Page 2 - Safety; Important Safety Instructions
Safety WARNING – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Important Safety Instructions 1. Read Instructions 2. Keep these Instructions 3. Heed all Warnings. 4. Follow all Instructions 5. Do not use this apparatus near water. 6. Clean only with ...
Page 3 - Contents; System Design, Installation and; For more information on this and other Sunfire; Introduction
Contents Important Safety Instructions ...................... Introduction ................................................. 4 Features ...................................................... 7 System Design, Installation and Connections .............................................. 10 Connectors/Pi...
Page 4 - Unpacking
Introduction The Olé ® -SF Film Interactive Touchpad (FIT) is a revolutionary in-wall controller for your Sunfire receiver or processor. Using a photographic film overlay instead of hard buttons, it marries the beauty of a touchscreen with the simplicity of a keypad –seamlessly controlling all major...
Page 7 - Features; Top Panel
Features 1. Mounting Screw (x 4) Use these screws to mount the touchpad into a standard 3 cu in. double-gang electrical box. . Program Button This button is for future use. 3. Light Sensor When this sensor is enabled, the Olé-SF backlight will brighten or dim depending on the room's ambient light co...
Page 9 - Switch; Rear Panel
14. Z•NET/VIA!NET Switch You must set this switch to VIA!NET for use with Sunfire receivers and processors. 1. System RJ-4 Jack Connect this jack with Cat- cable to the TP1 or TP RJ-4 con- nectors on the rear panel of your Sunfire receiver or processor. 16. Local IR Port This port allows the connect...
Page 11 - Mounting Height
Rough-In Roughing-in the Olé-SF requires careful attention to the design plan made previously. Review the previ- ous page and make a list of things to factor in to specific mounting loca - tions, before deciding exactly where to place the unit. In order to avoid Electro-Magnetic Interference (EMI), ...
Page 13 - Local IR Interface Port
Local IR Interface Port Use this connector when utilizing the Olé-SF’s local control features, such as local source control, local IR sensors, or sense-enabled auto- mated sequences. Warning: The connection labeled “+1 Volts Out” is a voltage output. Do not con- nect a power supply to this connectio...
Page 14 - Local IR Input
Local IR Input The Local IR-RECEIVER IN is typically used to connect an external IR sensor to the touchpad. Typical applications include a plasma- friendly IR sensor placed near a TV, or an auxiliary IR sensor placed in an area more convenient than the location of the touchpad. IR signals that are r...
Page 15 - Local Sense In
Local Sense In The LOCAL SENSE IN port allows a contact-closure to trigger IR se- quences programmed into the Olé- SF using SunTools. Use a motion sensor to activate a contact-closure and cause automated actions such as system power on, drapes closed, and lights dimmed, for example. Connect LOCAL SE...
Page 17 - Home Theater Control
CAT-5 USE EITHER CONNECTION MAIN ZONE SPEAKERS MAIN ZONE Olé-2SF Home Theater Control (PC required) The Olé-SF is perfectly suited as an in-wall Home Theater controller. You may want to include one by the entrance to startup or shutdown the system. In this case, you will need to connect your Olé-SF ...
Page 18 - Programming; To download a SunTools
Programming The Olé-SF must be pro- grammed with Sunfire’s SunTools setup software using a PC running Windows XP. Downloads are facili- tated through the USB download port on the front of the unit. Note: A standard USB-A to USB- mini-B cable must be utilized for programming and is not included with ...
Page 20 - Specifications
Specifications Viewing Angle 180° up/down,180° left/right Operating Temp 3°F-104°F / 0°C-40°C OLED Display Type: 2” Organic LED (OLED) Colors: K Resolution: 160 pixels (W) x 128 pixels (H) Connections System Port: RJ-4Interface Port: -position screw terminalDownload Port: Mini USB Wiring Requirement...
Page 21 - Troubleshooting; Power
Troubleshooting Power Symptom Cause Solution Olé-SF does not power up. 1. RJ-4 plug crimped incorrectly; or wiring pinout of RJ-4 reversed. Verify wiring pinout and RJ-4 crimp. Correct by re-crimping RJ-4 to Cat- cable. . Break in Cat- between Zone and “Head-End”. Check RJ-4 to RJ-4 con- nections wi...
Page 22 - IR
IR Symptom Cause Solution No control of IR sources. 1. Programming: missing or incorrect IR commands. Verify and correct program- ming. Test IR commands from SunTools. . Wiring: Incorrect wiring between Zone and ‘Head-End”. Verify and correct wiring. 3. Wiring: IR emitter connected to wrong source I...
Page 23 - Sunfire Warranty; Service Assistance
Sunfire Warranty 3 Sunfire, LLC is proud of its products that have been built with care using advanced technology and premium component parts. Your unit has been crafted to perform properly for many years. Sunfire offers the following Warranty to you, the owner of a new Sunfire product:The Sunfire W...
