Snapper SP400 - Manual

5 SECTION 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operator’s of theSNAPPER PRO HYDRO W ALK BEHIND MOW ER. It’spurpose, aside from recommending standard operatingprocedures and routine service requirements, is topromote SAFETY through the use of accepted ...

6 SECTION 2 - CONTROLS Before operating, become familiar with all thecontrols (See Figure 2.1A) and how to use them.Know beforehand how to STOP the Right Handand Left Hand Traction Wheel Drives, the MowerBlades, and the Engine in preparation for apossible emergency. 2.1 ENGINE CONTROLS - A. Engine S...

7 SECTION 3 - OPERATING INSTRUCTIONS 3.1 PRE-START CHECKLIST Make the following checks and perform the services asrequired before each start-up. IMPORTANT: Before starting your SNAPPER ProHydro machine, the hydraulic reservoir and engineMUST be filled to the proper level with oil. 3.1.1. HYDRAULIC O...

8 SECTION 3 - OPERATING INSTRUCTIONS 3.2 STOPPING IMPORTANT: Pulling backward on both Traction Controls back past Neutral position will cause the machine to backup. 1. Pull back on both Traction Controls simultaneouslytowards handle bar. Manually engage the NeutralLatch Lever. See Figure 3.2. FIGURE...

9 SECTION 3 - OPERATING INSTRUCTIONS WARNING The SNAPPER Pro Hydro Mowers have a Transport Speed, which allows the machine to travel forward at a speed of 6 MPH - it is NOT to be used while walking! Use the Transport Speed ONLY when the machine is equipped with a Riding Sulky! DO NOT make sharp turn...

10 SECTION 3 - OPERATING INSTRUCTIONS 3.5 MOWER OPERATION (Continued from Previous Page) 5. W hile holding both Traction Controls in the neutral position, release Neutral Latch Lever by pulling controls slightly backwards. 6. Simultaneously (and slowly), release both Traction Controls. Machine will ...

12 SECTION 3 - OPERATING INSTRUCTIONS 3.8 CUTTING HEIGHT ADJUSTMENT (Fixed Decks) The Mower has three methods of adjusting cuttingheight listed as follows: 1. Moving position of BLADE on cutter spindle shaft. 2. Moving position of CASTER W HEEL on support. 3. Moving position of MOW ER DECK on power ...

13 SECTION 3 - OPERATING INSTRUCTIONS 3.11 ADJUSTING FIXED DECK ATTACHMENT The Mower Deck has four different positions forattaching it to the power unit. The lowest settingprovides a cutting height range from 1 1/2” to 2 1/2”, themiddle low cut from 2 1/4” to 3 1/4”, the middle high cutfrom 3” to 4”...

14 SECTION 4 - ENGINE TROUBLESHOOTING SYMPTOM PROBLEM SOLUTION PAGE Engine Key OFF. Turn Key to Run. 8 does not Fuel Tank empty. Fill Fuel Tank. 7 start.. Fuel Shut-Off Closed. Open Fuel Shut-Off. 8 Engine Throttle Control not at FAST Put Engine Throttle Control to FAST (Rabbit) (Rabbit) position. p...

16 SECTION 4 - SERVICE & LUBRICATION INFORMATION FIGURE 4.1 TRACTION CONTROL LEVERS Lubricate each with 1-2 shots ofgrease every 25 hours of operation. INTERLOCKSWITCHES Inspect switches for easeof operation. HYDRAULIC OIL Use SAE 10W-30 Oil. HYDRAULIC FILTER Change Hydraulic Oil and Filterafter...

17 SECTION 4 - SERVICE & LUBRICATION INFORMATION HOURS PROCEDURE COMMENTS BREAK-IN Check all fasteners for proper tightnessChange Engine Oil and Filter at 5 hours .............................. See engine manualChange Hydraulic Oil and Filter at 25 hours ........................ Use SAE 10W -30....

18 SECTION 4 - SERVICE WARNING Once blades are disengaged, they should come to acomplete stop in 7 seconds or less. If the bladescontinue to rotate after 7 seconds, the electricclutch must be checked. Replacement of electricclutch may be necessary. Return machine to dealerfor replacement. DO NOT CON...

18 SECTION 4 - SERVICE 4.2.3. HYDRAULIC PUMP BELT REMOVAL (Continued)2. Loosen Nut on Belt Guide at rear of Engine Pulley and remove Cutter Deck Belt from Engine Pulley. 3. Remove Hydraulic Pump Belt. 4.2.4. HYDRAULIC PUMP BELT INSTALLATION1. STOP ENGINE! Place Hydraulic Belt on Engine andPump Pulle...

20 SECTION 5 - MOWER ATTACHMENT SERVICE 5.1 CUTTER DECK BELT REMOVAL & INSTALLATION 5.1.1. 36” CUTTING DECK BELT REMOVAL 1. Move Mower onto a smooth, level surface. Turn Ignition Key to STOP position, remove Key,disconnect Spark Plug W ire and secure W ire awayfrom Spark Plug. 2. Remove Mower de...

21 SECTION 5 - MOWER ATTACHMENT SERVICE 5.1.5. SPINDLE TO SPINDLE DECK BELT INSTALLATION - 48”, 52”, & 61” CUTTING DECKS 1. Route new belt for 48” cutting deck, 52” cutting deck,and 61” cutting decks, onto bottom groove of centerSpindle Pulley and left hand Spindle Pulley. SeeFigure 5.3. 2. Inst...

23 SECTION 6 - BATTERY SERVICE & TESTING WARNING Shield the positive terminal with terminal coverlocated on battery harness. This prevents metal fromtouching the positive terminal, which could causesparks. Cables must be connected to battery terminals in the proper position. RED (Positive) cable...

24 SECTION 6 - BATTERY SERVICE & TESTING 6.5 NEW BATTERY PREPARATION 1. Remove battery from carton. 2. Place battery in a well ventilated area on a level non-concrete surface. 3. Remove battery cell caps. Fill cells as required withelectrolyte (purchased separately) to proper level. Fillto 3/16”...

25 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be def...

30 SERVICE NOTES ___________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________...

32 Safety Instructions & Operator’s Manual for PRO HYDRO MID-SIZE WALKBEHIND MOWERS SERIES 1 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on thedate manufactured. The labels on those engines contain very important emissions informat...