Page 2 - EC Declaration of conformity; Declaration of incorporation
EC/EN (1001) 5.1 1 EC Declaration of conformity (Directive 2006/42/EC, appendix II-A) Manufacturer SPX Process Equipment NL B.V.Dr. A.F. Philipsweg 519403 AD AssenThe Netherlands hereby declares that all pumps member of productfamilies CombiBloc, CombiBlocHorti, CombiChem, CombiDirt, CombiFlex(U)(B)...
Page 4 - CombiPro
CR/EN (1004) 4.0 3 CombiPro Instruction manual CombiPro All technical and technological information in this manual as well as possible drawings made available by us remain our property and shall not be used (otherwise than for the operation of this pump), copied, duplicated, made available to or bro...
Page 6 - Table of Contents
CR/EN (1004) 4.0 5 CombiPro Table of Contents 1 Introduction 9 1.1 Preface 9 1.2 Safety 9 1.3 Guarantee 10 1.4 Inspection of delivered items 10 1.5 Instructions for transport and storage 10 1.5.1 Weight 10 1.5.2 Use of pallets 10 1.5.3 Hoisting 11 1.5.4 Storage 11 1.6 Ordering parts 12 2 General 13 ...
Page 10 - Introduction
CR/EN (1004) 4.0 Introduction 9 CombiPro 1 Introduction 1.1 Preface This manual is intended for technicians and maintenance staff and for those who are in charge of ordering spare parts. This manual contains important and useful information for the proper operation and maintenance of this pump. It a...
Page 14 - General
CR/EN (1004) 4.0 General 13 CombiPro 2 General 2.1 Pump description The CombiPro represents a range of horizontal "heavy duty" centrifugal pumps. The design of this range of pumps is based on the guidelines for: "Centrifugal Pumps for Petroleum, Petrochemical and Natural Gas Industries...
Page 20 - Installation
CR/EN (1004) 4.0 Installation 19 CombiPro 3 Installation 3.1 Safety • Read this manual carefully prior to installation and commissioning. Non-observance of these instructions can result in serious damage to the pump and this will not be covered under the terms of our guarantee. Follow the instructio...
Page 26 - Commissioning
CR/EN (1004) 4.0 Commissioning 25 CombiPro 4 Commissioning 4.1 Inspection of the pump Check whether the pump shaft turns freely. Do this by turning the shaft end at the coupling a few times by hand. 4.2 Inspection of the motor Check whether the fuses have been mounted. 4.3 Pumps with oil-bath lubric...
Page 28 - Maintenance
CR/EN (1004) 4.0 Maintenance 27 CombiPro 5 Maintenance 5.1 Daily maintenance • Regularly check the oil level, see figure 7. No water should get into the terminal box of the electric motor when the pump room is sprayed clean! Never spray water on hot pump parts! The sudden cooling down may cause th...
Page 30 - Problem solving
CR/EN (1004) 4.0 Problem solving 29 CombiPro 6 Problem solving Faults in a pump installation can have various causes. The fault may not be in the pump, it may also be caused by the pipe system or the operating conditions. Firstly, always check that installation has been executed in accordance with t...
Page 32 - Disassembly and assembly
CR/EN (1004) 4.0 Disassembly and assembly 31 CombiPro 7 Disassembly and assembly 7.1 Precautionary measures Take adequate measures to avoid that the motor is started while you are working on the pump. This is especially important for electric motors with remote control: • Switch the operating swit...
Page 40 - Dimensions
CR/EN (1004) 4.0 Dimensions 39 CombiPro 8 Dimensions 8.1 Pump dimensions Connections Connections (optional) Figure 12: Pump dimensions. B M Oil drain ½ BSP BV Oil filling plug ½ NPT B D Inlet oil chamber jacket ½ NPT B E Outlet oil chamber jacket ½ NPT B N Drain oil chamber jacket ½ NPT DN1 DN2 ab a...
Page 44 - Parts
CR/EN (1004) 4.0 Parts 43 CombiPro 9 Parts 9.1 Ordering parts 9.1.1 Order form You can use the order form included in this manual for ordering parts. When ordering parts always quote the following data: 1 Your address . 2 The quantity, the item number and the description of the part. 3 The pump numb...
Page 52 - 0 Technical data
CR/EN (1004) 4.0 Technical data 51 CombiPro 10 Technical data 10.1 Tightening moments 10.1.1 Tightening moments for bolts and nuts ! For nuts for pump casing (item 0810), see paragraph 10.1.3 "Torques settings for nuts for pump casing"! 10.1.2 Tightening moments for cap nut Table 5: Tighteni...
Page 64 - Index
CR/EN (1004) 4.0 63 CombiPro Index A Accessories . . . . . . . . . . . . . . . . . . . . . . . . . 23Application area . . . . . . . . . . . . . . . . . . . . . 17Applications . . . . . . . . . . . . . . . . . . . . . . . . . 13 B Back-Pull-Out unit assembling . . . . . . . . . . . . . . . . . . . . ...
Page 66 - Order form for spare parts
ORDFORM (0804) 3.1 EN 65 Order form for spare parts Your order will only be dealt with if this order form has been correctly completed and signed. FAX Nr. ADD R ESS Order date: Your order number: Pump type: Execution: Quantity Item. No. Part Article number pump Delivery address: Invoicing address: O...