Snapper SPE1250KW, SPE140KW, SPE150KH, SPE360, SPE480 - Manual

5 SECTION 1 - FAMILIARIZATION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER PRO GEAR WALK BEHIND MOWER. Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted ...

6 SECTION 2 - SAFETY MESSAGES AND DECALS REVERSE NEUTRAL TRANSMISSION SHIFT LEVER POSITIONS LOWEST SPEED HIGHEST SPEED CHOKE SYMBOL RABBIT “FAST” SPEED TURTLE “SLOW” SPEED KEYSWITCH POSITIONS ENGINE “OFF” ENGINE “RUN”

7 SECTION 2 - CONTROLS FIGURE 2.1 BLADE CLUTCH SWITCH KEY SWITCH OPERATOR’S PRESENCE CONTROL (OPC) RIGHT HAND TRACTION LEVER TRACTION LOCK LEVER TRANSMISSION SHIFT LEVER ENGINE SPEED CONTROL

8 SECTION 3 - OPERATING INSTRUCTIONS 3.1 BEFORE OPERATING Be Thoroughly familiar with all controls and how to use them before operating the machine. Know beforehand how to STOP the Traction W heel Drives, Mower Blades and Engine in preparation for possible emergencies. 3.2 EMERGENCY STOP - PISTOL GR...

12 SECTION 3 - OPERATING INSTRUCTIONS WARNING Brakes require maintenance. Inspect for proper operation before operating machine. Refer to Section “ADJUSTMENTS, STEERING AND BRAKES”. 3.7 TRACTION LOCK OPERATION - PISTOL GRIP 1. Simultaneously squeeze both Traction Levers toward the handle, to stop mo...

13 SECTION 3 - OPERATING INSTRUCTIONS 3.10 CUTTING HEIGHT ADJUSTMENT (Fixed Decks) Mower has three methods of adjusting cutting height: 1. Moving position of BLADE on cutter spindle shaft. 2. Moving position of CASTER W HEEL on support. 3. Moving position of MOW ER DECK on power unit. WARNING DO NOT...

14 SECTION 3 - OPERATING INSTRUCTIONS 3.12.1 ADJUSTING BLADE ON CUTTER SPINDLE (Continued) FIGURE 3.15 3.13 ADJUSTING FIXED DECK ATTACHMENT The mower deck has four different positions for attaching it to the power unit. The lowest setting provides a cutting height range of 1-1/2” to 2-1/2”, the midd...

15 SECTION 4 - TROUBLESHOOTING ENGINE TROUBLESHOOTING SYMPTOM PROBLEM SOLUTION Engine ................... Key OFF. ...............................................................................................Turn Key to Run. does not ................ Fuel Tank empty. .................................

16 SECTION 4 - TROUBLESHOOTING MOWER TROUBLESHOOTING (Continued) SYMPTOM PROBLEM SOLUTION Mower not ...................................... Broken or slipping Blade Belt. ......................................Replace Belt. cutting full ...................................... Dull, Damaged or W orn Bla...

17 SECTION 5 - ADJUSTMENTS 5.1 STEERING/BRAKES If machine is not as responsive as desired when either Traction lever is squeezed, one or both brakes should be adjusted as follows: 1. Operate mower on level terrain with Transmission Shift Lever in No. 1 position. Determine which brake requires adjust...

18 SECTION 5 - ADJUSTMENTS 5.3 HANDLE HEIGHT The operator handle can be adjusted for operator comfort as follows: 1. Loosen the upper carriage bolt and nut on both sides of handlebar. 2. Remove lower carriage bolt and nut on both sides of handlebar. 3. Raise or lower handlebar to desired height. See...

19 SECTION 6 - POWER UNIT SERVICE 6.1 REPLACEMENT PARTS To retain the quality of your mower, use Genuine SNAPPER Replacement Parts only! Contact your local SNAPPER dealer for parts and service assistance. For the correct part or information for your mower, always mention Model and Serial Number of P...

20 SECTION 7 - MOWER ATTACHMENT SERVICE 7.1 TRANSMISSION BELT REMOVAL/REPLACEMENT Should it become necessary to replace the transmission drive belt, contact an authorized SNAPPER Dealer for service. WARNING DO NOT attempt any maintenance, adjustments or service with the engine running. Stop engine. ...

21 SECTION 7 - MOWER ATTACHMENT SERVICE 7.4 CUTTING BLADE SERVICE Check blades after each use for signs of excessive wear and damage. See Figure 7.4 for blade wear limits. FIGURE 7.4 1. Use the following chart for ordering replacement Blades for the 36” & 48” Mowing Decks. STANDARD REPLACEMENT B...

23 ELECTRICAL FIGURE 7.9 KEY WITH COVER KEYSWITCH BLADE CLUTCH SWITCH OPC SWITCH (PISTOL GRIP MODELS ONLY) CONNECTOR NOTCH 15 AMP FUSE TO TRANSMISSION SWITCH MAIN WIRE HARNESS OPC SWITCH (PISTOL GRIP MODELS) KAWASAKI ENGINE ONLY KAWASAKI MODULE KAWASAKI PIGTAIL KAWASAKI CAPACITOR TO MAIN HARNESS GRO...

25 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the original purchaser's use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defe...

32 Safety Instructions and Operator’s Manual for PRO GEAR EXPRESS MID-SIZE WALK BEHIND MOWERS SERIES 0 IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions i...