SOUNDSTREAM X3.71 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Table of Contents:
Page 3 – TABLE OF CONTENTS; ABLE OF CONTENTS
Page 4 – INTRODUCTION; this Owners Manual before beginning installation.; INT
Page 5 – FEATURES; FE
Page 6 – CONT
Page 7 – CONTR
Page 9 – Input Sensitivity Adjustment
Page 13 – Speaker Terminals
Page 14 – Planning and Mounting Your System; PLANNING & MOUNTING Y
Page 15 – Wiring Diagram
Page 16 – Bridging Two Amplifiers
Page 17 – BRIDGING TW
Page 19 – Trouble Shooting; SYMPTOMS; OUBLE SHOO
Loading the manual
X3.60 / X3.71
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 3 - TABLE OF CONTENTS; ABLE OF CONTENTS
TABLE OF CONTENTS T ABLE OF CONTENTS ADJUSTING & TUNING 14 BRIDGING TWO AMPLIFIERS 13 PLANNING & MOUNTING YOUR SYSTEM 11 WIRING DIAGRAM 12 CONTROLS & FUNCTIONS FEATURES & SPECIFICATIONS INTRODUCTION 2 5 ~ 10 3 ~ 4 TROUBLE SHOOTING 15
Page 4 - INTRODUCTION; this Owners Manual before beginning installation.; INT
INTRODUCTION Amplifier's provide high-performance sound reinforcement for your mobile audio equipment. The Multi-Mode bridging capabilities allow flexibility in hosting several different speaker configurations. To achieve optimum performance, it is highly recommended that you read this Owners Manual...
FEATURES a source voltage of 13.5V DC 6500Watts350<@80Hz(+/- 5Hz)15Hz ~150Hz0.5 ~ 10.0 (volts)24dB / octave18dB50Hz ~ 150Hz0 ~ 180 deg.0 ~ 18dB11 ~ 16V DC510 amperes DC *23.75" x 11.5" x 2.5"13.5V DC & 14.4V DC Max PowerDamping factorOperating frequency(band-width)Input Sensitivit...
Controls & Functions 1.Low Level OUT RCA jacks 2. Low Level Input RCA jacks The LINE OUT allows you to build multiple amplifier systems without having to use splittercords to distribute the signal. Now it is simply a m atter of bringing one set of RCAS into the first amplifier, then using the li...
Page 13 - Speaker Terminals
Controls & Functions 12.B-Terminal (Chassis ground) 13. Remote Power On To avoid unwanted ignition noise caused by ground loops, it is essential that the Amplifier be grounded to a clean, bare, metal surface of the vehicles chassis. Note : GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT (1 MET...
Page 14 - Planning and Mounting Your System; PLANNING & MOUNTING Y
Planning and Mounting Your System The mounting position of your Amplifier will have a great effect on its ability to dissipate the heat generated during normal operation.Under normal conditions, the heatsink will dissipate sufficient heat to avoid thermal shutdown. However please do not install the ...
Page 15 - Wiring Diagram
WIRING DIA GRAM Wiring Diagram X3.60 X3.71 SUB WOOFER 1 OHM 13 SUB WOOFER 1 OHM
Page 16 - Bridging Two Amplifiers
BRIDGING T W O AMPLIFIERS X3.60 Bridging Two Amplifiers MASTER SLAVE MASTER AMP SL AVE AMP MASTER AMP SL AVE AMP MASTER SLAVE 14 SPEAKER IMPEDANCE 2 OHMS
Page 17 - BRIDGING TW
X3.71 Bridging Two Amplifiers MASTER SLAVE M A S T E R A M P S L AV E A M P SPEAKER IMPEDANCE 2 OHMS M A S T E R A M P S L AV E A M P MASTER SLAVE BRIDGING TW O AMPLIFIERS 15
Page 19 - Trouble Shooting; SYMPTOMS; OUBLE SHOO
Trouble Shooting SYMPTOMS NO SOUND AMP NOTSWITCHING ON NO SOUNDIN ONE CHANNEL AMP TURNINGOFFMEDIUM / HIGHVOLUME PROTECTIONLAMP ON Is the power Is the Diagnostic LED illuminated? (YES) No power to power wire Repair power wire or connections. No power to remote wire with receiver on Check connections ...