Toro RDR0160LVCE - Manual

Toro RDR0160LVCE

Toro RDR0160LVCE – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
Page: / 32

Table of Contents:

  • Page 2 – Installing the Station Wires and Power Wires; Figure 3
  • Page 3 – Installing the Earth Ground; Route the green ground wire from the RDR unit transformer; Important: Make sure the satellite is properly connected to an; Selecting the Decoder Radio Frequency; Important: The base station transmitter, hand-held radio and the; Assigning the Satellite Address Number; Figure 6; Figure 8; Ground Lug
  • Page 4 – Electromagnetic Compatibility; Table 1 - DIP Switch Address Configurations; ON
  • Page 5 – same frequency to enable communication.; Figure 9; Reset
  • Page 6 – to step back through the stations, press; Turns off all stations using the sequential shut down feature.; 1 configures stations 1, 3 and 8 through 11 as switches.; Resets EPROM to factory defaults.
  • Page 8 – © 2003 The Toro Company, Irrigation Division; Align with the lower right corner of the rear plate.
  • Page 9 – Instalación de la unidad RDR; haciéndolo deslizar hacia afuera.; Figura 1; ADVERTENCIA; de bajo voltaje; Número de pieza: RDR0160LVCE
  • Page 10 – los terminales del transformador de la unidad RDR. Vea la Figura 5.; Figura 3; Estación 9; Estación 1
  • Page 11 – Instalación de la conexión a tierra; medio de un cable de cobre desnudo de 10; Selección de la frecuencia de radio del descodificador; Importante: es esencial que el transmisor de la estación base, el; Asignación del número de dirección del satélite; Figura 6; Figura 8
  • Page 12 – Compatibilidad electromagnética; Tabla 1 - Configuraciones de dirección de los interruptores DIP; N ú m e r o d e i n t e r r u p t o r D I P
  • Page 13 – , seguido por el número de dirección del; . Todos los números de; para retroceder a través de las estaciones, oprima; Tabla 2 - Códigos de comando del aparato de radio manual; Código Descripción de la operación; Figura 9; Fusible de 4 A de fusión lenta
  • Page 14 – Código; Inhabilita el arranque de la bomba.; Reposiciona EPROM a los valores preestablecidos en fábrica.
  • Page 16 – Alinear con la esquina inferior derecha de la placa trasera.; © 2003 The Toro Company, División de Riego
  • Page 17 – Installation de l’unité RDR; manière indiquée sur les figures.; Figure 1; AVERTISSEMENT; Guide de l’utilisateur
  • Page 18 – Installation des fils de voies et des fils d’alimentation; Voies 9
  • Page 19 – Mise à la terre; Acheminez le fil de terre vert de la plaquette à bornes du; Sélection de la fréquence radio du décodeur; Important : L’émetteur du poste de base, la radio portative et le; Affectation du numéro d’adresse de satellite
  • Page 20 – Compatibilité électromagnétique; Tableau 1 - Configurations d’adresse des commutateurs DIP; N ° c o m m u t a t e u r D I P
  • Page 21 – Débranchez la source d’alimentation principale du satellite.; Gestion de satellite par radio portative; . Les numéros des voies 1 à 9 doivent; Vérifiez que l’arroseur se met en marche.; trois chiffres d’adresse du satellite et le code de commande 7520; Tableau 2 - Codes de commande par radio portative; Fusible 4 A à action lente
  • Page 22 – Code; Désactive le relais à distance du module de décodeur de fréquence.; Réinitialise l’EPROM aux paramètres par défaut réglés en usine.
  • Page 24 – Alignez sur l’angle inférieur droit de la plaque arrière.
  • Page 25 – Installazione dell’unità RDR; la staffa di montaggio.; AVVERTENZA; Manuale per l’utente
  • Page 26 – Installazione dei cavi delle stazioni e di alimentazione; ), collegare i cavi delle stazioni e il cavo comune delle valvole; fissarli in modo sicuro. Vedere la Figura 5.; Da stazione 9; Comune; Comune delle valvole; Da stazione 1
  • Page 27 – Messa a terra; usando un conduttore di rame nudo da 6 AWG (10 mm; Selezione della frequenza radio di decodifica
  • Page 28 – Compatibilità elettromagnetica; Tabella 1 – Configurazioni indirizzo interruttori DIP; N u m e r o i n t e r r u t t o r e D I P
  • Page 29 – Scollegare la fonte di alimentazione al satellite.; Operazioni satellite con radio portatile; devono essere impostati sulla stessa frequenza.; . I numeri di stazione 1-9 vanno inseriti con lo 0; Controllare che gli irrigatori siano in funzione.; Tabella 2 – Codici di comando per radio portatile; Fusibile ad azione lenta da 4 A
  • Page 30 – Codice; Disabilita l’avviamento della pompa.; Ripristina la EPROM alle impostazioni effettuate alla fabbrica.
Loading the manual

Installation of the RDR (Radio Data Receiver) low-voltage unit will enable you to remotely operate your existing
Vari-Time 4000 satellite controller using a hand-held DTMF radio and/or OSMAC base station. This document covers the
recommended installation procedures and operation of the completed RDR system.

CAUTION: Unless there is a separate agreement between Toro and the original end-user purchaser, Toro

does not warrant the installation, maintenance or service of the system in which the RDR unit is utilized. Toro
assumes no obligation for system design, installation and maintenance. Consult a licensed electrician for
installation and design.
End-user purchaser is responsible for obtaining a radio license for the operation of this equipment.

Installing the RDR Unit

1. Unlock and remove the front access cover of the satellite cabinet.

2. See Figure 13 for the proper dimensions if installing the RDR unit on the back of the satellite cabinet (preferred

method). If installing the RDR unit inside the satellite cabinet on the rear mounting plate, remove the back page of
this document and use Figure 14 as a template for the four screw hole locations.

Note: The RDR unit utilizes a built-in antenna located on the frequency module assembly. If the RDR unit is installed
inside the satellite cabinet or site conditions are such that an alternate antenna is required, an optional antenna
adapter kit (P/N 102-1204) is available.

3. Position the template or mark according to the indicated measurements. Drill holes as indicated on the figures.

4. Locate the removable mounting bracket on the back of the RDR unit. Release the latch and slide the mounting

bracket out.

5. If installing the mounting bracket on the back of the satellite cabinet, use the provided #10-32 machine screws,

washers and nuts as shown in Figure 1. If installing inside the satellite cabinet, secure the mounting bracket on the
rear plate using the provided self-tapping sheet metal screws as shown in Figure 2.

6. Slide the RDR unit onto the mounting bracket until the bracket latch engages the RDR enclosure.

Figure 1

Figure 2

WARNING

ALL WIRING TO THE EXISTING SATELLITE CONTROLLER MUST COMPLY WITH LOCAL AND
NATIONAL ELECTRICAL CODE STANDARDS. TORO IS NOT RESPONSIBLE FOR INJURIES OR
EQUIPMENT DAMAGE DUE TO IMPROPER CONTROLLER INSTALLATION.

DISCONNECT 120/240 V A.C. INPUT POWER WHEN SERVICING THE EXISTING IRRIGATION
SYSTEM. THE IRRIGATION SYSTEM INCLUDES SPRINKLERS, VALVES, SOLENOIDS, PIPING,
WIRING BETWEEN SYSTEM COMPONENTS AND CONTROLLER. FAILURE TO COMPLY CAN
RESULT IN SERIOUS INJURY OR ELECTROCUTION.

OSMAC

®

RDR Low-voltage Retrofit Kit

Part Number RDR0160LVCE

User’s Guide

Español - p. 9 Français - p. 17 Italiano - p. 25

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Installing the Station Wires and Power Wires; Figure 3

Installing the Station Wires and Power Wires 1. Disconnect the primary power source to the existing satellite controller. 2. Unlock the satellite cabinet front cover and the RDR unit door to access the station terminals. 3 For exterior installation, install 1/2" (13mm) flexible water-proof condu...

Page 3 - Installing the Earth Ground; Route the green ground wire from the RDR unit transformer; Important: Make sure the satellite is properly connected to an; Selecting the Decoder Radio Frequency; Important: The base station transmitter, hand-held radio and the; Assigning the Satellite Address Number; Figure 6; Figure 8; Ground Lug

Installing the Earth Ground 1. Route the green ground wire from the RDR unit transformer terminal block to the cabinet rear plate. Secure the ground wirering terminal to the rear plate using the provided self-tappingsheet metal screw. See Figure 6. 2. Remove the lock nut from the lower right corner ...

Page 4 - Electromagnetic Compatibility; Table 1 - DIP Switch Address Configurations; ON

Electromagnetic Compatibility Domestic: This equipment has been tested and found to comply with the limits for a FCC Class A digital device, pursuant to part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in ...

Other Toro Models

All Toro Other