Shure 44 - Manual
Shure 44 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Table 2. Cartridge Specifications; •Configuración no ortodoxa para locutores (Figura; Setting a Precise Tracking Force; • DJs: Don’t use more tracking force than; Figure 9
- Page 3 – Zusätzlicher Überspringwiderstand für DJs; Installation des Tonabnehmers
- Page 4 – 拾音头安装说明; 全面两年保修; カートリッジの取付け方; カートリッジの位置設定方法の選択; 年間完全保証
Shure cartridges can be used in DJ or Hi-Fi applications.
Note: The
M70BX
is not recommended for heavy scratching.
25, 35, and 44 Series
Phono Cartridges
Install Your Cartridge
Carefully remove the stylus from the cartridge. See
1.
Figure 1.
Use needle-nose pliers to connect the colored wires
2.
from the tonearm headshell to the corresponding
pins on the cartridge. See Table 1 and Figure 2.
NOTE:
The larger terminal goes onto the
M25C
cartridge and the smaller terminal goes onto the
arm of the turntable.
HEADSHELL WIRE
COLOR
PIN
RIGHT “HOT”
RED
R
RIGHT GROUND
GREEN
RG
LEFT “HOT”
WHITE
L
LEFT GROUND
BLUE
LG
Figure 2
Figure 3
Figure 4
Standard DJ Setup:
Mount cartridge at rear of headshell. Set tonearm height to 4-5. Set tracking force
to 3 grams. Set anti-skate control to 0.
Figure 5
Choose a Method for Cartridge Positioning
Hi-Fi Setup:
For maximum fidelity and minimal record wear, position the cartridge using an alignment
protractor or the overhang gauge supplied with your turntable. Level your tonearm (See Figure 7). Use
Table 2 and “Setting a Precise Tracking Force”, below, to set the typical tracking force for your cartridge.
Set the anti-skate control to the same number as the tracking force.
4 - 5
3 grams
4 - 5
0
Unorthodox DJ Setup:
Reverse the counterweight and mount it flush with the end of the tonearm.
Mount cartridge (with headshell weight) flush with the front edge of the headshell. Set anti-skate
control to 0.
Figure 6
Level Your Tonearm
Figure 7
Extra Skip Resistance for DJ’s:
0
23
O
Mount the cartridge at a 23 degree angle as
shown, so that the cartridge points to the tonearm
pivot. Set anti-skate to 0.
©2008, Shure Incorporated
27C3116 (Rev. 4)
Printed in U.S.A.
Table 1. Cartridge Wiring
Attach the cartridge to the headshell using the screws
1.
supplied. See Figure 3. Tighten the screws after
positioning the cartridge (and headshell weight, if
desired) according to one of the methods described
below.
Carefully insert the stylus into the cartridge.
2.
Figure 1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Cartridge Replacement Stylus Stylus Color Stereo Output (1 KHz at 5 cm/sec peak recorded velocity) Frequency Response in Hz Tracking force range (grams) Typical Tracking Force (grams) M44-7 N44-7 White 9.5 mV 20 to 20,000 1-3 3 M44G N44G Gray 6.2 mV 20 to 20,000 .75-1.5 1.5 M35S N35S Chartreuse 5.0m...
Shure-Tonabnehmer können für DJ- oder Hi-Fi- Anwendungen verwendet werden. Hinweis: Der M70BX wird nicht für starkes „Scratching“ empfohlen. Die Abtastnadel vorsichtig aus dem Tonabnehmer 1. entfernen. Siehe Abbildung 1. Mit einer Nadelzange wie in 2. Tabelle 1 angeführt die Drähte vom Tonarmkopf an...
United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A. Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446 Europe, Middle East, Africa: Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414 Asia, Pacific: Shure Asia Limited, Phone: 85...
