Snapper 7600024, 7600023 - Manual
Snapper 7600024, 7600023 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 5 – ATTACH TO ALL
- Page 6 – Assembly is complete.
- Page 7 – WARNING
- Page 8 – TWIN BAG CATCHER COMPONENTS - 38” RZT / JAVELIN
- Page 12 – TWIN BAG CATCHER COMPONENTS - 42” RZT / JAVELIN
1
#7600023 & 7600024 TWIN BAG CATCHER KIT FOR
38 & 42” SNAPPER / SIMPLICITY RZT RIDING MOWERS
WARNING
DO NOT attempt any adjustments, maintenance, repairs, or service with engine running. Stop engine. Engage
parking brake. Remove key. Remove spark plug wire and secure wire away from spark plug. Engine, muffler and
surrounding areas are extremely hot. Avoid serious burns; allow components to cool down before installing kit.
Replace worn or damaged parts prior to operating. Use approved fuel container. DO NOT smoke near open fuel
container. DO NOT fill fuel tank indoors or when engine is running. Allow engine to cool for at least ten minutes
before refilling. Make sure that fuel cap is tightened securely. Wipe off any spilled fuel before starting engine.
!
STEP 1 (38” Units Only):
Install one air lift onto the topside
of each of the four blade tips, securing with three 5/16-24 x
5/8” oval head machine screws, internal tooth lock washers
and hex nuts. See Figure 1. Torque hardware to 12 ft-lbs.
STEP 2:
Install the baffle to the front of the mower deck:
38” Decks
- Secure the baffle with one 5/16 x 3/4” hex head
cap screw, flat washer and center lock nut on one end, and
the existing hardware on the other end. See Figure 2.
42” Decks
- Secure the baffle with two 5/16 x 5/8” pan head
machine screws and flange lock nuts. See Figure 3.
NOTE:
One or more holes may have to be drilled into the
deck in order to install the baffle. If so, install the baffle as
fully onto the deck as possible with the existing holes, then
drill the remaining holes with an 11/32” drill, using the baffle
hole(s) as a template.
FIGURE 1
INSTRUCTION No. 7100642 (Rev. 2, 12/14/2006)
TP 200-5173-R2-AT-SN
SECURE AIR LIFT
TO TOP OF BLADE
FIGURE 2
INSTALL BAFFLE
TO OUTSIDE
FRONT OF DECK
!
WASHER
AND NUT (3)
38” DECK
USE
EXISTING
NUTS
HEX HEAD CAP
SCREW
WASHER AND
LOCK NUT
(Components removed for clarity)
MACHINE
SCREW (3)
FIGURE 3
42” DECK
MACHINE
SCREW (2)
LOCK NUT (2)
INSTALL BAFFLE TO OUTSIDE
FRONT OF DECK
NOTE: CASTER
MAY DIFFER FROM
ONE SHOWN
NOTE: Refer to the parts lists at the end of this manual for
additional assistance with component identification.
7600023
TWIN BAG CATCHER KIT FOR 38” SNAPPER / SIMPLICITY RZT RIDING MOWER
7600024
TWIN BAG CATCHER KIT FOR 42” SNAPPER / SIMPLICITY RZT RIDING MOWER
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
STEP 12: Assemble the discharge tubes: a. Install one strap assembly to each of the locations marked ‘A’ in Figure 19. Insert one #10-24 x 5/8” pan headscrew, fitted with one #10 x 1/2” OD flat washer, out throughthe hole in the tube or adapter. Secure with one #10 x 3/4”OD flat washer, strap, and #...
STEP 13: Assemble the grass containers: a. Match the numbers on the side of each container segment with its corresponding segment. ‘1’s and ‘2’sdesignate the first container, ‘3’s and ‘4’s designate thesecond. See Figure 21. b. With the matched numbers aligned, insert the bottom segment of each cont...
Operation: To use the bagger: -Start the engine.-Move the throttle control to the fast position.-To fill the containers, always operate at a slow groundspeed. To check and clean the discharge tubes: -Stop machine motion, turn off the blades, stop the engine.-Disconnect the straps securing the discha...
