Smeg SE644ID1- User Manual

Instructions for the User 34 4. BEFORE FIRST USE 5. INTENDED USE OF THE APPLIANCE Do not leave packaging unattended in the home environment. Separate the various waste materials andtake them to the nearest differentiated waste collection centre.Remove all the REMOVABLE labels and any protective film...

Instructions for the User 35 6. DESCRIPTION OF THE APPLIANCE AND THE CONTROLS ON THE FRONT PANEL 6.1 The hob The hob is an induction hob. An induction coil located under the glass ceramic cooking surface createsan alternating electromagnetic field which enters the glass ceramic and induces a thermal...

Instructions for the User 36 6.3 Limitation on the duration of use The hob has an automatic device which limits the duration of use. The duration of operation of each cooking zone depends on the power level selected (see table). The assumption is that no changes are made to the settings of the cooki...

Instructions for the User 37 Carry out the magnet test described below or check whether the container bears thestamp indicating that it is suitable for cooking with an induction current. Magnet test: Move the magnet towards the base of your cooking container. If the magnet isattracted, you can use t...

Instructions for the User 38 6.9 Residual heat indicator The hob is equipped with a residual heat indicator in the form of the symbol. When is displayed after the heat has been switched off, it indicates that the residual heat can be used to keep food hot or melt certain foods. The cooking zone may ...

Instructions for the User 40 8. USING THE HOB 8.1 Warnings and general advice To operate a hob equipped with touch controls, lightly press the symbols printed on the surface of thehob. Every pressure on a symbol is confirmed by a control beep. On first connection to the electrical mains, an operatin...

Instructions for the User 41 8.3 Switching on the hob and the cooking zone To activate the control described here, after pressing one (selection) button, you need to press anotherone afterwards . The second button needs to be pressed within 10 seconds , as otherwise the desired selection will be dea...

Instructions for the User 43 8.9 Quick start cooking Using this function, cooking starts at level 9 then is automatically reduced (levels 1 to 8) after adetermined period of time. When the quick start cooking function is activated, the power level alsoneeds to be set for the normal cooking period wh...

Instructions for the User 44 8.10 Cooking guidelines The table below shows the power values which can be set, together with the corresponding type of food.Settings may vary depending on the amount of food and personal taste. SETTING TYPE OF FOOD 1 To melt butter, chocolate or similar products. 2 - 3...

Instructions for the User 45 9. CLEANING AND MAINTENANCE Before performing any operations , switch off the power supply to the appliance. 9.1 Cleaning the glass ceramic hob The glass ceramic hob should be regularly cleaned, preferably after every use, once the residual heatwarning lights have gone o...

Instructions for the User 46 10. TROUBLE-SHOOTING PROBLEM POSSIBLE CAUSES SOLUTION The hob does not work. - The hob is not wired in or the main switch is not on. - There is a power failure.- The fuse or the magnetothermal switch of the appliance has blown. - The sensor buttons are locked (child safe...

Instructions for the installer 47 11. INSTALLATION 11.1 Safety instructions for installing kitchen furniture • Veneers, adhesives or plastic coatings on adjacent furniture should be temperature-resistant (>75°C). If they are not sufficiently temperature-resistant, they may warp over time. • When ...

Instructions for the installer 48 11.3 Positioning • If there are other pieces of furniture (lateral walls, drawers, etc.) under the hob, a double-layer base must be installed at least 20 mm from the bottom of the hob to avoid any accidental contact. It mustonly be possible to remove the double-laye...

Instructions for the installer 49 11.6 Inserting the hob into the hole in the work surface Be very careful when inserting the hob. If the process is not followed correctly as described, the hob maybe damaged. • Insert the hob, resting the frame completely on the back edge of the hole in the work sur...

Instructions for the installer 50 11.8 Technical information • Hob model See rating plate • Electrical connections 220-240V~ 50/60Hz / 380-415V 2N~ 50/60Hz • HOB RATING I • Maximum power See rating plate 11.9 The rating plate Make sure that the voltage and capacity of the power line conform to the d...

Instructions for the installer 51 If the cable needs replacing, an original spare can be ordered from Authorised Service Centres. The manufacturer cannot be held liable for damage to persons or things caused by failure to observe the above instructions or by tampering with any part of the appliance....

Instructions for the installer 52 11.12 Power limiter release The hob leaves the factory with the power limited to 2.8 kW. This setting can be removed as indicatedbelow, after which the power will no longer be limited and the hob maximum power will be 7.4kW. After having connected the hob to the pow...