SOUNDSTREAM RUB1.2500D - Manuals

Page 2 - RUBICON

CONGRATULATIONS! You now own a Limited Edition RUBICON Amplifier, the product of an uncompromisingdesign and engineering philosophy. To maximize the performance of your system, we recommend that you thoroughly acquaintyourself with its capabilities and features. Please retain this manual and you sal...

Page 3 - FEATURES; Signal to Noise Ratio: 105dB

FEATURES Total Harmonic Distortion:0.5% Frequency Response: 15-150Hz Signal to Noise Ratio: 105dB Damping Factor: >250 Input Sensitivity 100mV - 8V 50-150Hz,12dB Low Pass Fiter 45Hz, 0-18dB Bass Boost 10-40Hz, 12dB Subsonic Filter 180° Phase Switch Midnight Blue Finish w/ Brushed Accents Remote G...

Page 4 - SPECIFICATIONS; DIMENSIONS; MODEL

SPECIFICATIONS Frequency Response 15Hz-150Hz LPF Signal/Noise Ratio Input Voltage Range >105dB THD 50Hz -150Hz,12dB 11-16 Volts DC 30K Ohms High Impedance RCA/LINE Level Input Impedance POWER RATINGS & FUSE MODEL 4 ohm 2 ohm 1 ohm FUSE RUB1.1000DRUB1.1600DRUB1.2500D 600W 700W 1000W 800W 1100W...

Page 5 - TOOLS/PARTS FOR INSTALLATION; NOTE: TOOLS ARE NOT SUPPLIED; Protection Circuitry

TOOLS/PARTS FOR INSTALLATION NOTE: TOOLS ARE NOT SUPPLIED Small flat blade screwdriver phillips screwdriver (#2 or medium sized), Wire cutters, Wire strippers, - #6 round head screws, and 1 - #8 sheet metal screw (or nut, bolt flat washer, start washer) (see detail) 2 Ring connectors (large enough t...

Page 6 - Electrical Wiring; Remote Subwoofer Level Control; RUBICON Amplifiers; Fuses; Mounting the Amplifier; Note

Electrical Wiring All RUBICON Amplifiers are equipped with easy top access screw terminals . These terminals are nickel-plated in order to ensure excellent electrical contact and to resist corrosion. When making electrical connections to the amplifier, please observe the following : Use at least 4 g...

Page 7 - PANEL LAYOUT

PANEL LAYOUT RUB1.1000D RUB1.1600D L R R L Line Out Line Input Input Level Subsonic Filter Bass Boost PHASE 0 180 Low Pass Filter Input Sensitivity Bridged Mode DATALINK PROTECTION REMOTE CONTROL Master Slave .1V-2V 2V-8V Min Max 10Hz 40Hz 50Hz 150Hz 0 +18dB L R R L Line Out Line Input Input Level S...

Page 8 - Class D Monoblock Amplifier Installation Wiring; Low Level Inputs

PANEL LAYOUT RUB1.2500D Class D Monoblock Amplifier Installation Wiring RUB1.1000D/RUB1.1600D/RUB1.2500D R min max Power L R R L Line Out Line Input Input Level Subsonic Filter Bass Boost PHASE 0 180 Low Pass Filter Input Sensitivity Bridged Mode DATALINK PROTECTION REMOTE CONTROL Master Slave .1V-2...

Page 9 - has four fuses

Class D Monoblock Amplifier Installation Wiring RUB1.1000D/RUB1.1600D RUB1.1600D has four fuses here RUB1.1600D has four fuses here FUSES POWER CONNECTIONS BATT+ REMOTE GND SPEAKER FUSES POWER CONNECTIONS BATT+ REMOTE GND SPEAKER 9

Page 13 - Bridging Two RUB1.2500D Amplifiers

POWER CONNECTIONS SPEAKER Bridging Two RUB1.2500D Amplifiers POWER CONNECTIONS SPEAKER 13

Page 14 - TROUBLE SHOOTING; YES; STILL NO SOUND; RPOTECTION CIRCUIT; Short Circuit Protection engaged:

TROUBLE SHOOTING NO SOUND Is the LED lit? YES NO Check Power and Remote turn-on wire for voltage. Make sure Ground wire is secure. STILL NO SOUND See your Authorize Sound Stream Dealer. SOUND IN ONE CHANNEL ONLY Reverse left and right speakers by unplugging the speaker connector. turning it over and...