Page 2 - For AU EMC; FCC Notice; Redirect or relocate the receiving antenna.; CAUTION; © Link Evolution Corp. All Rights Reserved.
Copyright © 2003by TOSHIBA TEC CORPORATIONAll Rights Reserved570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN ■ For AU EMC FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device,in accordance to Part 15 of the FCC Rules. These limits are desig...
Page 3 - General
(i) Safety Summary ENGLISH VERSION EO1-33014 The B-415-GH25-QM is equipped with a wireless communication device, TEC-BTM. Please be sure toread the enclosed Precautions for Handling of Wireless Communication Devices before using this product. Precautions for Handling of Wireless Communication Device...
Page 5 - Safety Summary; WARNING; Do not load the battery with the electrodes reversed.
(iii) Safety Summary ENGLISH VERSION EO1-33014 Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautionsnecessary for safe handling are included in this manual. All warnings and cautions contained in thismanual and written inside or outside...
Page 6 - Do not drop or shock the machine as this may cause machine failure.; Precautions; Temperatures below -5°C and above 50°C
(iv) Safety Summary ENGLISH VERSION EO1-33014 CAUTION • Keep away from flame or other sources of heat. Failure to do this may cause fire or machine failure. • Do not drop or shock the machine as this may cause machine failure. • During lightening, turn off and keep away from the machine because of d...
Page 7 - TABLE OF CONTENTS; Page
CAUTION: 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC. 2. The contents of this manual may be changed without notification. 3. Please refer to your local Authorized Service representative with regard to any queries you may have in this manual. E...
Page 8 - Linerless Adapter
E1-1 1. INTRODUCTION ENGLISH VERSION EO1-33014 1. INTRODUCTION Thank you for purchasing the TEC B-415 series portable printer.The B-415 printer displays its high performance with extraordinarily high speed printing up to 50.8 mm/sec. It has a considerably compact and light body of 111 mm in height, ...
Page 11 - External DC Input
E2-3 2. SPECIFICATIONS ENGLISH VERSION EO1-33014 2.6 External DC Input 2.7 Battery 2.6 External DC Input Item Description Conditions Input voltage: DC9V ± 5% Input current: Max. 8A Connector specification Printer side: TCP7361-11-0201 Adapter side: TCS7361-01 Connector pin arrangement Pin1: DC9V, Pi...
Page 12 - Label; Inner diameter of paper core
E2-4 2. SPECIFICATIONS ENGLISH VERSION EO1-33014 2.9 Media 2.9 Media Label Receipt/Linerless Media type Label Receipt Linerless Item Batch Strip Without black mark With black mark With black mark A: Label/Receipt Pitch 10 ~ 400 13 ~ 71.5 --- 10 ~ 400 10 ~ 400 B: Label/Receipt length 7 ~ 390 10 ~ 63....
Page 13 - Description of LED Lamp
E3-1 3. APPEARANCE ENGLISH VERSION EO1-33014 3. APPEARANCE 3.1 Front/Rear View Front View Rear View 3.1 Front/Rear View TOSHIBA TEC CORPORA TION Shoulder Strap Holder AC AdapterTerminal(Inlet) Power Switch Media Cover Media CoverRelease Catch Status Indicator 0 0 0 PRINT BATTERY ERROR Battery Cover ...
Page 14 - LOADING AND REMOVING THE BATTERY; LITHIUM ION BATTERY; Battery Performance; Slide the battery cover to open.
E4-1 4. LOADING AND REMOVING THE BATTERY ENGLISH VERSION EO1-33014 4. LOADING AND REMOVING THE BATTERY 4. LOADING AND REMOVING THE BATTERY CAUTION:1. Be sure to turn off the printer before loading the battery.2. Use the specified battery only. Failure to do this may cause fire or electric shock.3. I...
Page 15 - TO CHARGE THE BATTERY PACK; CHARGE
E4-2 4. LOADING AND REMOVING THE BATTERY ENGLISH VERSION EO1-33014 4. LOADING AND REMOVING THE BATTERY • TO CHARGE THE BATTERY PACK This printer includes no battery charger. Charging the battery requires an exclusive batterycharger. Please order the following one to your authorized TOSHIBA TEC repre...
Page 16 - Using the battery pack at once; ATTACHING THE SHOULDER STRAP; ATTACHING THE SHOULDER STRAP
E4-3 4. LOADING AND REMOVING THE BATTERY ENGLISH VERSION EO1-33014 The charging time may differ depending on the condition of the battery pack or the temperature ofthe environment. • Using the battery pack at once Remove the battery pack when required. It can be used even if the charging is not comp...
Page 17 - Requirements for Operation; Interface Cables
E6-1 6. SET UP PROCEDURE ENGLISH VERSION EO1-33014 6.1 Requirements for Operation 6. SET UP PROCEDURE 6.1 Requirements for Operation This machine has the following requirements: • The host computer must have a serial port. • To communicate with host, either an exclusive RS-232C cable is required. RS...
Page 18 - How to Load the Liner Backed Label Roll; Place the printer on a level surface as shown below.
E7-1 7. LOADING THE LABEL ENGLISH VERSION EO1-33014 7. LOADING THE LABEL 7.1 How to Load the Liner Backed Label Roll 1 1 2 3 Media Cover Media CoverRelease Catch Media Cover Release Catch Strip Cover Fig. 7-1 4. Fully raise up the release lever, and then slide the paper guide (R) to the right. Fig. ...
Page 19 - to section 7.2 How to load the linerless label roll.; Strip Issue
E7-2 7. LOADING THE LABEL ENGLISH VERSION EO1-33014 5. Load the liner backed label roll as Fig.7-3 shows. 6. Slide the paper guide (R) to accommodate the label roll width, and then push the release leverdownward to fix the paper guide (R). NOTE: Before fixing the paper guide (R), make sure that the ...
Page 20 - Open the media cover.; Open the media cover.
E7-3 7. LOADING THE LABEL ENGLISH VERSION EO1-33014 7.2 How to Load the Linerless Label Roll 8. Push down the media cover until the two cover release catches click back into the lock position. NOTE: If the media cover is open and unlocked, an error will result and the printing will not beperformed. ...
Page 21 - Attach the linerless adapters to the paper guides.
E7-4 7. LOADING THE LABEL ENGLISH VERSION EO1-33014 7.2 How to Load the Linerless Label Roll 3. Attach the linerless adapters to the paper guides. Fig. 7-8 Paper Guide Linerless Adapter Paper Guide 4. Loading the linerless label roll is basically the same as described in the liner backed label roll....
Page 22 - communication or IrDA.; Printer
ENGLISH VERSION EO1-33014 CAUTIONS:1. Radio communication between a handy terminal and the B-415 printer is guaranteed when the handy terminal is in the operator’s hand and the printer is secured at the waist. Proper radiocommunication may not be obtained when used in other conditions and in areas s...
Page 23 - For GH25 model
ENGLISH VERSION EO1-33014 4. Tear off the printed media upward or downward with the cutter.NOTE: Do not pull the media out of the printer, as this will misalign the print position of the next label. Media 9. SELF-DIAGNOSTIC TEST PRINT Fig. 8-2 9. SELF-DIAGNOSTIC TEST PRINT 1. Turn the power on while...
Page 24 - Regarding the print contents refer to the specifications.
ENGLISH VERSION EO1-33014 2. Pressing the [FEED] button again issues the second label of the test print. Pressing the [FEED]button once more, issues the second label of the test print again. 3. Regarding the print contents refer to the specifications. E9-2 9. SELF-DIAGNOSTIC TEST PRINT 9. SELF-DIAGN...
Page 25 - side causing erratic media advance and poor print quality.
E10-1 10. CARE/HANDLING OF THE MEDIA ENGLISH VERSION EO1-33014 10. CARE/HANDLING OF THE MEDIA 10. CARE/HANDLING OF THE MEDIA CAUTION:Be sure to read carefully and understand the Supply Manual. Use only media which meets thespecified requirements. Use of non-specified media may shorten the head life ...
Page 26 - GENERAL MAINTENANCE
E11-1 11. GENERAL MAINTENANCE ENGLISH VERSION EO1-33014 Fig. 11-2 11.1 Cleaning 11.1 Cleaning To help retain the high quality and performance of your printer it should be regularly cleaned. Thegreater the usage of the printer, the more frequent the cleaning. (i.e. low usage = weekly: high usage= dai...
Page 27 - discolor, loose their shape or develop structural weakness.; Removing Jammed Media; Turn off the printer.
E11-2 11. GENERAL MAINTENANCE ENGLISH VERSION EO1-33014 11.2 Covers and Operation Panel The covers should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a milddetergent solution. NOTE: Clean the printer cover with an electrostatic free cleaner for automated office equipment....
Page 28 - LED DISPLAY AND TROUBLESHOOTING; When the power is turned on.; Thermal Head Disconnection Error; LED flashing repeats ON and OFF at the interval of 0.1 sec.; Please contact your authorized TOSHIBA TEC representative.
E12-1 12. LED DISPLAY AND TROUBLESHOOTING ENGLISH VERSION EO1-33014 Close the cover Close the cover after installing a label. Close the cover after installing a label. Close the cover (See NOTE) Stop issuing labels for a while. (See NOTE) (See NOTE) Replace the battery, or charge the battery. Close ...
