SVAT CLEARVU11 - Manual

SVAT ELECTRONICS now you can see CLEARVU11 3 INTRODUCTION WHAT IS INCLUDED • Mounting Hardware • Quick Start Guide • Instruction Manual • 1 Year Warranty • 24/7 Online/ Toll Free Support 15 " LCD DVR with 320GB Hard Drive 4 Outdoor Night Vision Cameras 4 Window Warning Stickers 8.5 ft. DC12V Pow...

SVAT ELECTRONICS now you can see CLEARVU11 4 BUTTON FUNCTIONS AND CONNECTIONS 2 3 4 5 13 14 15 1 6 7 8 9 10 11 12 16 17 18 19 20 24 23 22 21 29 28 27 26 25 30 15" LCD/DVR

SVAT ELECTRONICS now you can see CLEARVU11 6 TIPS BEFORE ASSEMBLING BASIC SETUP • The camera should be installed between 8 and 13ft above the area to be monitored. • Ensure there are no obstructions in the camera’s view, to maximize viewing area. • Ensure that the sunshade is positioned to avoid gla...

SVAT ELECTRONICS now you can see CLEARVU11 7 BASIC SETUP MOUNTING THE CAMERA 1. Screw the mounting bracket into the camera’s mounting hole, turning it clockwise. 2. Mount the camera in the desired location no more than 60 feet from the DVR unless you have purchased additional wiring. You may wall mo...

SVAT ELECTRONICS now you can see CLEARVU11 8 POWERING THE SYSTEM 1. Insert the power supply wire into the rear DC 12V Port on the LCD/DVR. 2. Plug the mouse into the PS2 port at the back of the LCD/DVR (recommended). 3. Insert the power cord into the power supply. 4. Plug the power cord into a power...

SVAT ELECTRONICS now you can see CLEARVU11 9 GENERAL INFORMATION MAIN SCREEEN NOTE: The following instructions are described for use with the remote control. Front panel buttons may not match with the following directions. It is recommended that you use the included mouse or remote for full function...

SVAT ELECTRONICS now you can see CLEARVU11 10 TEXT INPUT (To be used with remote control) There are certain circumstances where the system requires the user to enter text, such as system login, camera title setup, and so on. Below are the instructions on how to enter text using the remote control: 1...

SVAT ELECTRONICS now you can see CLEARVU11 11 GENERAL INFORMATION USING THE MOUSE To make use of the mouse when operating the DVR please move the cursor to the bottom of the screen. You will see the icons of the mouse functions displayed. When you move the cursor over the icons, you will see the nam...

SVAT ELECTRONICS now you can see CLEARVU11 12 GENERAL INFORMATION MOTION DETECTION SETUP USING THE MOUSE PTZ SETUP USING THE MOUSE The PTZ camera functions and their corresponding icons are shown below. VIDEO ADJUSTMENT ICONS USING THE MOUSE COMMON ICONS Move the cursor to Menu -› Setup -› Camera -›...

SVAT ELECTRONICS now you can see CLEARVU11 13 MAIN MENU While in the split-window display, press MENU (MENU/ESC) to call up Menu display as shown. We recommend using the mouse. With the mouse the menu is found by dragging the cursor to the bottom of the screen. If you are using the remote, simply pr...

SVAT ELECTRONICS now you can see CLEARVU11 14 In Login/Logout menu, follow the Text Input method to enter the Login name and Password • Press ▲▼ to highlight login name, Use the text input method to enter the login name. Press Enter • Press ▲▼ to highlight password name, Use the text input method to...

SVAT ELECTRONICS now you can see CLEARVU11 15 VIDEO ADJUSTMENT In Menu display, press ▲▼ to change the highlighted option to Video Adjustment, and then press ENTER to call up Video Adjustment display as shown. There are 4 items which can be adjusted, including Brightness, Contrast, Hue, and Saturati...

SVAT ELECTRONICS now you can see CLEARVU11 18 CAMERA SETUP In Setup Menu display, press ▲▼ to change the highlighted option to Camera , and then press ENTER to call up Camera Setup display as shown. The Camera Setup allows the administrator to define the attributes for each camera. Up to 4 cameras c...

SVAT ELECTRONICS now you can see CLEARVU11 20 MAIN MENU MOTION DETECTION The Clearvu11 has bulit in motion detection available for each camera . Press ENTER or +/- to check/uncheck this item. The default setting is “  ” - checked. MOTION SETTINGS This is the link used to setup the motion settings f...

SVAT ELECTRONICS now you can see CLEARVU11 22 MAIN MENU DETECTION SETTINGS This menu allows you to setup the motion detection settings, including detection area and sensitivity, when motion is detected for this camera. 10 being the most sensitive and 1 being the least sensitive. Press ENTER in Setti...

SVAT ELECTRONICS now you can see CLEARVU11 23 MAIN MENU DWELL TIME Dwell time refers to how long the video of the motion detection will stay on the screen. If Call By Event is set to Motion, Alarm, or Both. Press +/- buttons to adjust the value (3 seconds-60 minutes, discrete) to choose the “dwell t...

SVAT ELECTRONICS now you can see CLEARVU11 24 MAIN MENU The general operations are as below: • ▲▼◄► - Press these buttons to select the items. The display will scroll left/right if the selected item is not shown on the screen. • Numeric (CH1-CH4) - Press these buttons to select the camera. • COPY ( ...

SVAT ELECTRONICS now you can see CLEARVU11 25 MAIN MENU • Post-record – to define how long after this alarm input is triggered the Focus Camera shall be intensively recorded at Event Record IPS. Press +/- buttons to adjust the value (0 second - 60 minutes, discrete). • Alarm Out – to define which Al...

SVAT ELECTRONICS now you can see CLEARVU11 27 MAIN MENU SCHEDULED RECORD SETUP In Setup Menu display, press ▲▼ to change the highlighted option to Scheduled Record, and then press ENTER to call up Scheduled Record Setup as shown The Scheduled Record Setup allows the administrator to define when and ...

SVAT ELECTRONICS now you can see CLEARVU11 28 MAIN MENU • Normal – normal record mode, including, A/V (Audio/Video), V (Video only), or No (No Video). Press +/- buttons to change the value. The general operations are as below: • ▲▼◄► - Press these buttons to select the items. The display will scroll...

SVAT ELECTRONICS now you can see CLEARVU11 31 MAIN MENU PASSWORD SETUP In Setup Menu display, press ▲▼ to change the highlighted option to Password, and then press ENTER to call up Password Setup menu as shown. The Password Setup allows the administrator to add new users, delete existing ones, and/o...

SVAT ELECTRONICS now you can see CLEARVU11 32 SYSTEM SETUP In Setup Menu display, press ▲▼ to change the highlighted option to System , and then press ENTER to call up System Setup as shown. The System Setup allows the administrator to set the system time, time zone, time synchronization, language, ...

SVAT ELECTRONICS now you can see CLEARVU11 34 NETWORK SETUP The general operations are as below: • ▲▼◄►- Press these buttons to select the items. • ESC (MENU/ESC) - Press this button to escape from this screen, and return to Setup Menu display. If the Save dialog is shown, press ENTER to exit and sa...

SVAT ELECTRONICS now you can see CLEARVU11 36 ADVANCED NETWORK SETUP In Network Setup, press ENTER to call up Advanced Network Setup as shown when the highlighted option is Adv. The Advanced Network Setup allows the administrator to set advanced network parameters. If the user is not familiar with n...

SVAT ELECTRONICS now you can see CLEARVU11 37 SOFTWARE UPGRADE (Administrator mode only) In Menu display, press ▲▼ to change the highlighted option to Software Upgrade , and then press ENTER to call up Software Upgrade display as shown. FACTORY DEFUALTS If you choose to reset your DVR, highlight the...

SVAT ELECTRONICS now you can see CLEARVU11 38 NETWORKING GUIDE NOTE: This guide was created using a cable modem and some procedures will be slightly different depending on your hardware. If you are using a DSL modem, you may need to enter your PPPoE settings into the DVR (User name and password prov...

SVAT ELECTRONICS now you can see CLEARVU11 39 NOTE: If you look at the router there should be a green “link” light indicating that the DVR is properly connected to the port that it was plugged into. If this light is on, you can proceed to finding the DVR’s IP Address. FINDING THE DVR’S IP ADDRESS On...

SVAT ELECTRONICS now you can see CLEARVU11 40 PREPARING YOUR COMPUTER FOR VIEWING THE DVR Any computer that is accessing the DVR will need to be configured to install and run ActiveX controls and the Microsoft Visual C++ 2005 SP1. (This will require you to be logged into the computer as an Administr...

SVAT ELECTRONICS now you can see CLEARVU11 41 Method 2: 1. Open Internet Explorer. Go to the drop down menu in the Tools area and select Internet Options. 2. Select the Security Tab and then click on the Custom Level button in this tab. 3. Change the ActiveX Settings to the ones seen in the image: •...

SVAT ELECTRONICS now you can see CLEARVU11 42 INSTALL THE ACTIVEX CONTROLS AND MICROSOFT VISUAL C++ 2005 SP1 After typing the IP address into the Internet Explorer address bar and pressing ENTER: 1. There will be a yellow information bar that pops up below the address bar in Internet Explorer. Click...

SVAT ELECTRONICS now you can see CLEARVU11 43 CONFIGURING YOUR ROUTER (PORT FORWARDING) TO VIEW THE DVR EXTERNALLY * Your router will need to be configured properly before being able to view the DVR from a location different than the DVR* Port forwarding is a necessary step that opens a path on your...

SVAT ELECTRONICS now you can see CLEARVU11 45 4. Select the Virtual Server tab. • Select the Enabled check box.• In the Name field type in “DVR80”.• In the Private IP field enter the DVR’s IP address. • In the Protocol field, select Both (This will enable both TCP and UDP). • In the Private port ent...

SVAT ELECTRONICS now you can see CLEARVU11 46 DYNAMIC DNS Instead of having to remember and enter your IP address every time you want to access the DVR online, you can set up the DVR so that it is associated with a website URL (domain name) that is easy for you to remember. 1. Open internet explorer...

SVAT ELECTRONICS now you can see CLEARVU11 48 To configure the DVR to work with DDNS: 1) Press Menu and Select Login / Logout2) Type in the username and password. (default username is “aa”. Default password is “11”3) Select Setup4) Select Network5) Change the Net Type to static. Note that the DHCP I...

SVAT ELECTRONICS now you can see CLEARVU11 52 SEARCH MENU There are three ways to search the recorded video/audio for playback:(a) Search by time,(b) Search by event,(c) Search archived files. In split-window display, press SEARCH button to call up SearchMenu display as shown. The user’s operations ...

SVAT ELECTRONICS now you can see CLEARVU11 55 SEARCH BY EVENT The screen for Search By Event - Log display, is shown below: There are four different types of event logs, including Alarm, Motion, Video Loss, and System. Up to 1000 of the most recent event logs can be stored in the system. The general...

SVAT ELECTRONICS now you can see CLEARVU11 56 SEARCH MENU The Backup display will be shown. Please note that this kind of backup without playback is performed in the background, and the user can still do almost all the operations. Playback/Archive For Search By Event In Log display, press ENTER to e...

SVAT ELECTRONICS now you can see CLEARVU11 57 NOTE : The format of the filename is camNN-YYYYMMDD-hhmmss.h264, where NN stands for camera number, YYYY year, MM month, DD date, hh hour, mm minute, and ss second. Playback For Archived Files In Search Archived Files display, press ENTER to enter Archiv...

SVAT ELECTRONICS now you can see CLEARVU11 58 PDA/MOBILE PHONE REMOTE VIEWING The following is a brief description of each item and its specific operation. - will apply your changes - Q1, 1-4 will choose whether to view quad screen or an individual camera - IS-30S will choose your refresh rate - Ala...

SVAT ELECTRONICS now you can see CLEARVU11 59 CD SOFTWARE AND ARCHIVE VIEWING To run the HEM Player under Microsoft® Windows® XP or Windows® 2000, please select Start >Programs->Hyper Electronics Mappers->HemPlayer, and the screen will be shown as below.Since this utility is a free player u...

SVAT ELECTRONICS now you can see CLEARVU11 60 M4V/H.264 TO AVI CONVERSION UTILITY To run the M4V/H.264 to AVI Conversion Utility , please select Start->Programs->Hyper Electronics Mappers->M4V2AVI or double-click on the file AVI_ Converter.EXE , and the screen will be shown like the one to ...

SVAT ELECTRONICS now you can see CLEARVU11 61 TROUBLESHOOTING GUIDE Cannot see icons or access the menu (using the mouse) • Move the mouse cursor to the bottom of the screen. A task bar of available options will appear. You will need to login before you can utilize most of the functions. Some icons ...

SVAT ELECTRONICS now you can see CLEARVU11 65 TROUBLESHOOTING GUIDE “Warning: Connect to device DVR#........... Failed message while using Internet Explorer.” when I try to view the software over the web. • If you see this dialogue box using the Internet Explorer web viewing software:• It means that...

SVAT ELECTRONICS now you can see CLEARVU11 66 SPECIFICATIONS System O.S Embedded Linux 2.6 Multiplex Sixfold operation - simultaneous record, live, playback, backup, control, & remote access Certification FCC, CE, LVDS, etc. FCC, CE, LVDS, etc. Video Format NTSC/EIA or PAL/CCIR Input 4-CH, BNC, ...

SVAT ELECTRONICS now you can see CLEARVU11 70 NOTES AREA