Snapper Lawn Mower - Manual
Snapper Lawn Mower – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – DRIVE ASSEMBLY; FIGURE 9
- Page 5 – DISCHARGE ASSEMBLY
- Page 6 – WARNING; DO NOT operate without entire Grass Catcher or
- Page 7 – NOTES
- Page 8 – (Details on Pages 1 through 4 of this Instruction); LUBRICATION
1
SET-UP INSTRUCTION & PRE-OPERATION CHECKLIST
SNAPPER 21" STEEL DECK COMMERCIAL RECYCLING WALK MOWERS
INTRODUCTION: The SNAPPER Walk Behind Mowers are shipped almost fully assembled and require minimal
set-up. Complete each of the following steps carefully. Review and complete each item as instructed on the
Pre-Operation checklist. The Snapper Product Registration card must be filled out and sent to Customer
Service department at Snapper when completed.
WARNING – DO NOT ATTEMPT TO START OR
OPERATE THIS UNIT UNTIL ALL ASSEMBLY
STEPS HAVE BEEN COMPLETED. SERIOUS
INJURY OR EQUIPMENT DAMAGE MAY RESULT.
HANDLE ASSEMBLY
STEP 1:
Remove mower from shipping carton. These
mowers are manufactured with (4) 5/16-18 x 2” hex cap
screws, and (4) 5/16 bolt retainers that secure the
upper, middle handles and lower handle brackets
together for packaging purposes. This hardware will
have to be removed and discarded. See Figure 1.
REMOVE EXISTING HARDWARE
FIGURE 1
STEP 2:
New hardware can be found in hardware bag.
Attach middle handle to lower handle brackets using
5/16-18 x 2” curved head bolts, installed from the inside
of handles as shown, and secure with 5/16 internal
tooth lock washers and hex nuts. Do Not tighten at this
time. See Figure 2.
STEP 3:
Attach the upper handle assembly to the middle
handle using 5/16-18 x 1-1/2” curved head bolts,
installed from the inside of handles as shown, and
secure with 5/16 internal tooth lock washers and hex
nuts. Do Not tighten at this time. See Figure 3.
FIGURE 2
FIGURE 3
FIGURE 4
INSTRUCTION No. 7100374 (I.R. 1/11/2006)
TP 300-5113-IR-CW-N
UPPER
HANDLE
MIDDLE
HANDLE
5/16 BOLT
RETAINER
5/16 BOLT
RETAINER
5/16 X 1-1/2” MACHINE
SCREWS
5/16 X 2” HEX
HEAD CAP
SCREWS
MIDDLE
HANDLE
5/16 BOLT
RETAINER
LOWER
HANDLES
MIDDLE
HANDLE
LOWER
HANDLE
(Left Side)
5/16 X 2”
CURVED
HEAD BOLT
5/16 HEX
NUTS
5/16 LOCK
WASHERS
UPPER
HANDLE
MIDDLE
HANDLE
INTERNAL
TOOTH LOCK
WASHER
5/16 X 1-1/2”
CURVED
HEAD BOLTS
HEX NUT
LOWER HANDLE
BRACKET
LOOSEN
THREE NUTS
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
3 DRIVE ASSEMBLY STEP 1: 1. Remove driven disc spring from driven disc assembly as shown. See Figure 9. FIGURE 9 2. Manually adjust driven disc to position shown in Figure 10. FIGURE 10 3. Slide Ground speed control lever fully forward. See Figure 11. 4. Install threaded end of Ground speed control ...
5 DISCHARGE ASSEMBLY NOTE: Discharge assemblies vary by model. Some assembly steps shown may not apply to your model. Your mower comes with a recycling cover already installed, and is ready for use as a recycling mower. The recycling cover is designed to remain on the machine at all times, unless al...
6 3: Install the top wire to the grass bag. Tie the slider to the top wire. Fold bag opening into a "Z" and install slider. See Figure 17. FIGURE 17 4: Install grass bag on the mower as shown in Figure 18. FIGURE 18 WARNING DO NOT operate without entire Grass Catcher or guard in place. Grass...
