South Bend SB1012 - Manual

SAFETY For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -5- S A F E T Y Understanding Risks of Machinery Operating all machinery and machining equipment can be dangerous or relatively safe depending on how it is installed and maintained, and the operator's experience, common sense, risk awareness, ...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -7- S A F E T Y Additional Metal Lathe Safety 7. Speed Rates. Operating the lathe at the wrong speed can cause nearby parts to break or the workpiece to come loose, which will result in dangerous projectiles that could cause severe impact injury. Lar...

PREPARATION -8- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes P R E P A R A T I O N Preparation Overview Things You'll Need To complete the preparation process, you will need the following items: For Lifting and Moving s !&ORKLIFTOR/THER0OWER,IFTING$EVICE (rated for at least 5000 lbs). s ,IF...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -9- P R E P A R A T I O N Inventory Main Inventory 1: (Figure 2 ) Qty A. Steady Rest Assembly .................................... 1 B. 12" Faceplate w/D1-6 Camlock Stud Set ...... 1 C. 10" Four-Jaw Chuck w/Combo Jaws ............. 1 D. Four-...

-10- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes P R E P A R A T I O N The unpainted surfaces are coated at the factory with a heavy-duty rust preventative that prevents corrosion during shipment and storage.The benefit of this rust preventative is that it works very well. The downside is that ...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -11- P R E P A R A T I O N Keep Workpiece Loading Area Unobstructed Lathe ElectricalAccessDoor = Power Connection Location B C A D Min. 30" Wall Figure 4. Space required for full range of movement. S B1012-13 S B1014-15 S B103 7 -3 8 A 90" 10...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -13- P R E P A R A T I O N 6. Attach the lifting straps to forklift forks or a hook and chain, as shown in Figures 8–9 . Forklift Forks Lifting Straps 12" Long2x6 Board 12" Long2x6 Board Figure 8. Lathe set up for lifting with forklift. 7. Un...

-14- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes P R E P A R A T I O N Assembly With the exception of the handwheel handles, the lathe is shipped fully assembled. To install the handwheel handles, thread the large handle into the carriage handwheel and the small handle into the cross slide han...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -15- P R E P A R A T I O N In addition to the gearboxes, we also recommend that you lubricate all other points on the machine at this time. This can be accomplished by following the maintenance schedule on Page 54 . Note: If your lathe was shipped wi...

-16- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes P R E P A R A T I O N Connecting Power Cord to Lathe Electrocution or death will occur if you attempt this procedure with the power cord connected to the power source. The cord must be disconnected from power before performing this procedure. Th...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -17- P R E P A R A T I O N Correcting Out-of-Phase Wiring This sub-section is only provided for troubleshooting. If you discover during the test run that the lathe will not operate, or that the spindle runs backwards, the lathe may be wired out of ph...

OPERATION For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -23- O P E R A T I O N Operation Overview Loose hair, clothing, or jewelry could get caught in machinery and cause serious injury or death. Keep these items away from moving parts at all times to reduce this risk. During operation, small me...

-24- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N Refer to the following figures and descriptions to become familiar with the basic controls of this machine. Main Power Switch The main power switch is shown in Figure 33 . It turns master power ON/OFF to the lathe. A. Change Ge...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -25- O P E R A T I O N H. Cutting Fluid Flow Control Lever: Controls the flow of cutting fluid from the nozzle. I. Compound Slide Handwheel: Moves the compound slide forward or backward. Includes an indirect-read graduated scale (distance represents ...

-26- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N Tailstock Controls Foot Brake AA. Quill Handwheel: Moves the quill toward or away from the spindle. AB. Graduated scale: Indicates quill movement in increments of 0.001" or 0.02mm. AC. Tailstock Lock Lever: Secures the tail...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -27- O P E R A T I O N Chuck & Faceplate Mounting This lathe is shipped with the 3-jaw chuck installed. This is a scroll-type chuck, meaning that all three jaws move in unison when adjusted. The included 4-jaw chuck features independent jaws, whi...

-28- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N Mounting Chuck or Faceplate The 4-jaw chuck is shipped with six camlock studs that must be installed before the chuck can be mounted, as explained in this procedure. If you have not yet installed the camlock studs, complete the...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -31- O P E R A T I O N Changing Jaws Item Needed Qty Chuck Key ............................................................. 1White Lithium Grease .......................... As Needed To change the jaw: 1. DISCONNECT LATHE FROM POWER! 2. Place a piec...

-32- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N 4-Jaw Chuck Refer to Chuck & Faceplate Mounting instructions on Page 27 to mount the 4-jaw chuck to the spindle. The 4-jaw chuck features independently adjustable hardened steel jaws to hold non-cylindrical or off-center wo...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -33- O P E R A T I O N Removing Tooling 1. Use a shop rag to hold the tool. 2. Rotate the tailstock quill handwheel counterclockwise until the tool is forced out of the quill. To install tooling in the tailstock: 1. With the tailstock locked in place...

-34- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N Offsetting The tailstock can be offset from the spindle center line for turning tapers. The offset movement is controlled by set screws on both sides of the tailstock (see Figure 57 ), and the amount of movement is indicated by...

-36- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N Faceplate Refer to Chuck & Faceplate Mounting instructions on Page 27 to mount the faceplate to the spindle. The 12" faceplate included with your lathe offers a wide range of uses, including machining non-concentric wor...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -37- O P E R A T I O N Mounting Dead Center in Spindle 1. DISCONNECT LATHE FROM POWER! 2. Thoroughly clean and dry the tapered mating surfaces of the spindle bore, tapered sleeve, and the center, making sure that no lint or oil remains on the tapers....

-38- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N Mounting Center in Tailstock Either a dead center or live center can be mounted in the tailstock. Mounting instructions are the same for both. Figure 67 shows an example of a dead center mounted in a tailstock. Figure 67. Examp...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -39- O P E R A T I O N 5. Close the steady rest so that the workpiece is inside the finger rollers, then tighten the lock knob. 6. Loosen the three wing bolts so the finger roller positions can be adjusted. 7. Use the finger adjustment knobs to just ...

-40- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N 2. Rotate the compound to the desired angle, as indicated by the scale at the base, then retighten the two hex nuts. — If setting up to cut external right-hand inch or metric threads, or left-hand internal threads for the first ...

-42- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N Adjustable Apron Stop System Use the adjustable apron stop collar (shown in Figure 75 ) to set the location where the carriage will be disengaged by the feedrod friction clutch. When the adjustable apron stop contacts the stop ...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -43- O P E R A T I O N Manual Feed You can manually move the cutting tool around the lathe for facing or turning operations using the handwheels shown in Figure 77 and described below. Carriage Handwheel The carriage handwheel moves the carriage left...

-44- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N On this machine, both the carriage and cross slide have power feed capability. The rate that these components move (feed rate) is controlled by how the levers are configured on the gearbox. Feed rate and spindle speed must be co...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -45- O P E R A T I O N Power Feed Controls The feed direction lever ( Figure 81 ) controls direction of the carriage. The quick change feed direction knob ( Figure 82 ) reverses the feed direction of the carriage while the lathe is running. Figure 81...

-46- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N Understanding Thread & Feed Rate Chart Figure 84 shows the configurations of gearbox levers that are required to set the available feed rates. This same chart can also be found on the machine. Figure 84. Thread and feed rat...

-48- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N Note: Take care not to misplace the key from the gear shaft. b. Clean away debris and grime from the gear and apply a light coat of machine oil. c. Swap the position of the gear, as shown in Figure 87 , then align it with the k...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -49- O P E R A T I O N Using Thread Dial and Chart Find the TPI (threads per inch) that you want to cut in the left column (see Figure 92 ), then reference the dial number to the right of it. The dial numbers indicate when to engage the half nut for ...

-50- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes O P E R A T I O N The chip drawer shown in Figure 99 catches swarf and metal chips during the machining process. It easily slides open to provide access to swarf during cleanup. Also, the chip drawer contains a screen that allows runoff cutting ...

ACCESSORIES -52- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes A C C E S S O R I E S Accessories This section includes the most common accessories available for your lathe, which may be available through your local South Bend Lathe Co. dealer. If you do not have a dealer in your area, please cal...

MAINTENANCE -54- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes M A I N T E N A N C E Always disconnect power to the machine before performing maintenance. Failure to do this may result in electrocution or accidental startup injury. ! Maintenance Schedule Each operator of this machine is responsi...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -55- M A I N T E N A N C E Use this chart to keep track of the maintenance performed on your South Bend Lathe. Cross out or initial the “Day” box for each item on the list. If the box is blacked out, maintenance is not required for that item on that ...

-56- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes M A I N T E N A N C E Lubrication Headstock Oil Type .. Mobil DTE Light or ISO 32 EquivalentOil Amount .............................................. 7.5 LitersCheck/Add Frequency .................................... DailyChange Frequency .........

-58- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes M A I N T E N A N C E Figure 113. Location of gearbox fill and drain plugs. Gearbox Oil Fill Plug Gearbox Oil Drain Plug Gearbox Oil Type ...... Mobil Vactra 2 or ISO 68 EquivalentOil Amount ...................................................1 L...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -59- M A I N T E N A N C E Ways & Slides The way pump shown in Figure 117 lubricates the saddle and cross slide way guides with the oil from the apron reservoir. To use the way pump to lubricate the ways, pull the pump knob out for two or three s...

-60- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes M A I N T E N A N C E Ball Oilers Oil Type .. Mobil DTE Light or ISO 32 EquivalentOil Amount ..........................................1 or 2 DropsLubrication Frequency ................................... Daily This lathe has five ball oiler loca...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -61- M A I N T E N A N C E End Gearing Grease Type ............................................... NLGI#2Frequency ................ Annually or When Swapping The end gears, shown in Figure 121 , should always have a thin coat of heavy grease to minim...

-62- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes M A I N T E N A N C E Cutting Fluid System The cutting fluid system consists of a fluid tank, pump, and flexible nozzle. The pump pulls fluid from the tank and sends it to the valve, which controls the flow of cutting fluid to the work area. Whe...

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -63- M A I N T E N A N C E Changing Cutting Fluid When you replace the old cutting fluid, take the time to thoroughly clean out the chip drawer, catch tray, and chip tray. The entire job only takes about a 1 ⁄ 2 hour when you are prepared with the pr...

-64- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes M A I N T E N A N C E Machine Storage If the machine is not properly prepared for storage, it may develop rust or corrosion. If decommissioning this machine, use the steps in this section to ensure that it remains in good condition for later use...

SERVICE For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -65- S E R V I C E Backlash Adjustment Figure 126. Cross slide backlash adjustment screws. Cap Screw Set Screw Cross Slide Leadscrew Tools Needed: Qty Hex Wrench 3mm ................................................. 1Hex Wrench 5mm .............

-66- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes S E R V I C E After a long period of time, you may find that the leadscrew develops a small amount of end play. This lathe is designed so that leadscrew end play can be easily removed with adjustment. Tools Needed: Qty Open End Wrench 1" ......

For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes -67- S E R V I C E Half Nut Adjustment The half nut mechanism can be tightened if it becomes loose from wear. The pressure exerted by the half nut is controlled by a gib similar to the one in the saddle, which is on Page 66 . The half nut gib is adju...

TROUBLESHOOTING -74- For Machines Mfg. Since 7/ 09 EVS Toolroom Lathes T R O U B L E S H O O T I N G If you need replacement parts, or if you are unsure how to do any of the solutions given here, feel free to call us at (360) 734-1540. Symptom Possible Cause Possible Solution Machine does not start ...

WARRANTY & RETURNS W A R R A N T Y This quality product is warranted by South Bend Lathe Company to the original buyer for one year from the date of purchase. This warranty does not apply to consumable parts, or defects due to any kind of misuse, abuse, negligence, accidents, repairs, alteration...

Hundreds of Thousands of Lathes Sold With a Tradition of Q uality Since 1906! © March, 2010 by South Bend Lathe Co. For Machines Mfg. Since 7/09 16" X 60" EVS TOOLROOM LATHES MODEL SB1014 - 220V MODEL SB1015 - 440V SPECIFICATIONS

Hundreds of Thousands of Lathes Sold With a Tradition of Q uality Since 1906! © November, 2009 by South Bend Lathe Co. For Machines Mfg. Since 7/09 14" & 16" EVS TOOLROOM LATHES MODELS SB1012/SB1014/SB1037 - 220V MODELS SB1013/SB1015/SB1038 - 440V WIRING MANUAL

ELECTRICAL For Machines Mfg. Since 8 / 09 EVS Toolroom Lathes -1- E L E C T R I C A L Electrical Safety Instructions These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines. Study this section care...

-2- For Machines Mfg. Since 8 / 09 EVS Toolroom Lathes E L E C T R I C A L Wiring Overview 220 VAC 3-PH 6 = : > ? 8 7 < A B @ ; 9 Spindle Motor,Page 9. CoolantPump Motor, Page 11. Oil PumpMotor,Page 10. Oil PressureSwitch, Page 10. Door LimitSwitch, Page 14. Brake Limit Switch, Page 14. Spindl...

For Machines Mfg. Since 8 / 09 EVS Toolroom Lathes -3- E L E C T R I C A L : 8 8 @ ; A = ? B CoolantPump Motor, Page 11. Oil PumpMotor,Page 10. Oil PressureSensor, Page 10. Brake Limit Switch, Page 14. Chuck Guard Limit Switch, Page 14. Electrical Box, Pages 6 & 7. Cooling Fan, Page 6. Main Powe...

-4- For Machines Mfg. Since 8 / 09 EVS Toolroom Lathes E L E C T R I C A L X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X L1 L4 L3 L2 X X X C IR C U IT B O AR D KR1 24V 0V KR4 COM KR4 N O KR4 N C 0V KR4 KR3 KR2 NO 24V CO M BR AKE NC NO NO SROT A T ION COM CHUCK NC COM JOG CSS 3 2 1 S2...

-6- For Machines Mfg. Since 8 / 09 EVS Toolroom Lathes E L E C T R I C A L Fig. 2. Electrical box. Electrical Box box photo

-8- For Machines Mfg. Since 8 / 09 EVS Toolroom Lathes E L E C T R I C A L 220V Oil Pump Motor & Pressure Sensor 440V Oil Pump Motor & Pressure Sensor Figure. 5. Oil pump motor & pressure sensor location. Figure. 6. Oil pump motor & pressure sensor location. Oil Pump Motor Oil Pump M...

For Machines Mfg. Since 8 / 09 EVS Toolroom Lathes -9- E L E C T R I C A L Ground COOLANT PUMP MOTOR (220V) 3 2 1 4 6 5 W1 W1 V1 V1 U1 Ground COOLANT PUMP MOTOR (440V) Ground 3 2 1 4 6 5 W1 W1 V1 V1 U1 220V Coolant Pump Wiring 440V Coolant Pump Wiring Figure. 7. Coolant pump location. Figure. 8. Coo...

-10- For Machines Mfg. Since 8 / 09 EVS Toolroom Lathes E L E C T R I C A L Control Panel Wiring control panel and coolant mo-tor Fig. 9. Control panel location. Control Panel 220V GND IN +12V 110V 0V Bk X X 13 X 14 COM L K L11 1 3 3 TACHOMETER DISPLAY SPINDLE SPEED DIAL COOLANT PUMP SWITCH JOG BUTT...

For Machines Mfg. Since 8 / 09 EVS Toolroom Lathes -11- E L E C T R I C A L Spindle Rotation Switch 220V Power Connection 440V Power Connection Fig. 10. Spindle rotation switch location. NC COM NC COM NO NO 7 8 6 9 Spindle Rotation Switch, Figure 10. spindle rotation and power conn-tection Ground Ho...

-12- For Machines Mfg. Since 8 / 09 EVS Toolroom Lathes E L E C T R I C A L Fig. 11. RPM sensor and door limit switch location. Fig. 12. Brake limit switch location. Fig. 13. Chuck guard limit switch. COMMON NC NO Bk Wt X K COM L A1 3 X 1 0 Bk Wt 0 2 13 14 21 22 NC NC NO NO 3 4 X 5 A1 X 9 Door Limit...

Hundreds of Thousands of Lathes Sold With a Tradition of Q uality Since 1906! © November, 2009 by South Bend Lathe Co., Revised June, 2010 (TS) For Machines Mfg. Since 7/09 16" X 60" EVS TOOLROOM LATHES MODEL SB1014 - 220V MODEL SB1015 - 440V PARTS MANUAL

Customer Service We stand behind our machines. If you have any service questions, parts requests or general questions about the machine, feel free to contact us. South Bend Lathe Co. P.O. Box 2027 Bellingham, WA 98227 Phone: (360) 734-1540 Parts Department: (417) 886-2954 Fax: (360) 676-1075 (Intern...

-2- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Headstock Casing 1 2 3 4 6 7 8 9 10 11 12 13 5 9-1 REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PSB10120001 OIL FILL PLUG 8 PFH30M FLAT HD SCR M5-.8 X 8 2 PCAP29M CAP SCREW M6-1 X 40 9 PSB10120009 OIL DISTRIBUTOR A-5S 3 PSB10120...

-4- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Headstock Controls Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 14 PSS30M SET SCREW M10-1.5 X 10 33 PSB10120033 HANDLE WASHER 6MM 15 PSB10120015 THREADED PLUG M10-1.5 34 PCAP01M CAP SCREW M6-1 X 16 16 PSB10120016 COMPRE...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -5- P A R T S Headstock Upper Gearing 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 60 58 34 65 57 66 34 86 96 96 34

-6- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Headstock Upper Gearing Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 34 PCAP01M CAP SCREW M6-1 X 16 78 PSB10120078 SPINDLE PULLEY 55 PSB10120055 INBOARD DRIVE SHAFT END CAP 79 PSB10120079 PULLEY WASHER 8MM 56 PORG050 O-...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -7- P A R T S Headstock Transfer Gearing 34 66 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 34 34 112 110 109 105 34 34 112 115 110 115 121 REF PART # DESCRIPTION REF PART # DESCRIPTION 34 PCAP0...

-8- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Gearbox Gearing 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -9- P A R T S Gearbox Gearing Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 201 PSB10120201 SPLINE SHAFT 232 PSB10120232 GEAR 19T 202 PSB10120202 OIL SEAL 20 X 32 X 5 233 PSB10120233 GEAR 20T 203 PSB10120203 SLEEVE BEARING TAF202820 2...

-10- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Gearbox Controls 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 3...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -11- P A R T S Gearbox Controls Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 262 PSB10120262 GEARBOX COVER GASKET 301 PSB10120289 WOODRUFF KEY 4 X 13 263 PSB10120263 PARTITION NUT 302 PSB10120302 SHIFT SHAFT 264 PSB10120264 UPPER PLA...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -13- P A R T S Apron - Front View Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 501 PSB10120501 DOUBLE GEAR 18T/60T 529 PORP026 O-RING 25.7 X 3.5 P26 502 PSB10120502 GEAR SPACER 530 PSB10120530 FEED DIRECTION SHAFT SLEEVE 503 PRP20M R...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -15- P A R T S Apron - Rear View Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 514 PSTB001 STEEL BALL 1/4 569 PSB10120569 HALF-NUT LEVER HUB 522 PSB10120522 GEAR 18T 570 PSB10120046 COMPRESSION SPRING 6 X 27 534 PORP012 O-RING 11.8 X ...

-16- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Dial Indicator 701 702 703 704 705 707 708 751 753 754 REF PART # DESCRIPTION 701 PSB10120701 DIAL INDICATOR INDEX PLATE 702 PSB10120702 PIVOT SHAFT 703 PSB10120703 DIAL INDICATOR CASTING 704 PSB10120704 KNURLED KNOB 705 PSB101207...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -17- P A R T S Compound Slide & Tool Post REF PART # DESCRIPTION REF PART # DESCRIPTION 901 PSB10120901 TOOL POST HANDLE 918 PSB10120918 LEADSCREW SUPPORT BRACKET 902 PSB10120902 TURRET NUT 919 PSB10120919 DUAL INDEX RING 903 PSB10120903 TUR...

-18- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Saddle Body & Controls 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1013A 1014 1015 1016 1017 1018 1019 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1051 1101 1102 1103 11...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -19- P A R T S Saddle Body & Controls Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1001 PSB10121001 CROSS GIB ADJUSTMENT SCREW 1031 PSB10121031 BEARING CAP 18 X 52 X 4 1002 PSB10121002 CROSS SLIDE 1032 PSB10121032 INDEX DIAL HOUS...

-20- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Saddle Base REF PART # DESCRIPTION REF PART # DESCRIPTION 1041 PSB10121041 GEAR WASHER 5MM 1050 PSB10121050 STRAIGHT PIPE ADAPTER 1/8 PT X 6MM 1042 PSB10121042 GEAR 16T 1051 PSB10121051 SADDLE OIL PUMP ASSEMBLY 1043 PSB10121043 GE...

-22- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Bed & Shafts Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1201 PSB10141201 BED CASTING 1235 PSB10121235 SHEAR PIN WASHER 1202 PSB10121202 BED END STOP BOLT 1236 PSB10121236 SHEAR PIN COLLAR 1203 PSB10121203 SHAFT E...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -23- P A R T S End Gears REF PART # DESCRIPTION REF PART # DESCRIPTION 1401 PCAP02M CAP SCREW M6-1 X 20 1411 PSB10121411 BEARING SPACER 1402 PSB10121402 GEAR WASHER 6MM 1412 PSB10121412 GEAR SHAFT BUSHING 1403 PSB10141403 GEAR 24T 1413 PSB101214...

-24- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Motor Assembly 1501 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514 1515 1516 1517 1518 1519 1519-1 1519-2 1519-3 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1502 1502 1502...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -25- P A R T S Motor Assembly Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1501 PSB10121501 SIDE COVER MOUNTING PIN 1519-3 PSB10141519-3 MOTOR JUNCTION BOX 1502 PN02M HEX NUT M10-1.5 1520 PSB10121520 SIDE COVER MOUNTING STUD 1503 PW0...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -27- P A R T S Cabinets & Panels Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1601 PSB10141601 CHIP TRAY 1629 PSB10121629 CHUCK GUARD ROD 1602 PSB10121602 BRAKE CAM 1630 PSB10121630 CHUCK GUARD 1603 PCAP01M CAP SCREW M6-1 X 16 16...

-28- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Headstock Oiling System A B C D E A B C D E 1701 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725-3 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -29- P A R T S Headstock Oiling System Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1701 PSB10121701 ELBOW CONNECTOR 1723 PSB10121723 PIPE CONNECTOR 1/4 PT X 1/4 PT 1704 PCAP50M CAP SCREW M5-.8 X 10 1724 PSB10121724 LUBRICATION PUMP ...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -31- P A R T S Tailstock Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1801 PSB10121801 INCH TAILSTOCK LEADSCREW 1828 PSB10121828 TAILSTOCK ALIGNMENT PIN 1802 PSB10121802 INCH LEADSCREW NUT 1829 PSB10121829 PIVOT BLOCK 1803 PK34M KEY ...

-32- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Steady Rest 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2012A REF PART # DESCRIPTION 2001 PSB10122001 FINGER ADJUSTMENT KNOB 2002 PRP51M ROLL PIN 4 X 40 2003 PSB10122003 FINGER CO...

For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts -33- P A R T S Electrical Cabinet & Control Panel 2201 2202 2203 2204 2205 2206 2208 2209 2210 2211 2212 2213 2214 2215 2217 2218 2219 2220 2221 2222 2223 2224 2225 2226 Electrical Cabinet Control Panel 2207 2212

-34- For Machines Mfg. Since 8/09 Model SB1014/SB1015 Parts P A R T S Electrical Cabinet & Control Panel Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 2201 PSB10142201 RESISTOR 800W 20-OHM (SB1014) 2212 PSB10122212 WIRE LOOM 17" 2201 PSB10152201 RESISTOR 600W 100-OHM (SB1015) 2213...