Page 4 - Copyright
Copyright Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or ...
Page 5 - Limited Warranty
L IMITED W ARRANTY i Limited Warranty Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the ...
Page 6 - ii
L IMITED W ARRANTY ii WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITI...
Page 7 - iii; OMPLIANCES
iii C OMPLIANCES FCC - Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment ...
Page 8 - iv
C OMPLIANCES iv Industry Canada - Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.Cet appareil numér...
Page 9 - ABLE
T ABLE OF C ONTENTS v T ABLE OF C ONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Description of Hardware . . . . . . . . . . . . . . . . . . . . . . 1 Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Front...
Page 11 - NTRODUCTION; Description of Hardware
1 I NTRODUCTION I NTRODUCTION This manual describes how to install and use SMC’s EZSwitch™ 10/100. It features 16 10/100 M bp s Auto Negotiation sw it ch ports, and provides the flexibility to fit into your working space with network environment. The EZSwitch™ 10/100 can be used to connect with PCs,...
Page 12 - Front Panel LEDs; Port and Switch Status LEDs; LEDs
I NTRODUCTION 2 connections to servers and workstations to be made with straight-through cabling • “At-a-glance” LEDs for port and system status monitoring • Jabber lock-up function automatically stops transmission of abnormal frames to prevent network disruption • Automatic polarity detection and c...
Page 13 - Rear Panel
I NTRODUCTION 3 SMC-EZ6516TX Rear Panel These EZ Switch 10/100 models feature 16 10BASE-T/100BASE-TX ports with RJ-45 connectors located on the rear panel of the Switch. Each port contains a built-in wiring crossover (MDI-X) that allows for the use of straight-through twisted-pair cable for connecti...
Page 14 - NSTALLING; Equipment Checklist
I NSTALLING THE S WITCH 4 I NSTALLING THE S WITCH The EZ Switch 10/100 can be placed on a desktop or shelf and stacked with other devices using the provided 4 rubber foot pads Equipment Checklist After unpacking the EZ Switch 10/100, check the contents of the box to be sure you’ve received the follo...
Page 15 - Instructions
I NSTALLING THE S WITCH 5 • There should be adequate space (approximately two inches) on all sides for proper air flow. • Make sure twisted-pair cable is always routed away from power lines, fluorescent lighting fixtures and other sources of electrical interference such as radios, transmitters, etc....
Page 16 - AMPLE; Standalone Switch
S AMPLE A PPLICATIONS 6 S AMPLE A PPLICATIONS Some typical applications for the SMC-EZ6516TX are illustrated below: Standalone Switch Cascading Switches 100 MbpsServers 100 MbpsSer ver
Page 17 - ROUBLESHOOTING
T ROUBLESHOOTING 7 T ROUBLESHOOTING 1. Symptom Power LED does not light after power on. Probable Causes Power outlet or power cord may be defective. Possible Solutions • Check for loose connections. • Check the power outlet by using it for another device. • Replace the power cord. 2. Symptom Link LE...
Page 18 - Cable Type and Connector
C ABLE S PECIFICATIONS 8 C ABLE S PECIFICATIONS Cable Type and Connector RJ-45 Connector Pin Assignments Caution: DO-NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards. An Ethernet or Fast Ethernet twisted-pair link...
Page 19 - ments
C ABLE S PECIFICATIONS 9 Note: The “+” and “-” signs are used to represent the polarity of the wires that make up each wire pair. RJ-45 Pin Assign- ments Straight-Through Cable RJ-45 Pin Assign- ments Crossover Cable End 1 End 2 End 1 End 2 1 (Tx+) 1 (Tx+) 1 (Tx+) 3 (Rx+) 2 (Tx-) 2 (Tx-) 2 (Tx-) 6 (...
Page 20 - PECIFICATIONS; Full line rate
S PECIFICATIONS 10 S PECIFICATIONS EZ Switch 10/100 General Network Interface RJ-45: 100 ohm, UTP cable 10BASE-T - Categories 3, 4, or 5100BASE-TX - Category 5 LEDs Power - one Speed - one per portLink/Activity - one per port FDX - one per port Filtering/Forwarding/Learning Rates Full line rate Temp...
