Timex W-92 - Manual

I

I

WED 14

I

I

WED 14

I

I

WED 14

WED

14

IN

MIDDLE

OUT

START WATCH

Important: Set day and date first!

Remove guard from crown and

push in. For screw-in setting crown, turn

COUNTERCLOCKWISE

to

loosen. Note: Crown can be located at 3 o’clock or 6 o’clock position.

S E T DAY

Pull crown to “middle” position and turn

CLOCKWISE

until correct day

appears. If day does not change, pull crown to “out” position and turn

CLOCKWISE

or

COUNTERCLOCKWISE

through necessary number of 24

hour periods until correct day appears.

S E T DAT E “ FA S T DAT E ”

3-Position Crown:

Pull crown to “MIDDLE” position and turn

CLOCK-

WISE

or

COUNTERCLOCKWISE

until correct date appears.

2-Position Crown:

Pull crown to “OUT” position and turn

CLOCKWISE

until date changes. Repeat until correct date appears. Adjust date when
month has less than 31 days. Push crown in when finished.

S E T T I M E

Pull crown all the way out and turn to correct time. Push crown in to
restart. For screw-in setting crown, push crown in while turning

CLOCK-

WISE

to tighten.

Watches with date:

Note correct time of day (A.M. or P.M.) for proper

date function.

THANK YOU FOR PURCHASING YOUR TIMEX WATCH.

EXTENDED WARRANTY
Available in U.S. only.

Extend your warranty for an additional 4 years

from date of purchase for $5. You can pay with AMEX, Discover, Visa or
MasterCard by calling 1 800-448-4639 during normal business hours.
Payment must be made within 30 days of purchase. Name, address, tele-
phone number, purchase date, and 5-digit model number required. You
can also mail a check for $5 to: Timex Extended Warranty, P.O. Box 1676,
Dept. EF, Little Rock, AR 72203.

Please read instructions carefully to understand how to oper-
ate your Timex watch.

Your model may not have all of the

features described in this booklet.

www.timex.com

W-92

905-095015

14

I

I

14

NOTE: Date may need to be manually
updated at the end of each month by
following above procedure (otherwise
it will continue to 39 and then roll
over to 00).

R O TAT I N G T I M E R I N G ( O P T I O N A L )

Position symbol (

▲

) at desired time to start or end activity.

C O M PA S S D I R E C T I O N A L R I N G ( O P T I O N A L )

To get approximate compass reading, point
hour hand at sun. Adjust ring so

S (South)

is

halfway between hour hand and 12. Adjust
every hour. Make sure hour hand is always
pointed towards the sun.

12 1

2

3

4

5

6

7

8

9

10

11

N

S

W

E

Elapsed ring

Tide ring

I N D I G L O ® N I G H T- L I G H T

Press button or crown to activate light. Patented (U.S. pat. 4,527,096 and
4,775,964) electroluminescent technology used in the INDIGLO night-light
illuminates entire watch face at night and in low light conditions.

B R A C E L E T A D J U S T M E N T

SLIDING CLASP BRACELET

Open locking plate. Move clasp to desired
bracelet length. Exert pressure while holding
locking plate and slide clasp back and forth until
it engages in grooves on underside of bracelet.
Press locking plate down until it snaps closed. Clasp can be damaged if
excessive force is used.

FOLDOVER CLASP BRACELET

Find spring bar that connects bracelet to clasp. Using a pointed tool
(Fig. 1), push spring bar in and gently twist bracelet to disengage.
Determine wrist size, then insert spring bar in correct bottom hole
(Fig. 2). Push down on spring bar, align with top hole and release to lock
in place (Fig. 3).

If your watch is water-resistant, meter marking or (

) is indicated.

Water-Resistance Depth

p.s.i.a.* Water Pressure Below Surface

30m/98ft

60

50m/164ft

86

100m/328ft

160

200m/656ft

284

*pounds per square inch absolute

WAT E R A N D S H O C K R E S I S TA N C E

WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY
BUTTONS OR PULL OUT THE CROWN UNDER WATER UNLESS YOUR
WATCH IS INDICATED AS 200 METER WATER-RESISTANT.

1. Watch is water-resistant only as long as crystal, crown and case

remain intact.

2. Watch is not a diver watch and should not be used for diving.

3. Screw-in setting crown and case back must be screwed into case to

assure water-resistance (see Set Time). (Optional)

4. Rinse watch with fresh water after exposure to salt water.

5. Shock-resistance will be indicated on watch face or caseback.

Watches are designed to pass ISO test for shock-resistance. However
avoid damaging crystal/lens.

B AT T E RY

Timex strongly recommends that a retailer or jeweler replace bat-
tery.

If applicable, push reset button when replacing battery. Battery type

is indicated on caseback. Battery life estimates are based on certain
assumptions regarding usage; battery life may vary depending on actual
usage.

DO NOT DISPOSE OF BATTERY IN FIRE. DO NOT RECHARGE. KEEP
LOOSE BATTERIES AWAY FROM CHILDREN.

BRACELET LINK REMOVAL

Removing Links:

Place bracelet upright

and insert pointed tool in opening of link.
Push pin forcefully in direction of arrow
until link is detached (pins are designed to
be difficult to remove). Repeat until desired
number of links are removed.

Reassembly:

Rejoin bracelet parts. Push pin back into link in opposite

direction of arrow. Press pin down securely into bracelet until it is flush.

SOLID LINK BRACELET

Removing Links:

Using a very small screw-

driver, remove screws by turning counter-
clockwise. Repeat until desired number of
links are removed. Do not remove links adja-
cent to clasp.

Reassembly:

Rejoin bracelet parts and

insert screw in end of opening where it was removed. Turn screw clock-
wise until tight and flush with bracelet.

Fig. 1

Fig. 2

Fig. 3