Page 3 - Introduction; About This Guide; The
1 Q u i c k R e f e r e n c e Introduction Congratulations on your purchase of Symbol Technologies’ PPT 2800 Terminal! Its unique combination of features make this product superior for use in a wide range of applications. These features include: • Pocket size • Personal Information Management softwa...
Page 6 - Installing Batteries; Open the latches on the battery door and lift the battery door
4 P P T 2 8 0 0 S e r i e s Installing Batteries Before using your PPT 2800, install a lithium-ion battery: 1. Open the latches on the battery door and lift the battery door away from the PPT 2800. 2. Insert the lithium-ion battery in the battery compartment with the battery tether positioned proper...
Page 7 - Charging the Battery; Charging the Battery Using the Cradle; Insert the PPT 2800 terminal in the cradle.
5 Q u i c k R e f e r e n c e Charging the Battery Before using your PPT 2800 for the first time, charge the lithium-ion battery in the terminal for about 2 1/2 hours, using the cradle or the synchronization cable. Follow these same procedures to recharge the battery. Your terminal is equipped with ...
Page 9 - Charging the Battery Using the Synchronization Cable; Insert the cable into the bottom of the terminal.
7 Q u i c k R e f e r e n c e Charging the Battery Using the Synchronization Cable 1. Insert the cable into the bottom of the terminal. 2. Plug the power cable into a wall outlet and plug the other end into the battery charging receptacle on the side of the syn-chronization cable. Synchronization Ca...
Page 10 - Aligning the Screen; If necessary, adjust the contrast on the PPT 2800 so the
8 P P T 2 8 0 0 S e r i e s Starting the PPT 2800 Press the red power button to start the terminal. If the terminal does not power on, perform a hard reset. See Performing a Hard Reset on page 17 . As the terminal initializes its unique Flash File system, the Symbol splash screen displays for about ...
Page 11 - Using the Power Button
9 Q u i c k R e f e r e n c e 3. Tap the center of each target that appears on the screen with the tip of the stylus. 4. Follow the directions on the screen which explain how to use the stylus and pop-up menus, and allow you to set your city and time zone. Using the PPT 2800 Using the Power Button P...
Page 12 - Using the Stylus; Tap
10 P P T 2 8 0 0 S e r i e s To adjust the contrast: 1. Press and hold the Function button. 2. Press the “up” scroll button at the top of the terminal to dark- en the screen, or the “down” scroll button to lighten the screen. To turn the backlight on or off: 1. Press and hold the Function button. 2....
Page 13 - Today Screen; can see important information for the day.
11 Q u i c k R e f e r e n c e Today Screen When you turn on your terminal for the first time each day (or after 4 hours of inactivity), the Today screen appears. You can also display it by tapping , then Today. On the Today screen, you can see important information for the day.
Page 14 - Navigation Bar and Command Bar
12 P P T 2 8 0 0 S e r i e s Navigation Bar and Command Bar The navigation bar at the top of the screen displays the active program and current time, and allows you to switch to programs and close screens. The command bar at the bottom of the screen contains menus and buttons to perform tasks in pro...
Page 15 - Input Methods
13 Q u i c k R e f e r e n c e Input Methods Enter information in any program by typing with the soft keyboard or writing using Character Recognizer. The Character Recognizer input panel is divided into three writing areas. Letters written in the left area (labeled ABC) create uppercase letters and ...
Page 18 - Resetting Your PPT 2800 Terminal; If your PPT 2800 terminal stops responding to input, reset it.; Performing a Soft Reset
16 P P T 2 8 0 0 S e r i e s Resetting Your PPT 2800 Terminal If your PPT 2800 terminal stops responding to input, reset it. Performing a Soft Reset A soft reset restarts the terminal and saves all stored records and entries. Caution: Files that remain open during a soft reset may not be retained. C...
Page 19 - Performing a Hard Reset
17 Q u i c k R e f e r e n c e Performing a Hard Reset A hard reset also restarts your PPT 2800 terminal, but erases all stored records and entries. Therefore, never perform a hard reset unless a soft reset does not solve your problem. Note: You can restore any data previously synchronized with your...
Page 20 - Troubleshooting; PPT 2800 terminal does not turn on:; ers; properties dialog box (under; Start
18 P P T 2 8 0 0 S e r i e s Maintaining the PPT 2800 For trouble-free service, observe the following tips when using your PPT 2800: • Do not scratch the screen. Use the supplied stylus or plastic-tipped pens intended for use with a touch-sensitive screen. Never use a pen or pencil or other sharp ob...
Page 22 - , select the unused program and tap
20 P P T 2 8 0 0 S e r i e s • If you have installed additional applications on your PPT 2800 terminal, remove them to recover memory. Select Start , then Settings , and select the System tab. Tap Re- move Programs , select the unused program and tap Re- move. Beamed data does not transmit: • Confir...
Page 26 - Regulatory Information; Radio Frequency Interference Requirements; Radio Frequency Interference Requirements - Canada
24 P P T 2 8 0 0 S e r i e s refer to the address provided in the documentation for the SYSTEM. FOR THE LIMITED WARRANTIES AND SPECIAL PROVISIONS PERTAINING TO YOUR PARTICULAR JURISDICTION, PLEASE REFERTO YOUR WARRANTY BOOKLET INCLUDED WITH THIS PACKAGE OR PROVIDED WITH THE SOFTWARE PRINTED MATERIAL...
Page 27 - CE Marking and European Union Compliance; Applicable Directives; RF Devices
25 Q u i c k R e f e r e n c e CE Marking and European Union Compliance Products intended for sale within the European Union are marked with the CE Mark which indicates compliance to applicable Directives and European Normes (EN), as follows. Amendments to these Directives or ENs are included: Appli...
Page 28 - ARNING
26 P P T 2 8 0 0 S e r i e s Technologies equipment not expressly approved by Symbol Technologies could void the user ’s authority to operate the equipment. The Spectrum24 equipment is intended for use throughout the European Economic Area, but it’s authorization for use in France is restricted as f...
Page 29 - Laser Devices; Scanner Labeling
27 Q u i c k R e f e r e n c e Laser Devices Symbol products using lasers comply with US 21CFR1040.10, and IEC825-1:1993, EN60825-1:1994+A11:1996. The laser classification is marked on one of the labels on the product. Class 1 Laser devices are not considered to be hazardous when used for their inte...
Page 31 - Battery Caution
29 Q u i c k R e f e r e n c e Battery Caution Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recom-mended by the manufacturer. Dispose of used batter-ies according to the manufacturer's instructions.
Page 32 - DECLARATION OF CONFORMITY
30 P P T 2 8 0 0 S e r i e s DECLARATION OF CONFORMITY We, Symbol Technologies, Inc. of One Symbol Plaza, Holtsville, NY 11742-1300, USA declare under our sole responsibility that the product Spectrum24, LA3021, Type II Radio Card Spectrum24, LA302C, Type II Radio Card Spectrum24, LA302T, Type II Ra...
Page 35 - Warranty; Warranty Coverage and Procedure
Q u i c k R e f e r e n c e Warranty Symbol Technologies, Inc. (“Symbol”) manufactures its hardware products in accordance with industry-standard practices. Symbol warrants that for a period of twelve (12) months from date of shipment, products will be free from defects in materials and workmanship....
Page 36 - Service Information
72-52773-01 Revision A — May 2001 Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300 Service Information Before you use the unit, it must be configured to operate in your facility’s network and run your applications. If you have a problem running your unit or using your equipment, ...
