Telex MS2002 - Manual

6 Installation Unpacking The package contains the following items. Contact the shipper or your Audiocom dealer immediately if anything isdamaged or missing. Detach and fill out the registration card and return it to Telex to properly register yourMS-2002. y t Q y t Q y t Q y t Q y t Q n o it p i r c...

9 For binaural operation with two speakers: 1. Set SW3-2 to on. 2. Set SW3-5 to off. 3. Set SW3-6 to on. 4. Set SW3-7 to off. 5. Set SW3-8 to off. Balanced/Unbalanced Switches Both of the BAL - UNBAL Switches on the back panel are set at the factory to the balanced (BAL) position for usewith Audioco...

10 Cables The numbers below correspond to the cable numbers in the connection drawings on the following pages. 1. 1-channel intercom cable. Sold separately. Use Telex “ME” cables, below. Or, build per Figure 7, page 14. ME-25: 25' (7.6 m) cable with Male and Female 3-pin XLR connectors.ME-50: 50' (1...

16 Power-Up Check Plug in the MS-2002. When power is first applied to the MS-2002, it will perform a power-up reset, in which thefront panel indicators will cycle through all of their possible colors and then turn off. This verifies the generaloperation of the intercom station and indicators. The MS...

17 Figure 8 - MS-2002 Bottom View Voice-Activated Microphone (Vox) Setup If you are going to use vox, you must adjust the vox level for proper operation. If the vox level is too low, roomnoise will activate the microphone. If the Vox level is too high, the microphone will not activate when you begin...

19 Public Address (PA) If the PA output on the back panel of the MS-2002 is connected to a public address system, you can talk on thepublic address system as follows: 1. If you are using manual microphone activation instead of Vox, make sure the proper microphone switch is turned on (either Headset ...

20 Specifications General Power Requirements: AC Input: 100-240 VAC, 50/60 HzChannel Power: 24 VDC nominal (12 to 30 VDC), 65 to 150 mA MS2002 is capable of supplying 2 amps overall Dimensions: 1.75" (44.5 mm) high x 19" (483 mm) wide x 10.31" (261.9 mm) deepWeight: approximately 4.5lb (...

21 Intercom Channels, Balanced Mode (Both Back Panel and internal switches (BAL/UNBAL) must be set to same setting) Output Level: 1 Vrms nominalInput Impedance: 300 ohmsBridging Impedance: greater than 10,000 ohmsSidetone: -40 dB, 35 dB adjustable rangeCall Signaling: Send: 20 kHz ±100 Hz, 0.5 Vrms ...

22 XLR-3 Unbalanced Configuration Pinouts Pin 1: CommonPin 2: +24 VDC inputPin 3: Intercom audio high XLR-6 Unbalanced Configuration Pinouts Pin 1: CommonPin 2: Local power (12 to 15 VDC, 65 to 150 mA)Pin 3: Channel 1 +24 VDC inputPin 4: Channel 1 Intercom audio high and DC callPin 5: Channel 2 +24 ...

23 D D D D D E E E E ESCR IPTION A A A A A C C C C CTION 2 0 0 2 - S M t e s e R 1 n e t s i L d n a k l a T l l A s s e r P 1 0 0 4 S M E t e s e R 5 n e t s i L d n a k l a T l l A s s e r P n o l a n g i s t s e T l l a C p a t n e h t , A P d n a k l a T l l A s s e r P f f o l a n g i s t s e T...