SOUNDSTREAM EXC.4 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
1
2
3
4
5
6
7
8
9
10
11
12
Table of Contents:
Page 2 – Component Speaker System; Connectors
Page 3 – and; EXC Soft Dome Neodymium Tweeter
Page 4 – Try to mount the components on the same plane.; Flush Mounting; ) Secure the cup in the mounting
Page 5 – FIGURE
Page 6 – FIGURE 6
Page 7 – FIGURE 7
Page 8 – WIRING; EXC System Wiring Diagram
Page 9 – NOTES ON; about; Figure 9
Page 11 – SPECIFICATIONS; EXC System Specifications
Loading the manual
Component Speaker System
OWNER'S MANUAL
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 - Component Speaker System; Connectors
1 Component Speaker System INTRODUCTION AND REGISTRATION Congratulations on your purchase of the Soundstream EXC Component SpeakerSystem. You now own one of the finest car audio speaker systems available. As with all high quality car audio components, professional installation is recommended.Your de...
Page 3 - and; EXC Soft Dome Neodymium Tweeter
2 The EXC Component Speaker System is the result of highly focused engineering effort. Each element of the EXC system represents several advances in automotive speaker technology. When the EXC project was initiated, the following goals were established: • High performance sound reproduction in the a...
Page 4 - Try to mount the components on the same plane.; Flush Mounting; ) Secure the cup in the mounting
LOCATION AND MOUNTING 3 The first step in a successful installation is thorough planning. Choose the location for your speaker components carefully. Follow these suggestions to ensure proper imagingand the best performance: • Select a location where each tweeter and midrange/woofer can be mounted cl...
Page 5 - FIGURE
TWEETER SURFACE MOUNTING 4 1) Remove the tweeter's plastic backplate by separating the plate from the tweeter housing with your two thumbnails at one of the terminal locations, gently prying the two pieces until they snap apart. See Figure 3. 2) Mark the location in which you are going to mount the ...
Page 6 - FIGURE 6
INSTALLING THE EXC MIDRANGE- WOOFER 5 The EXC Midrange/Woofer can be mounted on the front or rear of a panel; gaskets are providedfor both options. The bolt-hole configuration will fit a variety of standard OEM patterns making itideal for direct replacement. Best performance is achieved when the spe...
Page 7 - FIGURE 7
MOUNTING THE EXC CROSSOVER 6 The EXC Passive Crossover can be mounted in virtually any location inside the vehicle. Be sure not to mount the EXC system crossover outside the vehicle, or in a locationwhere it may be exposed to dirt or moisture (e.g., the engine compartment, inside awheel housing, ins...
Page 8 - WIRING; EXC System Wiring Diagram
WIRING 7 EXC System Wiring Diagram Figure 8 shows a diagram illustrating the wiring of the EXC Component SpeakerSystem. It is important to make sure that all connections are in phase; that is positive (+) is connected to positive (+), and negative (-) is connected to negative (-), since an out-of-ph...
Page 9 - NOTES ON; about; Figure 9
8 NOTES ON BI-AMPING Bi-Wiring The EXC component system includes theEXC passive crossover which is optimizedfor the speakers. The EXC crossoverallows for dual amp inputs. See Figure 9. This feature allows for a 4 channelamplifier or two 2 channel amplifiers topower the four individual drivers of an ...
Page 11 - SPECIFICATIONS; EXC System Specifications
SPECIFICATIONS EXC System Specifications Frequency Response 70 Hz - 20,000 Hz +/-3dB 60 Hz - 20,000 Hz +/-3dB 50 Hz - 20,000 Hz +/-3dB Sensitivity 90 dB SPL at 1 meter (2.83v) 96 dB SPL at .5 meter (2.83v) 91 dB SPL at 1 meter (2.83v) 97 dB SPL at .5 meter (2.83v) 92 dB SPL at 1 meter (2.83v) 98 dB ...