Toshiba A60 - Manual

5 5.375 x 8.375 ver 2.3 Telephone Company Procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures. If these changes might affect your servi...

6 5.375 x 8.375 ver 2.3 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or ...

7 5.375 x 8.375 ver 2.3 NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to t...

8 5.375 x 8.375 ver 2.3 Wireless LAN and your Health Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example...

9 5.375 x 8.375 ver 2.3 Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. L’utilisation de ce dispositif est autorisée seulement...

11 5.375 x 8.375 ver 2.3 USA – Federal Communications Commission (FCC) This device complies with Part 15 of FCC Rules. Operation of the devices in a Wireless LAN System is subject to the following two conditions: ❖ This device may not cause harmful interference. ❖ This device must accept any interfe...

12 5.375 x 8.375 ver 2.3 Caution: Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harm...

13 5.375 x 8.375 ver 2.3 2. Indication The indication shown below appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. OF: This equipment uses OFDM modulation. 3 The interference range of this equipment is less than 40m. 4 This equ...

14 5.375 x 8.375 ver 2.3 Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wireless module into other device. ❖ 5.17 GHz to 5.23 GHz for indoor use ...

19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Bluetooth wireles...

20 5.375 x 8.375 ver 2.3 Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth™ products with all PCs and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth™ cards from TOSH...

21 5.375 x 8.375 ver 2.3 community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the buil...

22 5.375 x 8.375 ver 2.3 Caution: FCC Interference Statement This device complies with part15 of the FCC rules. Operation is subject to the following two conditions: ❖ This device may not cause harmful interference, and ❖ This device must accept any interference received, including interference that...

23 5.375 x 8.375 ver 2.3 The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations. Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial,...

25 5.375 x 8.375 ver 2.3 Location of the required label (Sample shown below. Location of the label and manufacturing information may vary.) This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the user’s guide carefully and keep it f...

27 5.375 x 8.375 ver 2.3 Computer disposal information This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.o...

28 5.375 x 8.375 ver 3.1 Contents Introduction .............................................................. 35 This guide .............................................................. 36Safety icons ........................................................... 36 Other icons used .....................

30 Contents 5.375 x 8.375 ver 3.1 Windows ® special keys .................................... 82 Overlay keys..................................................... 83 Starting a program ................................................. 84 Starting a program from the Start menu .......... 85Starting a...

33 Contents 5.375 x 8.375 ver 3.1 Hotkey utility ........................................................ 157TOSHIBA Console ................................................ 157 Customize Your Computer ............................. 159Security............................................................

35 5.375 x 8.375 ver 2.3 Introduction Welcome to the world of powerful and portable multimedia computers! With your new Toshiba notebook computer, your access to information can accompany you wherever you go. Your system comes the Microsoft ® Windows ® XP Home or XP Pro operating system. Your operat...

36 Introduction This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about thefeatures and specification...

37 Introduction Safety icons 5.375 x 8.375 ver 2.3 the seriousness of the risk, and the icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not ...

38 Introduction Other documentation 5.375 x 8.375 ver 2.3 HINT: This icon denotes helpful hints and tips. DEFINITION: This icon indicates the definition of a term used in the text. Other documentation Your computer comes with the following documentation: ❖ This electronic user’s guide. ❖ Guides for ...

39 5.375 x 8.375 ver 2.3 Chapter 1 Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is designed to be used in a variety of locations ...

40 Getting Started Selecting a place to work 5.375 x 8.375 ver 2.3 ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in temperature or humidity and sources of temperature chang...

41 Getting Started Selecting a place to work 5.375 x 8.375 ver 2.3 Placement of the computer Proper placement of the computer and external devices is important to avoid stress-related injuries. ❖ Place the computer on a flat surface at a comfortable height and distance. You should be able to type wi...

42 Getting Started Selecting a place to work 5.375 x 8.375 ver 2.3 Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort. ❖ Position your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfor...

43 Getting Started Selecting a place to work 5.375 x 8.375 ver 2.3 Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes. Arms and wrists ❖ Avoid bending, arching, or t...

44 Getting Started Selecting a place to work 5.375 x 8.375 ver 2.3 Other precautions Your notebook computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel. You should observe certain precautions to further reduce the risk of personal injury or damage to ...

45 Getting Started Selecting a place to work 5.375 x 8.375 ver 2.3 Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both. ❖ Keep the computer and disks away from objects that generate strong magnetic fields, such as large stereo speakers. Info...

46 Getting Started Setting up your computer 5.375 x 8.375 ver 2.3 Setting up your computer TECHNICAL NOTE: You must complete all set up steps up to “Setting up your software” before adding external or internal components to your computer. These components include, but are not limited to, a mouse, ke...

47 Getting Started Setting up your computer 5.375 x 8.375 ver 2.3 To register online, your computer must be connected to the Internet via a voice-grade telephone line or a Local-Area-Network (LAN). If you chose not to register now, you may register with Toshiba by clicking the Register with Toshiba ...

48 Getting Started Connecting to a power source 5.375 x 8.375 ver 2.3 ❖ Connect a mouse (see “Connecting a mouse” on page 68 ) ❖ Connect a local printer (see “Connecting a printer” on page 69 ) ❖ Install PC Cards (see “Using PC Cards” on page 148 ) ❖ Connect an external keyboard (see “Using an exter...

51 Getting Started Charging the main battery 5.375 x 8.375 ver 2.3 Charging the main battery Before you can use the battery to power the computer, you must charge it. Connect the computer to a live power outlet using the AC adapter and power cable. The AC power light glows green and the battery ligh...

52 Getting Started Using the computer for the first time 5.375 x 8.375 ver 2.3 Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel 1 Slide the display latch to the right. 2 Lift the display panel. Sample opening the disp...

53 Getting Started Using the computer for the first time 5.375 x 8.375 ver 2.3 Over a period of time, and depending on the usage of the computer, the brightness of the LCD Screen will deteriorate. This is an intrinsic characteristic of LCD technology. Screen will dim when the computer is operated on...

54 Getting Started Using the computer for the first time 5.375 x 8.375 ver 2.3 Sample pressing the power button When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely. The preinstalled operating system loads automatically. T...

55 Getting Started Using the TouchPad™ 5.375 x 8.375 ver 2.3 The TOSHIBA Console window appears. For more information see “TOSHIBA Console” on page 157 . 2 Click Security . 3 Click User password . 4 Follow the on-screen instructions. The password requirement becomes active the next time you turn on ...

56 Getting Started Using the TouchPad™ 5.375 x 8.375 ver 2.3 ❖ To move the cursor to the right side of the page, slide your finger across the TouchPad from left to right. ❖ To move it to the left side, slide your finger from right to left. Because the TouchPad is much smaller than the display screen...

58 Getting Started Using the TouchPad™ 5.375 x 8.375 ver 2.3 Using TOSHIBA Touch and Launch TOSHIBA Touch and Launch is a program that adds features to the TouchPad. For example, by selecting an icon you can: ❖ Open a document ❖ Launch a program ❖ Show a list of windows and switch the active window ...

60 Getting Started Using the TouchPad™ 5.375 x 8.375 ver 2.3 TOSHIBA Touch and Launch is controlled/adjusted via an icon on the system tray. The icon changes color when the TOSHIBA Touch and Launch is active. Double-click the icon to open the TOSHIBA Touch and Launch Settings window. Right-click the...

61 Getting Started Using the TouchPad™ 5.375 x 8.375 ver 2.3 In the Corner Assignment section you can change the icons you see at the four corners of the TOSHIBA Touch and Launch window using the drop-down list boxes. The icons are referred to as tables in the TOSHIBA Touch and Launch Settings dialo...

66 Getting Started Installing additional memory (optional) 5.375 x 8.375 ver 2.3 Removing a memory module If you use the computer for a long time, the memory module will become hot. If this happens, let the module cool to room temperature before you replace it. Do not try to remove a memory module w...

68 Getting Started Using an external keyboard 5.375 x 8.375 ver 2.3 Checking total memory When you add or remove memory, you can check that the computer has recognized the change. To do this: 1 Click Start , Control Panel 2 Click Performance and Maintenance . 3 Click System . 4 The General tab view ...

69 Getting Started Connecting a printer 5.375 x 8.375 ver 2.3 Connecting a printer You can connect a USB-compatible printer to your computer through the USB ports. You can connect a USB printer after you turn on the computer. Alternatively, you can connect a parallel printer to the computer’s parall...

70 Getting Started Connecting a printer 5.375 x 8.375 ver 2.3 If your printer has not been detected automatically when connected to the computer, you must install the printer driver for the model of printer that is connected to your computer. You install the printer driver either by following the in...

72 Getting Started Connecting an optional external diskette drive 5.375 x 8.375 ver 2.3 5 Follow the on-screen instructions. HINT: If you are using more than one printer, make sure the name is descriptive enough to help you tell the difference. Connecting an optional external diskette drive You can ...

73 Getting Started Using external display devices 5.375 x 8.375 ver 2.3 Using external display devices Your computer comes with a built-in LCD display, but you can easily attach an external monitor to your computer if you need a larger screen. Once you have connected an external display device, you ...

74 Getting Started Using external display devices 5.375 x 8.375 ver 2.3 ❖ External device only ❖ Built-in display and TV (or other external video device) simultaneously ❖ TV (or other external video device) only 3 Release the Fn key for the selection to take effect. TECHNICAL NOTE: You can also chan...

75 Getting Started Powering off the computer 5.375 x 8.375 ver 2.3 enabled and the Display area (resolution) set to 640 x 480 or 800 x 600, the image on the internal display panel may appear stretched. The Windows ® XP operating system by default does not display resolutions below 800 x 600. To disp...

76 Getting Started Caring for your computer 5.375 x 8.375 ver 2.3 ❖ To leave the computer off for a longer period, you can use the Windows ® Turn Off command when not connected to a domain server or the Shut down command when connected to a domain server instead. Never turn off the computer while an...

77 Getting Started Caring for your computer 5.375 x 8.375 ver 2.3 Moving the computer Before moving your computer, even across the room, make sure all disk activity has ended (the disk activity lights stop glowing) and all external peripheral cables are disconnected. Never pick up the computer by it...

79 5.375 x 8.375 ver 2.3 Chapter 2 Learning the Basics This chapter lists some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work temporarily stays in the computer’s memory until you save it to the disk. You will lose all uns...

81 Learning the Basics Using the keyboard 5.375 x 8.375 ver 2.3 Using the keyboard Sample keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The spacebar creates a space character instead of just passing over an area of the page. ❖ The low...

82 Learning the Basics Using the keyboard 5.375 x 8.375 ver 2.3 Ctrl, Fn, and Alt keys Sample Ctrl, Fn and Alt keys The Ctrl , Fn , and Alt keys do different things depending on the program you are using. For more information, see your program documentation. Function keys The function keys (not to b...

83 Learning the Basics Using the keyboard 5.375 x 8.375 ver 2.3 Overlay keys Sample keyboard overlay keys The keys with numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the ten-key keypad o...

84 Learning the Basics Starting a program 5.375 x 8.375 ver 2.3 To use the cursor control overlay when the numeric overlay is on, press and hold down Shift while you use the cursor control keys. To return to the numeric overlay, release Shift . To turn off the numeric keypad overlay, hold down the F...

85 Learning the Basics Starting a program 5.375 x 8.375 ver 2.3 ❖ Use Windows Explorer to locate the program file ❖ Use the Run dialog box Starting a program from the Start menu When you install a program, the operating system usually puts an icon in the All Programs menu. To start a program that ha...

86 Learning the Basics Starting a program 5.375 x 8.375 ver 2.3 2 Click Accessories . 3 Click Windows Explorer . 4 Click My Computer to expand the window. 5 In the left part of the window, under the C: icon, double-click the folder containing the program, in this case Program Files . Windows ® Explo...

88 Learning the Basics Saving your work 5.375 x 8.375 ver 2.3 Saving your work Before you turn off the computer, save your work to the hard disk drive. Always save your data even when you are using the Stand by. If your battery fully discharges, your information will be lost. Your computer can be co...

89 Learning the Basics Saving your work 5.375 x 8.375 ver 2.3 3 Type a file name, then click Save . HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name. The Windows ® XP operating system supports file names o...

90 Learning the Basics Printing your work 5.375 x 8.375 ver 2.3 To save: ❖ A file you are updating, open the program’s File menu and click Save . ❖ A new file, choose Save As from the File menu, type a name for the file, and click OK . HINT: To make another copy of the file you are currently working...

91 Learning the Basics Backing up your files 5.375 x 8.375 ver 2.3 Backing up your files Backing up your files means copying individual files to media, such as a CD. Or copying entire sections of your hard disk to another device such as a tape drive or to your network partition. To back up to a CD, ...

92 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to overwrite a file that already exists on the hard disk. Make sure the backup version is the one you want before overwriting the exi...

93 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 DVD-ROM or multi-function drive components Your DVD-ROM or multi-function drive may look like this: Sample DVD-ROM or multi-function drive Never press the eject button or turn off the computer while the drive-in-u...

94 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 The previous track button returns to the preceding track on the disc. The next track button skips to the following track on the disc. The play/pause button starts playing the disc or makes it pause if currently pl...

96 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 Sample positioning the disc on the spindle Make sure the disc is properly positioned on the spindle. If you position the disc incorrectly, it can jam the disc tray. 6 Close the disc tray by pressing gently on the ...

98 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 Sample Windows Media ® Player window The Windows Media ® Player control panel works much like an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button on the CD Player control pan...

99 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 1 Open the Start menu and select My Computer. 2 Click the DVD-ROM/multi-function drive icon. The disk drive will run the CD. If your disk does not run using this method, try using an application that is associated...

100 Learning the Basics Using the DVD-ROM or multi-function drive 5.375 x 8.375 ver 2.3 Removing a disc with the computer on Never press the eject button or turn off the computer while the drive-in-use light is glowing. Doing so could damage the disk or the drive. 1 Locate and press the eject button...

101 Learning the Basics Powering down the computer 5.375 x 8.375 ver 2.3 Caring for CD and DVD discs ❖ Store your discs in their original containers to protect them from scratches and keep them clean. ❖ Never bend a disc or place heavy objects on top of it. ❖ Hold a disc by its outside edge. Fingerp...

102 Learning the Basics Powering down the computer 5.375 x 8.375 ver 2.3 Each option has its advantages. TECHNICAL NOTES: Before using any of these options to power down your computer, save your files and make sure the disk activity lights are off. If you change your mind and decide to continue work...

103 Learning the Basics Powering down the computer 5.375 x 8.375 ver 2.3 Restart command Restart is the same as Turn Off or Shut down but automatically powers up the computer. Use it when you need to reload the operating system, for example to activate changes to system settings. Hibernation command...

104 Learning the Basics Powering down the computer 5.375 x 8.375 ver 2.3 Standby command Standby puts the computer into a power-saving mode. Standby holds the current state of the computer in memory so that, when you restart the computer, you can continue working from where you left off. Factors whe...

105 Learning the Basics Using Turn Off or Shut down 5.375 x 8.375 ver 2.3 Using Turn Off or Shut down If you are using the Windows ® XP Home operating system, or are using the Windows ® XP Professional operating system and are not a member of a domain, power off the computer as follows: 1 Click Star...

106 Learning the Basics Using Turn Off or Shut down 5.375 x 8.375 ver 2.3 Sample Shut down computer window 2 Select Shut down from the drop-down list. 3 Click OK . The computer turns itself off. Holding the Shift key while the Turn Off computer Windows ® dialog box is open, changes the Standby butto...

108 Learning the Basics Using Hibernation 5.375 x 8.375 ver 2.3 Starting again after Turn Off or Shut down To start the computer up again, press and release the power button. The on/off light turns on. Using Hibernation When Hibernation is enabled, you can put the computer into Hibernation in more t...

110 Learning the Basics Using Hibernation 5.375 x 8.375 ver 2.3 The computer saves the state of the system, including all open programs and files, to the hard disk. Then the computer turns itself off. Going into Hibernation mode more quickly You can also put the computer into Hibernation mode in the...

112 Learning the Basics Using Standby 5.375 x 8.375 ver 2.3 Starting again from Hibernation mode To start the computer from Hibernation mode, press and release the power button. The computer returns to the screen you were using. If you put the computer in Hibernation mode by closing the display pane...

113 Learning the Basics Using Standby 5.375 x 8.375 ver 2.3 mode. The on/off light ( ) blinks amber indicating the machine is in Standby mode. If you are using the Windows ® XP Professional operating system and are a member of a domain, power off the computer using the Standby command as follows: 1 ...

115 Learning the Basics Toshiba’s online resources 5.375 x 8.375 ver 2.3 Set this option to Standby to put the computer into Standby mode when you close the display panel. 5 Click Apply . 6 Click OK . For more information about the Power Saver utility, see “Power Management” on page 159 . Starting a...

116 5.375 x 8.375 ver 2.3 Chapter 3 Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power standby mode when it is not being used, thereby conserving energy and saving money in the process. It has a numb...

117 Mobile Computing Running the computer on battery power 5.375 x 8.375 ver 2.3 Battery Notice Battery life may vary depending on applications, power management settings. and features utilized. Recharge time varies depending on usage. The battery does not charge while the computer is using all of i...

118 Mobile Computing Charging the batteries 5.375 x 8.375 ver 2.3 Changes to these settings may result in system performance or stability issues. Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup cha...

120 Mobile Computing Charging the batteries 5.375 x 8.375 ver 2.3 Leave the power connected, and the battery should begin charging after a few minutes. HINT: Once the battery is fully charged, we recommend that you operate your computer on battery power until the battery discharges completely. Doing...

121 Mobile Computing Monitoring battery power 5.375 x 8.375 ver 2.3 It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working. When Hibernation mode...

123 Mobile Computing Monitoring battery power 5.375 x 8.375 ver 2.3 The Windows ® operating system has additional power management options that can be accessed through an icon in the Control Panel. For more information, see “Power Management” on page 159 . Conserving battery power How long a fully c...

124 Mobile Computing Monitoring battery power 5.375 x 8.375 ver 2.3 What to do when the battery runs low When the battery runs low you can : ❖ Plug the computer into an external power source and recharge the battery. ❖ Put the computer in Hibernate mode and replace the battery with a charged spare. ...

125 Mobile Computing Changing the main battery 5.375 x 8.375 ver 2.3 Changing the main battery When your battery power is running low, you have two options—connect the computer to an AC power source or install a charged battery. When handling a battery, be careful not to drop it or short-circuit its...

127 Mobile Computing Changing the main battery 5.375 x 8.375 ver 2.3 7 While still holding the release latch in the open position, lift the battery pack out of the computer. Sample removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and disca...

128 Mobile Computing Taking care of your battery 5.375 x 8.375 ver 2.3 Taking care of your battery The following sections offer tips on how to take care of your battery and prolong its life. Safety precautions ❖ If the battery pack produces an odor, overheats or changes color or shape while it is be...

129 Mobile Computing Taking care of your battery 5.375 x 8.375 ver 2.3 ❖ Do not expose the battery pack to fire. The battery pack could explode. Maximizing battery life To maximize the life of your battery pack: ❖ At least once a month, disconnect the computer from a power source and operate it on b...

130 Mobile Computing Disposing of used batteries safely 5.375 x 8.375 ver 2.3 ❖ If you are not going to use the computer for more than eight hours, disconnect the AC adapter. ❖ Store spare battery packs in a cool dry place out of direct sunlight. Disposing of used batteries safely The life of a batt...

131 Mobile Computing Traveling tips 5.375 x 8.375 ver 2.3 Traveling tips The environmental precautions listed in “Selecting a place to work” on page 39 , also apply while traveling. ❖ Never leave your computer on a sunny ledge or in a place where it could get wet or covered in dust. ❖ Always travel ...

132 5.375 x 8.375 ver 2.3 Chapter 4 Exploring Your Options In this chapter, you will explore some of the special features of your Satellite ® Series notebook computer. Exploring the desktop The desktop is the launching pad for everything you can do in the Windows ® XP Home or XP Professional operati...

133 Exploring Your Options Exploring the desktop 5.375 x 8.375 ver 2.3 Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, taskbar, system tray, and background pattern. Sample Windows ® XP operating system desktop Icons An icon represe...

135 Exploring Your Options Exploring the desktop 5.375 x 8.375 ver 2.3 Taskbar Each time you open a program, a button associated with that program appears on the taskbar. With some programs, a button appears on the taskbar for each document or window you open. You can use these buttons to quickly sw...

136 Exploring Your Options Setting up for communications 5.375 x 8.375 ver 2.3 Setting up for communications Your computer comes with a built-in modem that can be connected to a standard voice-grade telephone line. The modem allows you to: ❖ Access the Internet. ❖ Communicate with your office’s loca...

138 Exploring Your Options Setting up for communications 5.375 x 8.375 ver 2.3 Connecting the modem to a telephone line Before you can communicate using the modem, you need to connect it to a telephone line. Your computer’s built-in modem port provides an RJ-11 jack, allowing you to connect the mode...

139 Exploring Your Options Setting up for communications 5.375 x 8.375 ver 2.3 Setting up the connection To set up an office connection, consult your network administrator for network settings and additional considerations. To use a dial-up connection, have your network administrator configure your ...

140 Exploring Your Options An overview of using the Internet 5.375 x 8.375 ver 2.3 To use your wireless communication, flip the wireless antenna on/off switch to the On position. Using the Wi-Fi ® Wireless LAN Mini PCI module Your computer may have an integrated Wi-Fi Wireless LAN Mini PCI module. I...

141 Exploring Your Options An overview of using the Internet 5.375 x 8.375 ver 2.3 The World Wide Web The World Wide Web (or “Web”) is a subset of the Internet—a collection of interlinked documents (located on computers connected to the Internet) that work together using a specific Internet protocol...

142 Exploring Your Options An overview of using the Internet 5.375 x 8.375 ver 2.3 Once you have established an ISP account, you can connect to the Internet. 1 Connect your computer’s modem to a telephone line. For more information on connecting a modem, see “Connecting the modem to a telephone line...

143 Exploring Your Options An overview of using the Internet 5.375 x 8.375 ver 2.3 Internet features The Internet offers many types of communication tools to help you perform many tasks. ❖ Internet email To send and receive your own email, you need a mailbox on the Web or an email address. If you ha...

144 Exploring Your Options Exploring video features 5.375 x 8.375 ver 2.3 Exploring video features Your computer’s video features enable you to view Windows ® presentations or DVD movies on the computer screen (display panel or external monitor). For information on connecting an external monitor, se...

145 Exploring Your Options Exploring audio features 5.375 x 8.375 ver 2.3 4 The Monitor Settings window appears and asks if you want to keep the settings. 5 Click Yes . 6 To change the settings back, repeat steps 2 through 5 . Playing DVDs Your computer must be on for you to use the DVD-ROM or multi...

146 Exploring Your Options Exploring audio features 5.375 x 8.375 ver 2.3 Recording sounds You can make audio recordings and save them as .wav files by connecting an external microphone or other sound source to the microphone jack and using the Sound Recorder feature in the operating system. DEFINIT...

147 Exploring Your Options Exploring audio features 5.375 x 8.375 ver 2.3 3 Click the Record button and speak normally into the microphone. You can only record 60 seconds at a time. 4 When you have finished recording, click the Stop button. 5 To hear what you just recorded, click the Play button. 6 ...

148 Exploring Your Options Using PC Cards 5.375 x 8.375 ver 2.3 TECHNICAL NOTE: Use amplified speakers that require an external power source. Other types of speakers will be inadequate to produce sound from the computer. To play back sound files through external speakers or headphones: 1 Locate the ...

149 Exploring Your Options Using PC Cards 5.375 x 8.375 ver 2.3 To insert a PC Card: 1 Turn off the computer. You may also hot swap a PC Card (see “Hot swapping” on page 150 ). 2 Align the card connectors with the PC Card slot and carefully slide the card into the slot until it locks into place. Sam...

150 Exploring Your Options Using PC Cards 5.375 x 8.375 ver 2.3 Sample removing a PC Card 3 Remove the PC Card and store it properly. Hot swapping One of the great things about PC Cards is that you can replace one PC Card with another while the computer is on. This is called “hot swapping.” Hot swap...

151 5.375 x 8.375 ver 2.3 Chapter 5 Toshiba Utilities Your computer includes several utilities designed to help you to configure your system to best meet your individual needs. Together, these allow you to ascertain certain system details, set additional options, or change default options. These uti...

154 Toshiba Utilities Fn-esse 5.375 x 8.375 ver 2.3 The keys are color-coded as follows: ❖ Available keys are white. ❖ Assigned keys and keys associated with a popup list are shown on the Fn-esse keyboard in the selected color. ❖ Unavailable keys are dark gray. Assigning a key to a program or docume...

156 Toshiba Utilities Fn-esse 5.375 x 8.375 ver 2.3 ❖ To create a popup list with items from various folders, or to pick only a few items from a folder, create a new folder containing only the desired programs and documents. If you are unsure how to do this, refer to your operating system documentat...

157 Toshiba Utilities Hotkey utility 5.375 x 8.375 ver 2.3 Hotkey utility The hotkey utility allows you to receive a confirmation message when you use the hot key combination for Standby [ Fn + F3 ] and Hibernation [ Fn + F4 ]. To activate the utility: Click Start , All Programs , Toshiba , Utilitie...

159 Toshiba Utilities TOSHIBA Console 5.375 x 8.375 ver 2.3 Customize Your Computer The features available in this category are: ❖ Power Management(See “Power Management” on page 159 .) ❖ Mouse (properties) ❖ Hotkey assignment(See “Fn-esse” on page 153 .) ❖ Toshiba Hardware(See “Toshiba Hardware Set...

160 Toshiba Utilities TOSHIBA Console 5.375 x 8.375 ver 2.3 Sample TOSHIBA Power Saver Properties window The TOSHIBA Power Saver Properties window shows the power profiles, which are optimized for several different working environments. You can either use one of the preset modes or create and use yo...

161 Toshiba Utilities TOSHIBA Console 5.375 x 8.375 ver 2.3 ❖ DVD Playback ❖ Presentation ❖ Long Life Although you can change the properties for any of these profiles, this is not recommended. If you need a customized profile, create a new profile with the properties you require. The DVD Playback pr...

163 Toshiba Utilities TOSHIBA Zooming Utility 5.375 x 8.375 ver 2.3 ❖ Keyboard — Allows you to enable or disable the “wake-up on keyboard” feature. The feature allows you to “wake” the machine from Standby by pressing a key. ❖ USB — Allows you to enable or disable USB Legacy Emulation. ❖ LAN — Lets ...

164 Toshiba Utilities Application Launch Button 5.375 x 8.375 ver 2.3 Sample TOSHIBA Zooming Utility Properties screen To zoom in, hold down the Fn key and press 2 ; to zoom out, hold down the Fn key and press 1 . Application Launch Button The Application Launch Button (located to the right of the p...

165 5.375 x 8.375 ver 2.3 Chapter 6 If Something Goes Wrong Some problems you may encounter when using your notebook computer are relatively easy to identify and solve. Others may require help from your dealer or the manufacturer of a software program. This chapter aims to help you solve many proble...

166 If Something Goes Wrong Problems that are easy to fix 5.375 x 8.375 ver 2.3 To close a program that has stopped responding: 1 Press Ctrl , Alt , and Del simultaneously (once). The Windows Task Manager window appears. 2 Click the Applications tab. If a program has stopped responding, the words “n...

167 If Something Goes Wrong Problems when you turn on the computer 5.375 x 8.375 ver 2.3 5 Press Enter to add a paragraph break and type some notes describing what you were doing when you received the message. 6 Save the file and refer to it when you contact the software manufacturer. Problems when ...

168 If Something Goes Wrong The Windows ® operating system is not working 5.375 x 8.375 ver 2.3 diskette drive, press the left or right arrow key and choose your boot-up device. HINT: Press F12 as you power on the computer to access the boot priority menu. The computer displays the WARNING RESUME FA...

169 If Something Goes Wrong The Windows ® operating system is not working 5.375 x 8.375 ver 2.3 ❖ The operating system responds differently from the normal routine. ❖ The screen does not look right. Unless a hardware device has failed, problems usually occur when you change the system in some way su...

170 If Something Goes Wrong The Windows ® operating system is not working 5.375 x 8.375 ver 2.3 ❖ Reboot ❖ Return to OS Choices Menu See your Windows ® documentation for further explanation. TECHNICAL NOTE: If your computer is connected to a network, the Startup menu may display different versions o...

171 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 To access Windows ® XP Help and Support: 1 Click Start , then click Help and Support . The Help and Support Center window appears. 2 Then do one or both of the following: ❖ In the search field, type in the topic of the p...

172 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 The recommended procedure for getting multiple devices to work together is to add and set up one device at a time. After you add each device, test it to make sure it and all previously connected devices work. The device ...

173 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Plug and Play With Plug and Play and the Windows ® XP operating system, avoiding hardware conflicts is easy. Plug and Play is a computer standard that helps the system BIOS (basic input/output system) and the operating s...

174 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Fixing a problem with Device Manager Device Manager provides a way to check and change the configuration of a device. Changing the default settings using Device Manager can cause other conflicts that make one or more dev...

176 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Memory module problems Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. To avoid damaging the memory...

177 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Power and the batteries Your computer receives its power through the AC adapter and power cable or from the system batteries (main battery and real-time clock (RTC) battery). Power problems are interrelated. For example,...

178 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 If the battery light does not glow after 20 minutes, the battery may have reached the end of its useful life. Try replacing it. The battery appears not to power the computer for as long as it usually does. If you frequen...

179 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 You have connected an external keyboard and the operating system displays one or more keyboard error messages. If you have a second keyboard, try it. If it works, the first keyboard may be defective or incompatible with ...

180 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 If you are using an external monitor: ❖ Check that the monitor is turned on. ❖ Check that the monitor’s power cable is firmly plugged into a working power outlet. ❖ Check that the cable connecting the external monitor to...

182 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Disk drive problems Problems with the hard disk or with a diskette drive usually show up as an inability to access the disk or as sector errors. Sometimes a disk problem may cause one or more files to appear to have garb...

184 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 The drive cannot read a diskette. Try another diskette. If you can access the second diskette, the first diskette (not the drive) is probably causing the problem. Run Error-checking on the faulty diskette (for instructio...

185 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Some discs run correctly, but others do not. If the problem is with an application CD-ROM, refer to the software’s documentation and check that the hardware configuration meets the program’s needs. The color of the mater...

186 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Sample Secondary IDE Channel Properties window 7 Click the Advanced Settings tab. 8 Look at Device 0. The current transfer mode should be Ultra DMA Mode 2. If it is not, select Ultra DMA Mode 2 from the pull-down menu an...

187 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 in the Mixer Utility (default Enabled), may cause feedback. Revert to the default settings. PC Card problems PC Cards (PCMCIA-compatible) include many types of devices, such as a removable hard disk, additional memory, o...

188 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 PC Card checklist ❖ Make sure the card is inserted properly into the slot. See “Using PC Cards” on page 148 for how to insert PC Cards. ❖ Make sure all cables are securely connected. ❖ Occasionally a defective PC Card sl...

189 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 The computer stops working (hangs) when you insert a PC Card. Remove the PC Card. If removing the PC Card does not resolve the problem, try restarting the computer. If the computer still does not work, contact the PC Car...

190 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Printer problems This section lists some of the most common printer problems: The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the print...

191 If Something Goes Wrong Resolving a hardware conflict 5.375 x 8.375 ver 2.3 Modem problems This section lists common modem problems: The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port and the ...

192 If Something Goes Wrong Develop good computing habits 5.375 x 8.375 ver 2.3 Develop good computing habits Make sure you are prepared. Save your work frequently. You can never predict when your computer will lock, forcing you to close a program and lose unsaved changes. Many software programs bui...

193 If Something Goes Wrong If you need further assistance 5.375 x 8.375 ver 2.3 Your local computer store or book store sells a variety of self-help books you can use to supplement the information in the guides. If you need further assistance If you have followed the recommendations in this chapter...

194 If Something Goes Wrong If you need further assistance 5.375 x 8.375 ver 2.3 Contacting Toshiba If you still need help and suspect that the problem is hardware-related, Toshiba offers a variety of resources to help you. To stay current on the most recent software and hardware options for your co...

195 If Something Goes Wrong Other Toshiba Internet Web sites 5.375 x 8.375 ver 2.3 Other Toshiba Internet Web sites Toshiba’s worldwide offices toshiba.com Worldwide Toshiba corporate site computers.toshiba.com Marketing and product information in the USA www.toshiba.ca Canada www.toshiba-Europe.com...

197 5.375 x 8.375 ver 2.3 Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls. Volume Mute Instant password security Fn + This hot key b...

198 Hot Keys Instant password security 5.375 x 8.375 ver 2.3 make the display’s content reappear, if no password is set for the current user. With a password The Fn + F1 key combination turns off the display and activates instant security. If you set a blank screen saver, pressing the Fn + F1 key co...

199 Hot Keys Power usage mode 5.375 x 8.375 ver 2.3 To set up a password with a screen saver, go to Windows ® XP Help for instructions: 1 Click Start , Help and Support . 2 In the Search field, type password screen saver. 3 Press Enter . 4 Click the Protect your files with a screen saver password li...

200 Hot Keys Standby mode 5.375 x 8.375 ver 2.3 Standby mode Fn + This hot key puts the computer into Standby mode. ❖ A message box is displayed by default to confirm that the computer is going into Standby mode. This message box can be set so it does not display. Sample Standby confirmation box ❖ F...

201 Hot Keys Hibernation mode 5.375 x 8.375 ver 2.3 Hibernation mode Fn + This hot key puts the computer into Hibernation mode. ❖ If Hibernation mode is enabled (the default) a message box is displayed by default to confirm the computer is going into Hibernation mode. The message box can be set so i...

202 Hot Keys Display modes 5.375 x 8.375 ver 2.3 Display modes Display brightness Fn + This hot key cycles through the power-on display options. The display modes are: ❖ Built-in display panel only ❖ Built-in display panel and external monitor simultaneously ❖ External monitor only In order to use a...

203 Hot Keys Disabling or enabling the TouchPad 5.375 x 8.375 ver 2.3 Disabling or enabling the TouchPad Keyboard hot keys Fn + This hot key turns the cursor control overlay on and off. Fn + This hot key turns the numeric overlay on and off. Fn + This hot key turns the scroll lock feature on and off...

204 5.375 x 8.375 ver 2.3 Appendix B Power Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada UL approvedCSA approved United Kingdom BS...

205 5.375 x 8.375 ver 2.3 Appendix C Using ConfigFree™ with your Toshiba Computer ConfigFree™ is a set of utilities that makes it easy to control communication devices and network connections. ConfigFree also lets you identify communication problems and create profiles for easy switching between loc...

206 Getting Started 5.375 x 8.375 ver 2.3 Getting Started This section contains information about the ConfigFree main screen, and how to start and setup ConfigFree. For more detailed information on setting up and using ConfigFree, see the Help File included in the application. Starting ConfigFree To...

207 ConfigFree Utilities 5.375 x 8.375 ver 2.3 Sample ConfigFree Launcher ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network-connection problems. Using Connectivity Doctor, you can view detailed network information by simply mov...

212 ConfigFree Utilities 5.375 x 8.375 ver 2.3 2 Click your own computer at the center of the map. 3 Configured devices are automatically connected. Devices not yet configured launch the Add New Connection Wizard, where you can configure and connect to the device. Profile Settings The Profile Settin...

214 ConfigFree Utilities 5.375 x 8.375 ver 2.3 Sample Add Profile screen The online help provides real-world examples of setting up profiles for different networking environments. After you set up one or more profiles, you can check their settings and fine-tune them as necessary. Profiles can also b...

217 Using the Automatic Switch 5.375 x 8.375 ver 2.3 Using the Automatic Switch The Automatic Switch feature allows the computer to automatically switch profiles the next time it is powered on. This feature is particularly useful if you want your computer to automatically switch from the network con...

218 Semi-Automatic Switch Feature 5.375 x 8.375 ver 2.3 Semi-Automatic Switch Feature The Semi-Automatic feature alerts you when the computer connects to a Service Set Identifier (SSID) stored in a profile, When the computer connects to the designated SSID, a notification window appears. You can the...

219 5.375 x 8.375 ver 2.3 Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. AC alternating current BIOS basic input/output system bps bits per second CD compact disc CD-ROM compact d...

221 Glossary 5.375 x 8.375 ver 2.3 RAM random access memory RFI radio frequency interference ROM read-only memory RTC real-time clock SCSI small computer system interface SDRAM synchronous dynamic random access memory SRAM static random access memory SVGA super video graphics adapter TFT thin film t...

234 5.375 x 8.375 ver 3.1 Index A AC adapter 48 AC power light 48, 50 accessories memory 62 alarms low battery 124 audio features 145 Auto-Run 98 avoiding injury 40 B battery alarms 124 caring for 128 changing 125 charge not lasting 178 charging 51, 75, 119 disposal 130 installing 125 light 50, 121 ...