State Water Heaters FORCE 90TM - Manual
State Water Heaters FORCE 90TM – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Front
Size:
8.5"W x 11"H
Job
#:
SWHC 111787
File
Name:
111787_Force90_SS.ai
Printing
&
Finishing:
4/cProc-Offset
Colors:
C
M
Y
K
DIE
Printout Size
100%
Updates:
hd3.20/21.06, hd3.31.06,
jpc4/3/06,hd4.04.06,hd4.10/11.06,
hd4.13.06,hd4.17.06,hd4.21.06,
JVSpf.4.26.06
This printout is for indicating
color breaks only.
Do not use for color matching.
Do not measure for accuracy.
Revision:
10
T i m e :
3 P M
F
ORCE 90
™
90% EFFICIENT
Power-Vent Commercial Gas Water Heater
The 50-gallon, 76,000 BTU Force 90 light-duty commercial gas water heater is equipped with a fully submerged, spiral-shaped condensing heat
exchanger. This design provides much greater heat transfer surface than a standard straight flue tube, resulting in 90% thermal efficiency and
higher hot water output than comparable 80% efficient water heaters. With 22" diameter, the 50-gallon Force 90 can be installed in less space than
a 75-gallon unit and delivers greater recovery and lower operating costs.
Power-Vent Design for Installation Versatility
• Modular blower, with 120 volt, 60Hz electrical system (5 amps or less), 6-foot cord with
standard
3-prong
connector
• Combined horizontal and vertical vent runs terminating through outside wall,
using Schedule 40 PVC pipe as follows:
- 2" pipe allows vent runs up to 25 equivalent feet
- 3" pipe allows vent runs up to 65 equivalent feet
- 4" pipe allows vent runs up to 128 equivalent feet
• Supplied with PVC pipe and elbows to connect heat exchanger outlet to blower,
including condensate elbow and drain
• PVC Vent Attenuation Assembly (VAA) supplied to help ensure extra-quiet operation
Side-Mounted Taps for Recirculating Systems
• Hot and cold “side taps” allow Force 90 to be used for “combination” systems
for water heating plus space heating, radiant floor heating or other applications
requiring a recirculating hot water loop
• Plugs for recirculating taps are factory installed
Intelli-Vent
®*
Gas Control with Silicon Nitride Hot Surface Ignitor
• Premium-grade hot surface ignitor eliminates standing pilot
• Electronic circuitry provides superior system diagnostic capabilities plus extremely
precise temperature control
• 180°F maximum temperature setting
Glass Lined Tank with Two Magnesium Anode Rods
• Provides superior protection against corrosion
• Glass lining protects all “water side” tank surfaces plus inside of internal heat
exchanger exposed to condensate
Low-NOx Green Choice
®
Burner
• Reduces NOx emissions up to 33%, complies with Southern California and Texas
requirements
PEXAN
™
Diffuser Dip Tube
• Helps reduce lime and sediment buildup, maximize hot water output
• PEXAN cross-link polymer withstands long-term exposure to temperatures up to 400°F
Factory-Installed Temperature and Pressure Relief Valve
Maximum Hydrostatic Working Pressure: 150 psi
Meets ASHRAE/IESNA 90.1-1999
• Design-certified by UL (Underwriters Laboratories) according to ANSI Z21.10.3-CSA4.3
standards governing storage-type water heaters
Three-Year Limited Tank Warranty
• Consult written warranty shipped with water heater or contact State for complete
warranty
information
For Additional Technical Information,
PHONE 800-365-0024
State Industries, Inc.
500 Tennessee Waltz Parkway, Ashland City, TN 37015
www.statewaterheaters.com
Page 1 of 2
SCGSS00806
* Intelli-Vent is a registered trademark of the Emerson Electric Company
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
