Sun Microsystems 1500 - Manual
Sun Microsystems 1500 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – DIMM Location and Identification; lists the acceptable DIMM pair configurations.; Removing DIMMs; “Powering Off the Workstation” on page 10-4; DIMM Configurations; DIMM
- Page 3 – Identifying the Rear Fan; shows the location of and identifies the rear fan.; Note –; Rear Fan Location and Identification
- Page 4 – Smart Card Reader Location and Identification; Removing the Smart Card Reader; Disconnect the interface cable from the motherboard.; The cable is connected on the motherboard at; Smar t card reader
- Page 5 – Identifying the DVD-ROM Drive Interface Cable; IDE PWR; DVD-ROM Drive Interface Cable Connection; Removing the DVD-ROM Drive Interface Cable; Power off the system and open the chassis.; Connector
- Page 6 – Disconnect the IDE power cables from the upper hard drive; Disconnecting the IDE Power Cable From the Hard Drive(s); See; Disconnecting the IDE Power Cable From the DVD-ROM Drive; Interface cable
- Page 7 – Identifying the Hard Drive Interface Cable; Hard Drive Interface Cable Connection
- Page 8 – Pressing the Catch on the Rear Fan Bracket; Sliding the Duct Up; opposite of its original position.; Guide rails
- Page 9 – Bezel Location and Identification
- Page 10 – Pressing Down on the Clip Latch; b. Slide the clip to unhook the end opposite the latch.; This relieves clip pressure.; Releasing the CPU Fan and Heatsink Assembly Clips
- Page 11 – Identifying the Battery; shows the location of and identifies the battery.; Battery Location and Identification; lists the battery specifications.; Removing the Battery; Battery Specifications; Battery clip
- Page 12 – Identifying the PCI Card Slots
- Page 13 – Removing Cables From the Routing Clips; Disconnect the power and signal cables.; Remove the motherboard fastening screws.; Routing clip
- Page 14 – Removing the PCI Card Support; Do not use the chassis cross brace as a handle.; Installing the PCI Card Support; Refer to “Removing the Access Panel” on page 10-12; Identify where the PCI card support is to be installed.; Pivot tab
- Page 15 – Reconnect any other external peripherals.
Sun Microsystems, Inc.
4150 Network Circle
Santa Clara, CA 95054 U.S.A.
650-960-1300
Send comments about this document to:
Sun Blade™ 1500
Service, Diagnostics, and
Troubleshooting Manual
Part No. 816-7564-10
April 2003, Revision A
EXA
MP
LE
DO
CU
ME
NT
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Chapter 11 Replacing the Motherboard and Associated Components 11-3 FIGURE 11-1 DIMM Location and Identification Depending upon the configuration of your workstation, you can either add orreplace memory. In either case, the new DIMMs must meet the Sun workstationrequirements. TABLE 11-1 lists the ac...
Chapter 13 Replacing Chassis Components 13-15 You can also view an animated version of these instructions by clicking onthis film icon. 13.3.1 Identifying the Rear Fan The front and rear fans on the Sun Blade 1500 workstation are contained in greenbrackets. Both fans must be operating to adequately ...
12-16 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 FIGURE 12-13 Smart Card Reader Location and Identification 12.3.2 Removing the Smart Card Reader 1. Power off the system, open the chassis, and remove the bezel. Refer to: ■ “Powering Off the Workstation” on page 10-4...
