SOYO 6KB82440 - Manual

SOYO 6KB82440

SOYO 6KB82440 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
Page: / 46

Table of Contents:

  • Page 3 – iii; Table of Contents
  • Page 4 – iv
  • Page 5 – Introduction; Key Features; Ñ supports 4 strips of 168-pin EDO /SDRM Unbuffered
  • Page 6 – Unpacking the Mainboard; The mainboard package contains:; Electrostatic Discharge Precautions
  • Page 7 – Mainboard Layout w/ Default Settings; Figure 1Ð1. Mainboard Layout
  • Page 8 – Figure 1Ð2. Mainboard Default Setting
  • Page 9 – Hardware Setup; CAUTION; Turn off power to the mainboard, system chassis, and; Jumpers; JP5: CMOS Clear Jumper; CMOS Setting; Retain CMOS data
  • Page 10 – SW1: Bus Fraction Core/Bus Ratio Select Jumper; Set this jumper according to your CPU clock.; Ratio; CPU Type Configuration; Figure 2Ð1Ð1. CPU Jumper Settings
  • Page 11 – Figure 2Ð1Ð2. CPU Jumper Settings; Figure 2Ð1Ð3. CPU Jumper Settings; Figure 2Ð1Ð4. CPU Jumper Settings; Memory Configuration; The mainboard supports four banks of; Unbuffered DIMM; . The mainboard supports
  • Page 12 – Multi I/O Port Addresses; Port; Note: Some sound cards have a default IRQ setting for IRQ7, which may; Connectors; ATX PW — ATX Power Supply Connectors; PS/2 Keyboard Connector
  • Page 13 – IR – IR Connector; IR Connector; Empty; Keylock & Power LED Connector; Attach the system speaker to connector SPK.; RST – Hardware Reset Control
  • Page 14 – Attach on-board hard disk drives to these connectors.; IDE LED – IDE HDD LED Connectors; Attach floppy cable to this connector.; PRT – Parallel Port Connector; Attach parallel port cable to this connector.; USB1/USB2 – Universal Serial Bus Connector; Attach USB cable to these connectors for external USB device.
  • Page 15 – FAN: CPU Cooling Fan Connector; CPU Cooling Fan; JP44 Pin Assignment
  • Page 16 – Slot 1 Installation Guide
  • Page 21 – Top View of CPU Support Clip
  • Page 22 – BIOS Setup; are asked to press DEL to enter Setup.
  • Page 23 – Standard CMOS Setup; in
  • Page 24 – Video; Note: This function is for a special disk drive; Halt On; Choose halt mode when BIOS detects system
  • Page 25 – BIOS Features Setup; The screen below shows the; External Cache
  • Page 26 – Boot Sequence; Enable this option to adjust the keystroke repeat rate.; Security Option
  • Page 27 – Enabled: The color of the monitor may be incorrect
  • Page 28 – Chipset Features Setup; Change these settings only if you are familiar with the Chipset.; Auto Configuration
  • Page 30 – Use the default setting.; Disabled; Show the current status of CPU.
  • Page 31 – Power Management Setup; User Define
  • Page 32 – Video Off Method
  • Page 33 – PNP/PCI Configuration Setup; Choose ÒPNP/PCI CONFIGURATION SETUPÓ from the Main; Use the arrow keys to move between items and select values. Modify
  • Page 34 – Load Setup Defaults; Note: The SETUP Defaults are optimized for the most stabilized
  • Page 35 – Load BIOS Defaults; Choose this item and the following message appears:; Integrated Peripherals; Run the Integrated Peripherals as follows.; A short description of screen items follows:
  • Page 36 – IDE HDD Block Mode; Enabled: U s e t h e o n - b o a r d f l o p p y; Onboard Serial Port 1; Standard: Use standard UART mode
  • Page 37 – Onboard Parallel Port
  • Page 38 – Supervisor Password; After you enter your password, the following message appears
  • Page 39 – User Password; The following message appears:
  • Page 40 – IDE HDD Auto Detection; Note: This function is only valid for
  • Page 41 – Drivers Installation Guide; Under DOS command line prompt, run the SETUP directly.
  • Page 42 – SCO UNIX
  • Page 43 – custom
  • Page 44 – From root directory, type the following commands:
  • Page 45 – Quick Installation Guide; Motherboard Layout; CPU Jumper Settings; CPU Frequency Settings:
  • Page 46 – Memory Configurations; DIMM BANKS; RAM Type; Connectors and Jumper Settings; PORT
Loading the manual

6KB

82440 LX PCI Mainboard
User’s Guide &
Technical Reference

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - iii; Table of Contents

iii Table of Contents Chapter 1: Introduction .................................................. 1 Key Features ............................................................................... 1 Unpacking the Mainboard ........................................................... 2 Electrostatic Discha...

Page 4 - iv

iv Chapter 3: BIOS Setup .................................................. 19 Standard CMOS Setup .............................................................. 20 BIOS Features Setup ................................................................. 21 Chipset Features Setup ..........................

Page 5 - Introduction; Key Features; Ñ supports 4 strips of 168-pin EDO /SDRM Unbuffered

1 Introduction The 82440 LX PCI mainboard is a high-performance ATX architecturesystem board that supports 686 (PII) family CPUs. This mainboard isfully compatible with industry standards, and adds many technicalenhancements. Key Features ¥ Processor supports:Ñ 686 (PII) CPU up to 66 MHz host bus fr...

Other SOYO Models

All SOYO Other