Speco Technologies HTSD10X - Manual

Page 2 - CONTENTS

2 Warning & Caution What ’s in the Box? General Features Names of Each Part Installation A. Connection Methods B. Ceiling Mount Type C. Embedded Mount Type Quick Operating Keys Diagnostic OSD Menu Setting A. OSD Menu Table B. DOME SET C. CAME RA SET D. PRESET E. AUTO SCAN F. TOUR SET G. PRIVACY ...

Page 3 - Warning

3 WARNING & CAUTION If you fail to read this information and handle the product incorrectly, serious injury may occur. 1. Camer a 2. Screws ( Ø4x16 screw 5EA ) 3. Terminal block (5pin 2EA) 4. Manual 5. Screw C ap (2 EA) Never install the product in area exposed to oil or gas. Never install the p...

Page 4 - GENERAL FEATURES; Indoor / Outdoor applications

4 GENERAL FEATURES 100X Zoom Mini Speed Dome 10X Opt ic al Zoom with 10X digit al zoom ± 0.02 ° dome sys tem accu racy W ith 0.1 ° t echnic al accur acy, cam era provides exc ellent sensitive and delic at e cont rolling on pr eset m ode by adapting 1/4 m icro st ep and twin gear syst em 360° End les...

Page 5 - N A MES OF EA CH PA RT

5 N A MES OF EA CH PA RT 1. S urface Mount Adaptor 2. C ap S crew ( PT3/4 , 2EA ) 3. D ip S witch 4. Term inal Block 5. Main body

Page 6 - A. CONNECT ION METHOD; Don’t screw too tightly. It can be the cau se of defect.; INSTALLATION

6 A. CONNECT ION METHOD A-1 1. Loosen the screws on the domes cover and remove it from the base. (Screws will not come out) 2. Loose n the screws which connect the mount cover and Main base and separate the dome cover from the main base. (S crews will not come out) 3. C onnect power ( 12 VDC 1.5 A )...

Page 8 - QUICK OPERATING KEYS

8 1-64 + preset and 101~200 + preset are use d for preset and 65-100 + preset used f or functions. For example, to enter OSD MENU, press the button 95 +PRESET. <Quick Operation Key Table 1, Pelco - D, P> Number Note Function 1 ~ 64, 100~200 +Preset PRESET Executing Preset 1 ~ 64 65 + Preset PR...

Page 9 - DIAGNOSTIC

9 When the Power is turned on a DIAG ONOSTIC is operated. The follow ing mes sages are displayed on the m onitor. A. Pan Origin Test Zero poi nt of Pan is f ounded after Panni ng test. B. Tilt O rigin Test Zero poi nt of Tilt is founded after Tilting test. C . TX connection Test C ountdown from 60 s...

Page 10 - EEPROM CHECKING”; EEPROM OK”; OSD MENU SETTING

10 If all the above Tests are OK, “ EEPROM CHECKING” and “ EEPROM OK” is displayed and the camera is ready to operate. A. OSD MENU TABLE OSD MENU SETTING MAIN MENU DOME SETUP CAMERA SET AUTO SCAN TOUR PRAVACY PATTERN ALARM SECTOR EXIT DOME SET CAMERA ID : CAM1 □□□□□□□□□□□□ RECOVER : OFF MANUAL SPEED...

Page 11 - DEFAULT SETTING

11 To enter the OSD Menu, press the button 95 + PRESET. * Use the joystick “up - down” to move the position and “left - right” to make selection B. Dome Setup To enter the Dome setup, move the joystick right to move the cursor . B-1. DOME SET - CAMERA ID To set camera ID , select up to 16 characters...

Page 12 - DOME SET - MANUAL SPE ED; DOME SET – ZOOM SPEED; DOME SET – ALARM; OSD MEN U SET T I NG

12 B-2. DOME S ET - RECOVER This feat ure allows the dome to work from the last setting before you use the dom e manually (Auto scan, group tour, pattern or sectors) , after the set time, even power shut down and it turns on again. Recovery tim e can be programmed from 15 second to 90 seconds. The d...

Page 15 - the cursor is at SAVE AND EXI T.

15 - To clear memorized data, move joystick to the right direction when cursor is on each item. Press FOCUS NEAR button when the cursor is at YES in order to clear memorized data. Then each item such as tour, preset, sector and so on is displayed on the m onitor about 2~3 seconds. After this proc es...

Page 16 - CAMERA SE T - FLICKERLESS; CAMERA SE T - MIRR OR; CAMERA SE T – APER TURE

16 C. C AMERA SET C-1. CAMERA SE T - FLICKERLESS Flickerless feature is selected between 50Hz and 60H z. The default setting is OFF (NTSC: 60Hz / PAL: 50Hz). S et flicker mod e ON when power source is in discord with frequenc y. The default setting is O FF C-2. CAMERA SE T - MIRR OR This feat ure cr...

Page 18 - PRESET – PRESET ID; PRESET – SAVE; PRESET – EXIT

18 D. PRESET SET To enter PRESET SET, move the joystick to the right direction. D-1. PRESET – PRESET NO. Up to 164 numbers of preset positions are available. Move j oystick to the right or left direction to select a preset no. D-2. PRESET – PRESET ID To set preset ID, select up to 16 characters usin...

Page 24 - Up t o 8 programmable sectors are available with 16 characters.; Start Position

24 J. SECTOR SET Up t o 8 programmable sectors are available with 16 characters. This feature is useful to memorize certain locations such as a parking zone, etc . When a camera goes through this area, it show s the letter you memori zed. J-1. SECTOR SET – SECTOR N O. Up to 8 programmable sectors se...

Page 25 - camera is ready t o operate.; DIP SWITCH SETTING

25 K. EXIT To escape the OSD Main Menu, move the joystick to the right or left direction then this camera is ready t o operate. A-1. D IP SW SETTING This Speed Dome camera provides up to 63 cam era ID ’s, adjustable using the 1 st ~6 th D ip switch. O pen the camera case to set ID using DIP SW 1. * ...

Page 27 - TROUBLE SHOOTING

27 If you have trouble operating in your camera, refer to the following. PROBLEM SOLUTION Not operati ng Check if the pow er supply is 12 VDC. Check if RS -485 communication cable is connect ed correctly.Check camera ID set ting. Check the termination. No picture Check if all the cables are connecte...

Page 28 - MODEL; SPECIFICATIONS

28 MODEL HTSD10X P an Rot at ion Angle 360 ˚ Endless Manu al 10 ˚ ~ 200˚/sec P an Speed Preset Max 200 ˚ /sec Tilt Rot ation Angle 0 ˚ ~ 90˚ Manu al 10 ˚ ~ 200˚/sec Tilt Speed Preset Max 200 ˚ /sec PA N /TILT System Accuracy 0.02 ˚ Preset s 164 positions wit h a 16-char act er label available f or e...

Page 29 - DIMENSIONS

29 NTS C ON / OFF (1/100) Flicker less PAL ON / OFF (1/120) W HI TE BALANCE AW B/ATW /I NDOO R/ OUT DOO R DIMENSIONS