Page 3 - USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!; Contents
SE TU P EL EC TR IC A L M A INTEN A N CE SE RV IC E PA RT S O PE R ATIONS SA FE T Y IN TR O DUCT IO N USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST! INTRODUCTION...................................... 2 Woodstock Technical Support .................. 2 Machine Specifications ............
Page 4 - INTRODUCTION
-2- Model W1875 (For Machines Mfd. Since 1/20) IN TR O DU CT IO N INTRODUCTION Woodstock.Technical.Support This machine has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and relia...
Page 5 - HP BENCHTOP TABLE SAW WITH STAND
-3- Model W1875 (For Machines Mfd. Since 1/20) IN TR O DUCT IO N Model W1875 Machine Specifications, Page 1 of 3 MODEL W1875 2 HP BENCHTOP TABLE SAW WITH STAND Product Dimensions Weight........................................................................................................... 70 lbs....
Page 8 - Identification
-6- Model W1875 (For Machines Mfd. Since 1/20) IN TR O DU CT IO N Identification Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual. Fence Fence Micro-Adjust Knob Fence Lock Roller Stand Blade Height/Tilt Handwhe...
Page 11 - NOTICE; SAFETY
-9- Model W1875 (For Machines Mfd. Since 1/20) SA FE T Y Indicates.a.potentially.hazardous.situation.which,.if.not.avoided,. MAY.result.in.minor.or.moderate.injury. Indicates.an.imminently.hazardous.situation.which,.if.not.avoided,. WILL.result.in.death.or.serious.injury. Indicates.a.potentially.haz...
Page 15 - ELECTRICAL
-13- Model W1875 (For Machines Mfd. Since 1/20) EL EC TR IC A L ELECTRICAL Circuit.Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is a...
Page 17 - TU; SETUP; Unpacking
-15- Model W1875 (For Machines Mfd. Since 1/20) SE TU P SETUP Unpacking This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Description. Qty • An Assistant .............
Page 18 - USE THIS CHART TO IDENTIFY
-16- Model W1875 (For Machines Mfd. Since 1/20) SE TU P Hex Wrench 16mm MEASURE BOL T DIAMETER BY PLACING INSIDE CIRCLE 7 ⁄ 16 " 3 ⁄ 8 " 1 ⁄ 4 " 5 ⁄ 16 " #10 1 ⁄ 2 " W ASHERS ARE MEASURED BY THE INSIDE DIAMETER USE THIS CHART TO IDENTIFY HARDWARE DURING THE INVENTORY/ASSEMBLY PRO...
Page 19 - Inventory
-17- Model W1875 (For Machines Mfd. Since 1/20) SE TU P Table.Saw.Inventory.(Figure.5). Qty A.. Main Table Saw Unit (Not Shown) .......................1 B.. Miter Gauge ................................................1 C. Blade Guard ................................................1 D.. Push Stick ....
Page 20 - Assembly
-18- Model W1875 (For Machines Mfd. Since 1/20) SE TU P Machine.Placement Workbench.Load Refer to the Machine.Specifications for the weight and footprint specifications of your machine. Some workbenches may require additional reinforcement to support the weight of the machine and workpiece materials...
Page 24 - OPERATIONS; General
-22- Model W1875 (For Machines Mfd. Since 1/20) O PE R ATIO NS OPERATIONS General This machine will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written wi...
Page 25 - PE
-23- Model W1875 (For Machines Mfd. Since 1/20) O PE R ATIONS Workpiece.Inspection Some workpieces are not safe to cut or may require modification before they can be made safe to cut. Before.cutting,.get.in.the.habit.of.inspecting. all.workpieces.for.the.following : • Material Type: This machine is ...
Page 28 - Triple
-26- Model W1875 (For Machines Mfd. Since 1/20) O PE R ATIO NS Figure.21. Example of a laminate blade. Triple Chip Blade Laminate.Blade.Features.(Figure.21): • Best for cutting plywood or veneer • 40-80 teeth • Triple chip tooth profile • Very shallow gullet Thin.Kerf.Blade: A blade with thinner ker...
Page 30 - Installing Blade Guard & Spreader/Riving Knife
-28- Model W1875 (For Machines Mfd. Since 1/20) O PE R ATIO NS Blade.Guard.Assembly The term "blade guard" refers to the assembly that consists of the clear polycarbonate shield, the spreader, and the anti-kickback pawls on each side of the spreader (see Figure.25 ). Each of these components...
Page 34 - When Not to Use Riving Knife
-32- Model W1875 (For Machines Mfd. Since 1/20) O PE R ATIO NS Top hole / down position = riving knife position. Bottom hole / up position = blade guard position. Figure.34. Riving knife mounting positions. To.ensure.riving.knife.works.safely,.it. MUST.be.aligned.with.and.correctly. adjusted.to.blad...
Page 35 - Ripping
-33- Model W1875 (For Machines Mfd. Since 1/20) O PE R ATIONS Ripping Ripping means cutting with the grain of a natural wood workpiece. In man-made materials such as MDF or plywood, ripping simply means cutting lengthwise. To.make.a.rip.cut,.do.these.steps: 1 . Review Preventing.Kickback on Page.12....
Page 36 - Crosscutting
-34- Model W1875 (For Machines Mfd. Since 1/20) O PE R ATIO NS Crosscutting "Crosscutting" means cutting across the grain of a natural wood workpiece, usually with a miter saw. In other man- made materials, such as MDF or plywood, crosscutting means cutting across the width of the workpiece....
Page 43 - Featherboards
-41- Model W1875 (For Machines Mfd. Since 1/20) O PE R ATIONS SHOP-MADE.SAFETY.ACCESSORIES Featherboards Easily made from scrap stock, featherboards provide an added degree of protection against kickback, especially when used together with push sticks. They also maintain pressure on the workpiece to...
Page 48 - ACCESSORIES
-46- Model W1875 (For Machines Mfd. Since 1/20) O PE R ATIO NS ACCESSORIES Table.Saw.Accessories The following table saw accessories may be available through your local Woodstock International Inc. Dealer. If you do not have a dealer in your area, these products are also available through online dea...
Page 49 - CE; MAINTENANCE
-47- Model W1875 (For Machines Mfd. Since 1/20) M A INTEN A N CE MAINTENANCE Cleaning the Model W1875 is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it. Cleaning.&.Pro...
Page 50 - Lubrication
-48- Model W1875 (For Machines Mfd. Since 1/20) M A INTE N A N CE Lubrication It is essential to clean components before lubricating them because dust and chips build up on lubricated components and make them hard to move. Simply adding more grease to them will not yield smooth moving components. Cl...
Page 51 - SERVICE
-49- Model W1875 (For Machines Mfd. Since 1/20) SE RV IC E SERVICE General The blade angle indicator has been set by the factory to show 0° when the blade is at 90° and should require no adjustments unless you notice that your cuts are not accurate. Blade.Angle.Indicator Tools.Needed. Qty 90° Square...
Page 53 - Alignment
-51- Model W1875 (For Machines Mfd. Since 1/20) SE RV IC E Table Riving Knife Top Alignment Bottom Alignment Figure.67. Example of checking top and bottom riving knife parallelism with blade. Alignment Zone Spreader or Riving Knife Blade Figure.68. Spreader/riving knife alignment zone. 6. Loosen (4)...
Page 56 - Adjustment
-54- Model W1875 (For Machines Mfd. Since 1/20) SE RV IC E Table/Dado.Insert. Adjustment The table/dado insert must sit perfectly flush with the table to provide a smooth, continuous surface for the workpiece to slide over. The insert is held in place by a magnet and sits on top of four adjustment s...
Page 61 - Operation
-59- Model W1875 (For Machines Mfd. Since 1/20) SE RV IC E PROBLEM POSSIBLE.CAUSE CORRECTIVE.ACTION Fence does not move smoothly. 1. Fence not mounted/adjusted correctly.2. Rails dirty or sticky. 1. Remount fence and adjust correctly.2. Clean and lubricate/wax rails. Material moves away from fence w...
Page 63 - WIRING DIAGRAM COLOR KEY
-61- Model W1875 (For Machines Mfd. Since 1/20) SE RV IC E Electrical.Safety.Instructions SHOCK.HAZARD. Working on wiring that is connected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or...
Page 64 - Universal Motor; Switch Box; STOP; Electrical.Components
-62- Model W1875 (For Machines Mfd. Since 1/20) SE RV IC E Wiring.Diagram Universal Motor (120V) The motor wiring shown here is current at the time of printing, but it may not match your machine. Always use the wiring diagram inside the motor junction box. ON/OFF Button Switch Circuit Breaker AW NEU...
Page 65 - RT; PARTS
-63- Model W1875 (For Machines Mfd. Since 1/20) PA RT S PARTS Trunnions.&.Blade 10 11 12 13 14 15 16 17 18 19 19 20 21 22 23 24 25 26 27 28 29 30 31 32 32 33 33 34 35 36 37 38 39 40 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 60 REF PART # DESCRIPTION REF PART # DESCRIPTION 10...
Page 72 - Base
-70- Model W1875 (For Machines Mfd. Since 1/20) PA RT S Base 800 801 802 803 804 805 806 807 808 808 809 810 811 812 813 815 814 REF PART # DESCRIPTION REF PART # DESCRIPTION 800 X18750800 TABLE SAW BASE ASSEMBLY 808 X18750808 TAP SCREW 4 X 16 801 X18750801 ROUND KNOB M8-1.25 809 X18750809 ANTI-KICK...
Page 75 - WARRANTY
WARRANTY Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, neglige...
