Toro WRS1 - Manual
Toro WRS1 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Wireless RainSensor User’s Guide; turn off the receiver.; Component Overview
- Page 3 – Important; : Reconfirm proper operation of the Sensor/Transmitter at the; Quick Start Installation Instructions; Figure 3
- Page 4 – Mounting the Receiver; specific wire connection information.; Detailed Installation Instructions; Figure 6; Red
- Page 5 – Figure 8; Figure 7
- Page 6 – Part 2 - Power Wire Connection
- Page 7 – Installing the Sensor / Transmitter; Testing Signal Strength at the Installation Site; sprinkler spray or runoff from the roof.; Wireless RainSensor with Freeze Sensor
- Page 8 – to ensure proper operation.; Wireless RainSensor Operation; Normal Operation; sensor to ignore the next rain/freeze signal.; Power Down; press the Smart Bypass button once to turn the unit back on.; Receiver Learn Mode; mode if no valid code is received.; Attention Required; indicator is present.; be used in conjunction with any freeze sensor.
- Page 9 – Sensor Adjustment; Rainfall Adjustment; Changing the; The transmission code for the unit is identified by
- Page 10 – Signal Indicator (Installation ValidationTM); Troubleshooting
- Page 11 – RS1000 - Wireless RainSensor; Specifications
- Page 12 – Domestic; sensor are on different branch circuits.; International; Irritrol; Electromagnetic Compatibility
Wireless RainSensor User’s Guide
1
Table of Contents
Component Overview
2
Quick Start Installation Instructions
3
Detailed Installation Instructions
• Mounting the Receiver
• Wiring the Receiver
• Control Wire Connection
• Power Wire Connection
• Initial Receiver Testing
4
4
4
4
6
6
Installing the Sensor / Transmitter
• Testing the Signal Strength
• Installation
• Freeze Sensor Installation
7
7
7
7
Wireless RainSensor Operation
• Normal Operation
• Smart Bypass
• Power Down
• Receiver Learn Mode
• Attention Required
8
8
8
8
8
8
Sensor Adjustment
Battery Replacement
9
9
Changing Sensor/Transmitter Code
9
Troubleshooting
10
Specifications
11
Electromagnetic Compatibility
12
Technical Support Numbers
12
Congratulations on your purchase of the Irritrol Systems Wireless RainSensor. The
Wireless RainSensor components are designed for easy installation, so your sensor
controlled irrigation system will be up and running in minutes.
Before attempting the installation, please read through these instructions in their
entirety, and refer the installation instructions for your irrigation system controller/timer
in regards to connecting a rain sensor or rain switch. The Wireless RainSensor is
designed to work with either Normally Open or Normally Closed sensor circuits.
!
Important
: Please note the following information regarding installation and use of
the Wireless RainSensor components:
• The RainSensor Receiver Module is designed to operate with 24 VAC power
only. Connecting the receiver wiring to 120/240 VAC power may result in severe
equipment damage.
• Installation methods must comply with all applicable national and local building
codes. If you are unsure about proper wiring practices, have a qualified contractor
perform the installation for you.
• The Receiver cover should always be used when the Receiver is installed outdoors.
• The Sensor/Transmitter should never be submerged in water or installed inside a
rain gutter.
Introduction
Wireless RainSensor
TM
Models RS1000 & RFS1000 (+Freeze)
User’s Guide
RS1000
SENSOR STATUS
SIGNAL
POWER
Blinking Bypass ON
Blinking Attn. Reqd.
SENSOR STATUS
PRESS
Receiver
Sensor/Transmitter
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Toro WRS1
Summary
2 Wireless RainSensor User’s Guide Receiver (Figure 1) 1 - Weather-resistant Cover: Slides upward to remove. Protects the receiver module when located outdoors. Keep the cover installed at all times other than when manually operating the receiver. 2 - Sensor Status Indicator: Steady light - Sensor i...
Wireless RainSensor User’s Guide 3 The following instructions are provided for the experienced installer. Refer to Figures 3–5 below. When installing Sensor/Transmitter model RFS1000 for freeze detection, refer to additional freeze sensor installation information on page 8. 1. Disconnect power to th...
4 Wireless RainSensor User’s Guide There are two main components of the Wireless RainSensor: the Receiver and the Sensor/Transmitter. The Receiver is installed adjacent to or within the cabinet of the irrigation system controller. The Sensor/Transmitter is installed outdoors where it is exposed to u...
