Snapper Clean Sweep Triple Catcher - Manuals

3 General Operating Instructions BEFORE OPERATION Clear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day.If grass is wet, the grass catcher is likely to becomeplugged. For efficient bagg...

Initial Turbo Installation 5 Install Deflector Hinge Assembly 1. Remove the bolts (A, Figure 2) securing the RH arbor cover, then remove the cover from the deck. Discardthe cover and bolts (A). 2. Remove and discard the plastic plugs from the deck at the locations used by bolts (F & B, Figure 5)...

Initial Turbo Installation 6 Install Deflector 1. See Figure 6. Drill four 13/64” holes from the bottom of the deflector at the pre-molded drill points (A, bot-tom of deflector). 2. Attach the deflector to the support rod wire-form using four #10-14 x 3/4 truss head screws and nylocknuts. A C B Figu...

Initial Turbo Installation 7 Install Idler Assembly & Belt Guide 1. See Figure 9. Remove and discard the two taptite screws from locations (E). 2. Insert two 5/16-18 x 7/8 capscrews (C) through the mower deck and arbor. Tighten the capscrews. 3. Mount the idler pulley assembly (A) to the deck us...

Initial Turbo Installation 8 Install Belt Cover Plate 1. Attach the belt cover plate (B, Figure 14) to the sup- port bracket (E) using a 5/16-18 x 1 capscrew (C),washer (D) and nylock nut (F). NOTE: This cover plate must be able to pivot on thesupport bracket. Different belt covers are required ford...

Initial Turbo Installation 9 Mower DeckArbor Pulley Mower DeckTurbo Drive Pulley Turbo Drive Pulley Idler Pulleys To Slacken Belt CAUTION Before you begin operating the unit with theTurbo attached, be certain you have read all ofthe safety and operational information on the lastpage of this instruct...

Initial Counter Balance & WeightCarrier Installation 10 Figure 1. Counter Balance Installation Figure 2. Front Weight Carrier InstallationA. Holes D. Rod B. Capscrews, E. Clips, Safety 1/2-13 x 1-1/4 F. Carrier, Weight C. Locknut, 1/2-13 B D A L F G H K I J E C M A. Rear Deck Lift LeverB. Trunni...

Initial Hitch & Tube Installation 11 Figure 1. Install Hitch Plate (Flat Style Bumper)A. Hitch Plate D. Locknuts, 1/2-13 B. Heat Shield E. Upper & Lower C. Capscrews Hex, Bumper 1/2-13 x 1-1/4 F. existing Holes Figure 3. Install Hitch AssemblyA. Back Plate G. Carriage Bolts, B. Support Assem...

Initial Hitch & Tube Installation 12 Figure 5. Assemble Tubes & Deflector A B G D H K F M L E C A. DeflectorB. Back PlateC. Capscrew, 5/16-18 x 1 D. SocketE. Washer, 5/16 F. Locknut, 5/16-18G. Upper TubeH. Middle TubeI. Lower Tube J. Washer, #10 K. Capscrew, #10-32 x 1/2 L. Nut, #10-32M. Cli...

Initial Collector Assembly 13 COLLECTOR ASSEMBLY Assemble Catcher Bags 1. See Figure 1. Insert the wire hoop (H) through the cloth bag (B). 2. Install the clamp (E) and hanger bracket (D). Secure with two 5/16-18 x 3/4 carriage bolts (C), lockwashers(G) and nuts (F). Install Cover 1. See Figure 2. H...

Removing & Re-attaching GrassCatcher 14 REMOVING & RE-ATTACHING THEGRASS CATCHER Removing the Grass Catcher & Tubes 1. Remove the hair pin clips (D, Figure 1) and hinge pins (B) and remove the cover (A). 2. Remove the bags (A, Figure 2) by lifting them off their hooks. Empty any grass ou...

Removing and Re-attaching Grass Catcher 15 Figure 8. Install HInge PinsA. Cover C. Hinge B. Hinge Pin D. Hair Pin Clip A B C D Figure 7. Install CoverA. Cover C. Hinges B. Bags A C B Figure 6. BagsA. BagsB. Back Plate A Re-attaching the Grass Catcher 1. Set the back plate and support (A, Figure 5) o...