Snapper Clean Sweep Triple Catcher - Manual

Page 2 - THIS PAGE INTENTIONALLY BLANK

THIS PAGE INTENTIONALLY BLANK (FOR PLACEMENT ONLY - DO NOT PRINT)

Page 3 - Table of Contents

1 Initial Collector Assembly Assemble Catcher Bags ................................13 Install Cover ...................................................13 Removing & Re-attaching the Triple Catcher Removing the Grass Catcher ........................14 Reattaching the Grass Catcher ..................

Page 4 - SAFETY DECALS; GENERAL WARNINGS; ATTACHMENT DECALS

2 Safety Rules& Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control ofunit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian-gle in text signifies important cautions or warnin...

Page 5 - BEFORE OPERATION; WARNING; REQUIRED ACCESSORIES; AFTER OPERATION; STORING THE GRASS CATCHER; CAUTION

3 General Operating Instructions BEFORE OPERATION Clear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day.If grass is wet, the grass catcher is likely to becomeplugged. For efficient bagg...

Page 7 - Initial Turbo Installation; Install Deflector Hinge Assembly; Install Discharge Baffle; TURBO INSTALLATION; Deflector Removal

Initial Turbo Installation 5 Install Deflector Hinge Assembly 1. Remove the bolts (A, Figure 2) securing the RH arbor cover, then remove the cover from the deck. Discardthe cover and bolts (A). 2. Remove and discard the plastic plugs from the deck at the locations used by bolts (F & B, Figure 5)...

Page 8 - Install Deflector

Initial Turbo Installation 6 Install Deflector 1. See Figure 6. Drill four 13/64” holes from the bottom of the deflector at the pre-molded drill points (A, bot-tom of deflector). 2. Attach the deflector to the support rod wire-form using four #10-14 x 3/4 truss head screws and nylocknuts. A C B Figu...

Page 9 - Install Idler Assembly & Belt Guide

Initial Turbo Installation 7 Install Idler Assembly & Belt Guide 1. See Figure 9. Remove and discard the two taptite screws from locations (E). 2. Insert two 5/16-18 x 7/8 capscrews (C) through the mower deck and arbor. Tighten the capscrews. 3. Mount the idler pulley assembly (A) to the deck us...

Page 10 - Install Belt Cover Plate; Install Turbo Belt; Install Mounting Bracket

Initial Turbo Installation 8 Install Belt Cover Plate 1. Attach the belt cover plate (B, Figure 14) to the sup- port bracket (E) using a 5/16-18 x 1 capscrew (C),washer (D) and nylock nut (F). NOTE: This cover plate must be able to pivot on thesupport bracket. Different belt covers are required ford...

Page 11 - Install Turbo Drive Belt; Secure Belt Cover

Initial Turbo Installation 9 Mower DeckArbor Pulley Mower DeckTurbo Drive Pulley Turbo Drive Pulley Idler Pulleys To Slacken Belt CAUTION Before you begin operating the unit with theTurbo attached, be certain you have read all ofthe safety and operational information on the lastpage of this instruct...

Page 12 - Counter Balance Installation; Front Weight Carrier Installation

Initial Counter Balance & WeightCarrier Installation 10 Figure 1. Counter Balance Installation Figure 2. Front Weight Carrier InstallationA. Holes D. Rod B. Capscrews, E. Clips, Safety 1/2-13 x 1-1/4 F. Carrier, Weight C. Locknut, 1/2-13 B D A L F G H K I J E C M A. Rear Deck Lift LeverB. Trunni...

Page 13 - Installation; HITCH & TUBE INSTALLATION; Install Hitch Plate and Back Plate

Initial Hitch & Tube Installation 11 Figure 1. Install Hitch Plate (Flat Style Bumper)A. Hitch Plate D. Locknuts, 1/2-13 B. Heat Shield E. Upper & Lower C. Capscrews Hex, Bumper 1/2-13 x 1-1/4 F. existing Holes Figure 3. Install Hitch AssemblyA. Back Plate G. Carriage Bolts, B. Support Assem...

Page 14 - Initial Hitch & Tube Installation; Install Tubes & Deflector

Initial Hitch & Tube Installation 12 Figure 5. Assemble Tubes & Deflector A B G D H K F M L E C A. DeflectorB. Back PlateC. Capscrew, 5/16-18 x 1 D. SocketE. Washer, 5/16 F. Locknut, 5/16-18G. Upper TubeH. Middle TubeI. Lower Tube J. Washer, #10 K. Capscrew, #10-32 x 1/2 L. Nut, #10-32M. Cli...

Page 15 - COLLECTOR ASSEMBLY; Assemble Catcher Bags

Initial Collector Assembly 13 COLLECTOR ASSEMBLY Assemble Catcher Bags 1. See Figure 1. Insert the wire hoop (H) through the cloth bag (B). 2. Install the clamp (E) and hanger bracket (D). Secure with two 5/16-18 x 3/4 carriage bolts (C), lockwashers(G) and nuts (F). Install Cover 1. See Figure 2. H...

Page 16 - Removing the Grass Catcher & Tubes

Removing & Re-attaching GrassCatcher 14 REMOVING & RE-ATTACHING THEGRASS CATCHER Removing the Grass Catcher & Tubes 1. Remove the hair pin clips (D, Figure 1) and hinge pins (B) and remove the cover (A). 2. Remove the bags (A, Figure 2) by lifting them off their hooks. Empty any grass ou...

Page 17 - Removing and Re-attaching Grass Catcher; Re-attaching the Grass Catcher

Removing and Re-attaching Grass Catcher 15 Figure 8. Install HInge PinsA. Cover C. Hinge B. Hinge Pin D. Hair Pin Clip A B C D Figure 7. Install CoverA. Cover C. Hinges B. Bags A C B Figure 6. BagsA. BagsB. Back Plate A Re-attaching the Grass Catcher 1. Set the back plate and support (A, Figure 5) o...

Snapper Clean Sweep Triple Catcher - Manual

Table of Contents:

Summary

Other Snapper Models