original feed tray or on the glass. ● Se...
Page 42 - COPYING BY ORIGINAL MODE SELECTION
38 Note: In the Advance Image Enhancementmode, the patterns of originals arerecognized during copying, so the copyingspeed becomes slower. You can select the copy mode (Text/Photo, Text, Printed Image, Photo, Map or Advanced Image)and produce clear copies matched to the type of original.* Advance Im...
Page 44 - Selecting the Colour Mode
40 9. COLOUR MODE Tips: ● In the AUTO COLOUR mode, the colours oforiginals are recognized during copying, sothe copying speed becomes slower. ● In the AUTO COLOUR mode,if the colour areais too small or the colours are close to blackor they are too light, colour originals may becopied in black. In th...
Page 51 - CASSETTE SETTING FOR THICK PAPER/OHP FILM
47 HOW TO MAKE COPIES Thick paper with a weight of 91~105g/m 2 can be fed from the cassette or large-capacity feeder, and OHP film can be fed from the cassette. This is convenient if copies are often made onspecial paper. 2 3 11. CASSETTE SETTING FOR THICK PAPER/OHP FILM Press the PROGRAM key to ent...
Page 52 - Setting the Cassette for OHP Film
48 1 3 Pull out the second cassette slowly until comes to a stop. ● Only the 2nd cassette is available for settingthe cassette for OHP films. Take out the size mark plate of the cassette and set that of the OHP film. ● "OHP FILM" is shown in the paper size indicator. Setting the Cassette for...
Page 53 - When the Controller (optional) is installed; INTERRUPT COPYING
49 HOW TO MAKE COPIES When the Controller (optional) is installed Interrupt Copying during Printing If you press the COPY JOB REQUEST key while the printer is being used, interrupt copying becomes available when the current printing job is completed. The screen on the right appears during printing. ...
Page 55 - COLOUR EDITING AND ADJUSTMENT
51 COLOR EDITING AND ADJUSTMENT 3. COLOUR EDITING AND ADJUSTMENT 1. Monocolour Copying . . . . . . . . . . . . . . . . . . . . . 52 2. Hue Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 53 3. Saturation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 4. Colour Balance (YMC...
Page 56 - MONOCOLOUR COPYING
52 1. MONOCOLOUR COPYING You can select one colour out of 10 colours of the colour sample seal to make a monocolourcopy. 1 Procedure 2 3 Press the START key. 4 Press the COLOUR key to enter the colour menu, then press the MONOCOLOUR key. Press the desired copy colour key. ● Press the MAGENTA key for...
Page 57 - Cancelling the Hue Adjustment
53 COLOR EDITING AND ADJUSTMENT 2. HUE ADJUSTMENT This function is available to adjust the hue by changing the hue circle. 1 2 Procedure Press the COLOUR key to enter the colour menu, then press the HUE/SATURATION key. Press the HUE key, then the + or – key to adjust the hue. ● Pressing the + key br...
Page 58 - Cancelling the Saturation Adjustment
54 3. SATURATION This function allows you to adjust the saturation of copies. 1 2 Procedure Press the COLOUR key to enter the colour menu, then press the HUE/SATURATION key. Press the SATURATION key, then the + or – key to adjust the saturation. ● Pressing the + key increases the brightnesswhile pre...
Page 59 - Cancelling the Colour Balance Adjustment
55 COLOR EDITING AND ADJUSTMENT 4. COLOUR BALANCE (YMCK ADJUSTMENT) This function allows you to adjust the colour balance of copies by changing the strength of the primarycolours (Yellow (Y), Magenta (M), Cyan (C) and Black (K)). 1 2 Procedure Press the COLOUR key to enter the colour menu, then pres...
Page 62 - Cancelling the Background Adjustment; BACKGROUND ADJUSTMENT
58 This function allows you to emphasize the background of light colour originals or to avoid copyingthe background of dark colour originals or rear side of originals.This function is available in the black or monocolour mode as well.* Automatic density mode is not available with this function. 1 2 ...
Page 63 - SHARPNESS ADJUSTMENT; Cancelling the Sharpness Adjustment
59 COLOR EDITING AND ADJUSTMENT 8. SHARPNESS ADJUSTMENT This function is available when you want to emphasize the letters and edges of images.This function is available in the black or monocolour mode as well. 1 2 Procedure Press the COLOUR key to enter the colour menu, then press the SHARPNESS key....
Page 65 - USING THE EDITING FUNCTIONS
USING THE EDITING FUNCTIONS 61 4. USING THE EDITING FUNCTIONS 1. Image Shift Copying . . . . . . . . . . . . . . . . . . . . . 62 2. Edge Erase Copying . . . . . . . . . . . . . . . . . . . . . 64 3. Book Centre Erase . . . . . . . . . . . . . . . . . . . . . . 66 4. Dual-page Copying . . . . . . . ...
Page 66 - IMAGE SHIFT COPYING
62 1. IMAGE SHIFT COPYING You can create margins on the copy. You can specify the position of these margins on eitherthe right or the left side of the copy. You can also create margins on copies of book originalsby just using the DUAL PAGE mode. 1 2 Procedure Press the EDIT key to enter the Edit men...
Page 68 - EDGE ERASE COPYING
64 How to Change the Edge Erase Margin ● The default edge erase margin is 5mm. ● To change the edge erase margin, press the 2mm or 20mm key to select the desired edge erase margin. ● If the setting is OK, press the SET key. 2. EDGE ERASE COPYING If the edges of an original are torn or dirty, they ar...
Page 74 - FULL IMAGE COPYING; Copying Procedure
70 5. FULL IMAGE COPYING Press the EDIT key to enter the Edit menu. 2 Press the FULL IMAGE key. ● The image is automatically reduced by a fewpercent so that the entire image is copied ona sheet. Copying Procedure 3 When the image occupies the entire original (to the edge), this function reduces the ...
Page 75 - IN 1 MODE COPYING
USING THE EDITING FUNCTIONS 71 6. 2 IN 1 MODE COPYING When you set A4 sized originals on the original feed tray and select the 2 in 1 function, thecopier automatically feeds in the originals two at a time and causes them to be copied ontoa single sheet of paper. If you select the 2 in 1 duplex mode,...
Page 77 - Duplexed Copies from Single-sided Originals
USING THE EDITING FUNCTIONS 73 2 Press the 1 → 2 key to select the function of single-sided originals to double-sided copies. 7. DUPLEX COPYING There are three methods of making duplexed copies from single-sided originals: • Using the reversing automatic document feeder (optional) – For duplex-copyi...
Page 81 - Duplexed Copies from Two-sided Originals
USING THE EDITING FUNCTIONS 77 Select the desired copy size, reproduction ratio, image density level, copy quantity, etc. if necessary. ● The maximum number of copies is asshown below. 80g/m 2 : 50 (all sizes) 90g/m 2 : 40 (all sizes) 3 4 Place the originals. ● See page 22 for how to set the origina...
Page 82 - Single-sided Copies from Two-sided Originals
78 Copy Copy Original 1 Press the 1 → 1 key on the Basic menu. Press the 2 → 1 key. 2 3 Single-sided Copies from Two-sided Originals 3 Select the desired copy size, reproduction ratio, image density level, copy quantity, etc. if necessary. ● The maximum number of copies is as shownbelow. 0 80g/m 2 :...
Page 83 - Duplexed Copies from Book Originals
USING THE EDITING FUNCTIONS 79 4 Duplexed Copies from Book Originals The copies made will be arranged in the same page order as the book. Notes: • This copying mode requires the optional automatic duplexer to be installed. Notes: • Duplex copying can be made in the plain paper (64~90g/m 2 ) mode onl...
Page 88 - Specifying an area
84 9. TRIMMING/MASKING (Cont.) 1 Specifying an area X2 X1 Y2 Y1 Rear scale Original scale Place the original face up on the glass with its bottom edge towards you and its top left aligned against the top left of the glass. Align the original with the original scale on the left.
Page 91 - Example of mirror image
87 USING THE EDITING FUNCTIONS 10. MIRROR IMAGE This function allows you to make mirror-imaged copies of the entire original. Example of mirror image Procedure 1 34 Place the original(s) on the original feed tray or on the glass and press the START key. ● See page 22 for how to set the originals. 5 ...
Page 97 - USING THE SPECIAL FUNCTIONS; Change of Language on the Display Panel . 118
USING THE SPECIAL FUNCTIONS 93 5. USING THE SPECIAL FUNCTIONS 1. Automatic Calibration . . . . . . . . . . . . . . . . . . . . 94 2. Setting the Date and Time . . . . . . . . . . . . . . . . 97 3. Weekly Timer . . . . . . . . . . . . . . . . . . . . . . . . . . 99 4. Mode Memory . . . . . . . . . . ...
Page 98 - AUTOMATIC CALIBRATION
94 1. AUTOMATIC CALIBRATION This function allows the copier to automatically calibrate the colour gradation when the colourcannot be adjusted well because the shading or the hue of the image has deviated.• Set the A3-sized paper in the cassette before starting the calibration.• Be sure to use the pa...
Page 101 - SETTING THE DATE AND TIME
USING THE SPECIAL FUNCTIONS 97 2. SETTING THE DATE AND TIME With the digital keys, dates and times of the copier‘s internal clock can easily be set consistentwith the current date and time. Press the PROGRAM key to enter the Programme menu. Press the Next key and then the DATE/TIME key. 1 2 Key in t...
Page 103 - Setting the Weekly Timer
USING THE SPECIAL FUNCTIONS 99 3. WEEKLY TIMER The weekly timer, which is incorporated in the copier, is a feature for turning ON and OFF thecopier automatically at the desired times specified. If you set the timer for the start time inthe morning and the end time in the evening of your office, the ...
Page 104 - Cancelling Operation of the Weekly Timer
100 Cancelling Operation of the Weekly Timer You can cancel operation of the weekly timer so that the copier can be turned ON and OFFas normal by the power switch. 1 Check that the WEEKLY TIMER key is shaded. Then press the WEEKLY TIMER key to return the display to normal. This turns the weekly time...
Page 105 - Storing a New Combination of Copy Modes
USING THE SPECIAL FUNCTIONS 101 4. MODE MEMORY You can store and recall a combination of frequently used copy modes at any time you like.In addition to reproduction ratios, you can also store image density levels and copy quantities,colour adjustment modes, editing modes and duplex copying modes. Yo...
Page 106 - Recalling a Stored Combination of Copy Modes
102 Press the MEMORY1 (or, MEMORY2 , ME MORY3 , MEMORY4 ) key. ● The combination of copy modes is stored inmode memory 1 (or, 2, 3, 4) ● Stored combinations of copy modes remainuntil new ones are entered. They are noterased even when the power switch is turnedOFF. Recalling a Stored Combination of C...
Page 107 - COPYING USING PAPER OF UNIVERSAL SIZES; Making US Standard Size Copies
USING THE SPECIAL FUNCTIONS 103 65~300mm (2.6"~11.8") 150~434mm (5.9"~17.0") Original 5. COPYING USING PAPER OF UNIVERSAL SIZES If you set the paper of non-European sizes suchas US standard sizes (Ledger~Statement) in thec a s s e t t e f o r “ U N I V E R S A L ” s i z e , t h e c o...
Page 109 - Making Copies of Non-Standard Originals
USING THE SPECIAL FUNCTIONS 105 After you have set the originals, select the copy quantity, etc. if necessary, and press the START key. Tip: FOLIO is the default size of the UNIVERSALsize. 9 Press the PROGRAM key to enter the Programme menu. 1 Press the UNIVERSAL key. 2 Press the NON STANDARD key. 3...
Page 113 - DEPARTMENT MANAGEMENT
USING THE SPECIAL FUNCTIONS 109 Press the PROGRAM key to enter the Programme menu, and press the Next key then the DEPT.MANAGEMENT key. Enter the password of the administrator (key operator). 1 2 This function allows you to administer the copy quantity of each department by setting an accesscode for...
Page 114 - ID Counter
110 This function displays the number of copies output for each department (or access code) classifiedaccording to colousr mode. ID Counter P r e s s t h e I D C O U N T E R k e y i n t h e Department Management menu. If you want to check the counters of all access codes, press the ALL key. ● The to...
Page 116 - Clearing Counters
112 This function clears a certain department (access code) or all departments to “0”. Clearing Counters Press the CLEAR COUNTER key in the Department Management menu. If you want to clear the counters of all the access codes, press the ALL key. 2 1 8. DEPARTMENT MANAGEMENT (Cont.) If you want to cl...
Page 118 - Registration/Change/Deletion of Access Codes
114 This function registers, changes and deletes the access codes. Registration/Change/Deletion of Access Codes Press the ID REGISTER/CHANGE key in the Department Management menu. Press the REGISTRATION key. 2 1 8. DEPARTMENT MANAGEMENT (Cont.) Registering a new department Using the digital keys, en...
Page 122 - CHANGE OF LANGUAGE ON THE DISPLAY PANEL
118 Press the PROGRAM key to enter the Programme menu, press the Next key twice to display the panel on the right, then press the CHANGE LANGUAGES key. 10. CHANGE OF LANGUAGE ON THE DISPLAY PANEL Press one of the other languages. You can change the language on the display panel. 1 2
Page 125 - USING THE OPTIONAL STAPLE SORTER
121 USING THE OPTIONAL SORTER 6. USING THE OPTIONAL STAPLE SORTER 1. Description of the Main Components . . . . . . 122 2. Non-sort Copying . . . . . . . . . . . . . . . . . . . . . . 123 3. Sort or Staple Sort Copying . . . . . . . . . . . . . . 124 4. Group Copying . . . . . . . . . . . . . . . . ...
Page 126 - DESCRIPTION OF THE MAIN COMPONENTS
122 STAPLE Stapler* Stapler cover* Sort bins (Bins "1" ~ "20") Non-sort bin Staple cartridge* key* In the non-sort mode, copies exit into this bin. However, they will also go into the sort bins when more than 250 sheets are copied or depend-ing upon the size of paper selected. The la...
Page 128 - SORT OR STAPLE SORT COPYING; Sort or Staple Sort
124 3. SORT OR STAPLE SORT COPYING Press the NON-SORT, NON-STAPLE key on the Basic menu to enter the Sorter menu. ● To select the SORT mode, press the SORTkey. Sort or Staple Sort 1 ● To select the SORT/STAPLE mode, press theSTAPLE SORT key. 5 page originals Example: Making 5 sets of copiesfrom 5-pa...
Page 131 - Manual Stapling
127 USING THE OPTIONAL SORTER Manual Stapling 1 Align the edges of the copies and insert them into the first sort bin. ● The copies should be inserted fully inside andmoved to the right and to the front until beingstopped. ● The STAPLE key lamp will come on. ● The maximum number of copies is shownbe...
Page 133 - WHEN THE GRAPHIC SYMBOLS FLASH; Misfeeding in the Automatic
129 WHEN THE GRAPHIC SYMBOLS FLASH 7. WHEN THE GRAPHIC SYMBOLS FLASH 1. Add Paper Symbol . . . . . . . . . . . . . . . . . . . . . 130 2. Replace Toner Bag Symbol . . . . . . . . . . 134 3. Add Toner Symbol . . . . . . . . . . . . . . . . . 136 4. Clear Paper Symbol . . . . . . . . . . . . . . . . 1...
Page 134 - Adding Paper to the Front Cassette
130 Limit line Side guide Side guide 0.5mm 0.5mm When the paper supply in the selected cassette or the optional large-capacity feeder runsout, the cassette or large-capacity feeder symbol on the display panel flashes and thismessage appears: Add paper Add paper as described below. 1 2 Adding Paper t...
Page 137 - Changing the Paper Size of the Cassette
133 WHEN THE GRAPHIC SYMBOLS FLASH Size mark plate Paper size indicator 1 The paper size of the cassette can be changed to any of A3, B4, A4, A4-R and A5-R. Use thefollowing procedure. 3 12 4 Changing the Paper Size of the Cassette Pull out the cassette slowly and fully. Move the side guides so that...
Page 138 - Replacing Procedure; REPLACE TONER BAG
134 When the toner bag becomes full of used toner, theREPLACE TONER BAG symbol flashes and this message appears: Dispose of used tonerPress INFO Replace the toner bag as described below. Replacing Procedure 1 2 2. REPLACE TONER BAG SYMBOL Open the right-hand front cover. Open the left-hand front cov...
Page 140 - SYMBOL
136 When the toner supply in a toner cartridge runsout, the ADD TONER symbol and the symbol that shows the corresponding toner colour flashand then the following message appears on theBasic menu: Install new Yellow toner cartridgePress INFO Replace the toner cartridge as described below. 3. ADD TONE...
Page 142 - : Misfeeding inside of the Copier
138 4. CLEAR PAPER SYMBOL When a paper misfeed occurs in the copier, theCLEAR PAPER symbol flashes and the following message will appear: Misfeed in copierPress INFO The CLEAR PAPER symbol flashes in different positions in the diagram depending on where thepaper has misfed. Remove the misfed paper a...
Page 147 - : Misfeeding in the Automatic Duplexer
143 WHEN THE GRAPHIC SYMBOLS FLASH Lower guide ofexit side 2 : Misfeeding in the Automatic Duplexer 1 Remove the copy receiving tray. ● If a staple sorter is attached, first pull it awayfrom the copier by lifting the release lever. 2 Open the exit cover and remove any misfed paper. 4 Close the exit ...
Page 149 - : Misfeeding from the Cassettes
145 WHEN THE GRAPHIC SYMBOLS FLASH Holding its handle, open the feed side cover slowly. 1 3 : Misfeeding from the Cassettes Remove any misfed sheets of paper. 2 Close the feed side cover. 3
Page 150 - : Misfeeding in the Large-Capacity Feeder
146 4. CLEAR PAPER SYMBOL (Cont.) Open the large-capacity feeder. ● Holding its handle as shown, lift it to unlockit and open the feeder slowly away from thecopier. 1 Remove any misfed sheets of paper from the feeder as shown. 23 Close the large-capacity feeder slowly and fully. 4 3 : Misfeeding in ...
Page 151 - : Misfeeding in the Automatic Document Feeder
147 WHEN THE GRAPHIC SYMBOLS FLASH Open the feed-side cover of the automatic document feeder and remove any misfed original. 1 Raise the automatic document feeder and remove any misfed original. ● If an original is left on the glass. remove it. 2 3 Close the feed-side cover. 4 4 : Misfeeding in the ...
Page 152 - : Misfeeding in the Bypass Guide
148 4. CLEAR PAPER SYMBOL (Cont.) 5 : Misfeeding in the Bypass Guide Open the exit cover of the automatic document feeder and remove any foreign matter such as bits of paper, paper clips, etc. 5 67 Raise the automatic document feeder and remove any misfed paper. Close the automatic document feeder. ...
Page 153 - : Misfeeding in the Staple Sorter
149 WHEN THE GRAPHIC SYMBOLS FLASH 1 Remove any misfed paper in the staple sorter bins. Lift the release lever and move the staple sorter slowly away from the copier. 2 3 Pull open the paper transport guide of the staple sorter and remove the misfed paper. 6 : Misfeeding in the Staple Sorter 4 Close...
Page 154 - Replacing Staples
150 1 2 Remove the empty staple cartridge ● Lift the cartridge slightly and slide it out. 5. REPLACING STAPLES Open the stapler cover. The STAPLE symbol flashes on the staple sorter when the following occur: ● The stapler of the staple sorter has run out ofstaples and this message appears: Set stapl...
Page 156 - REMOVING JAMMED STAPLES; Removing Jammed Staples
152 1 2 Holding the stapler unit as shown, lift its outer side slightly (arrow 1 ) and take it out slowly toward you (arrow 2 ). 6. REMOVING JAMMED STAPLES Turn OFF the power switch of the copier and open the stapler cover and loosen the wing nut that holds the stapler unit in place. Wing nut 1 2 3 ...
Page 161 - SIMPLE TROUBLESHOOTING
157 MAINTENANCE 2. SIMPLE TROUBLESHOOTING Status Items to be Checked Countermeasure Reference page Copierdoes notstart Displaypaneldoes notchangewhenkeys oricons arepressed Is the power cord plug firmly insertedin the outlet? Are the front covers firmly closed? Are the bypass feed unit cover andthe ...
Page 165 - SPECIFICATIONS OF OPTIONS
161 SPECIFICATIONS, ACCESSORIES & OPTIONS Automatic Duplexer Type Acceptable Original Size Maximum Capacity Dimensions Weight Power Source Power Consumption MD-5007 Modular (cassette-type) Minimum : A5-R Maximum : A3 Paper weight : Plain paper (64~90g/m 2 ) mode only 50 sheets (A4, 64~80g/m 2 )....
Page 168 - COPYING FUNCTION COMBINATION MATRIX
164 4. COPYING FUNCTION COMBINATION MATRIX Function set first Basic settings Modes Duplex Sorting Editing functions APS AMS Enlarge/Reduce Oroginal mode selection Automatic colour selection 1 → 1 1 → 2 2 → 1 2 → 2 Book → 2 Non–sort Sort Group Staple Sort Edge erase Image shift Dual page 2 IN 1 2 IN ...
Page 169 - IMAGE QUALITY ADJUSTMENT COMBINATION MATRIX
165 SPECIFICATIONS, ACCESSORIES & OPTIONS 5. IMAGE QUALITY ADJUSTMENT COMBINATION MATRIX Function set last Function set first Cop y density Man ual A uto Hue Satur ation Colour balance RGB Shar pness Bac k g round Vivid Clear Wa rm Cool Colour mode selection Cop y density Colour mode selection O...
Page 171 - FOR COPYING FUNCTIONS
DIGITAL COLOUR PLAIN PAPER COPIER OPERATOR'S MANUALFOR COPYING FUNCTIONS DIGITAL COLOUR PLAIN PAPER COPIER OPERATOR'S MANUAL FOR COPYING FUNCTIONS 1-1,KANDA NISHIKI-CHO,CHIYODAKU,TOKYO,101-8442,JAPAN Recycled paper is used for the inside pages of this book. This Operator’s Manual is printed with ink...
