Singer SE300 - Manual - manualsarea.com

Page 2 - Shopping List

Shopping List Everything you need to complete this project in one place. Use this convenient checklist toensure you have all required materials in your sewing room, or take it with you while you shop forsupplies. o SINGER® Legacy ™ SE300 Sewing and Embroidery Machine o 2 - 3 colorful cotton fat quar...

Page 3 - Cutting Instructions:

Supplies forEmbroidery: ○ Small Embroidery Hoop - (4” x 4”) ○ INSPIRA® Aqua Magic ™ Stabilizer ○ Coordinating Embroidery Thread ○ Straight Edge Ruler Cutting Instructions: ○ Outer Body x2 - 8½” x 5” ○ Body Lining x2 - 8½” x 5” ○ Single Sided Fusible Batting x2 - 8½” x 5” ○ Zipper Pocket - 8½” x 4” (...

Page 4 - Optional Embroidery Instructions:; Cut Zipper Pocket Fabric to roughly 91⁄2” x 5”.

Optional Embroidery Instructions: 1. Hoop Stabilizer. 2. Cut Zipper Pocket Fabric to roughly 9½” x 5”. 3. Center Zipper Pocket Fabric in hoop & pin or hoop in place. 4. Load embroidery monogram/design created in mySewnet ™ Software on your SINGER® Legacy ™ SE300 Sewing & Embroidery Machine. ...

Page 6 - Square up the Zipper Pocket Fabric to a size of 81⁄2” x 4”.

9. Square up the Zipper Pocket Fabric to a size of 8½” x 4”. Project Steps: 1. Gather materials. 2. Using the SINGER® SteamCraft Steam Iron fuse one of the Outer Body pieces to one of the Single Sided Fusible Batting pieces. Do this for both Outer Body pieces. Singer, the Cameo “S” Design and Design...

Page 10 - top of the long side.

12. Take one of the Outer Body pieces & with the marking pen draw a line 1½” from the top of the long side. 13. Lay the Zipper Pocket section right side down so that the lining side is up with the unsewn zipper side lining up with the line drawn in the previous step & pin in place. Singer, t...

Page 11 - zipper pull if needed when sewing the zipper in place.

14. Sew the un-sewn side of the zipper in place with a ¼” seam. Don’t forget to move the zipper pull if needed when sewing the zipper in place. 15. Fold the pocket section back over & press using the SINGER® SteamCraft Steam Iron. Singer, the Cameo “S” Design and Design and Sewing Made Easy are ...

Page 16 - Sew along both long edges of the strap to hold in place.

29. Fold the strap piece in half & press in place. The ﬁnished size should be roughly ½” wide. 30. Sew along both long edges of the strap to hold in place. Singer, the Cameo “S” Design and Design and Sewing Made Easy are trademarks of The Singer Company Limited S.a.r.l. or its Affiliates. © 2021...

Page 18 - Take the long strap & place the swivel hook on it.

34. Place the D-Ring strip piece between the Zipper Pocket zipper & the Outer Section zipper. Sew in place. Pro-Tip: Be sure to move the Lining of the front Outer Section out of the way prior tosewing the D-Rind strip piece in place. 35. Take the long strap & place the swivel hook on it. Sin...

Page 20 - sides together. Pin or clip all the way around.

39. Place the strap loop together & sew in place about ½” from the swivel hook. 40. Open the sections up so that the Lining pieces as well as the Outer pieces are right sides together. Pin or clip all the way around. Pro-Tip: It can be helpful to line up the zipper teeth on either side so that t...

Page 21 - bottom of the lining piece for turning.

41. Sew a ½” seam allowance all the way around. Leaving a 4” to 5” opening at the bottom of the lining piece for turning. Pro-Tip: Remember to back stitch at the beginning & end to keep the stitches fromcoming out when turning right side out. Pro-Tip: It's helpful to back stitch over the zipper ...

Singer SE300 - Manual

Table of Contents:

Other Manuals for Singer SE300

Summary

Other Singer Models