Page 3 - USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!; Contents
SE TU P EL EC TR IC A L M A INTEN A N CE SE RV IC E PA RT S O PE R ATIONS SA FE T Y IN TR O DUCT IO N USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST! INTRODUCTION...................................... 2 Machine Description ............................. 2 Woodstock Technical Support ....
Page 4 - INTRODUCTION
-2- Model W1864/W1865 (For Machines Mfd. Since 02/19) IN TR O DU CT IO N INTRODUCTION Machine.Description Models W1864 and W1865 are CSA-certified, 5 HP, 20" planers with the following differences: • Model.W1864 has a 4-knife cutterhead, magnetic ON/OFF switch mounted to the headstock, and rolle...
Page 9 - Identification
-7- Model W1864/W1865 (For Machines Mfd. Since 02/19) IN TR O DUCT IO N Identification Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual. To. reduce. your. risk. of. serious. injury. or. damage. to. the. machine...
Page 12 - NOTICE; SAFETY
-10- Model W1864/W1865 (For Machines Mfd. Since 02/19) SA FE T Y Indicates.a.potentially.hazardous.situation.which,.if.not.avoided,. MAY.result.in.minor.or.moderate.injury. Indicates.an.imminently.hazardous.situation.which,.if.not.avoided,. WILL.result.in.death.or.serious.injury. Indicates.a.potenti...
Page 15 - ELECTRICAL
-13- Model W1864/W1865 (For Machines Mfd. Since 02/19) EL EC TR IC A L ELECTRICAL Circuit.Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circu...
Page 16 - Grounding.Requirements
-14- Model W1864/W1865 (For Machines Mfd. Since 02/19) EL EC TR IC A L Grounding.Requirements This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel—in order to reduce the risk of electr...
Page 17 - TU; SETUP; Unpacking
-15- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE TU P SETUP Unpacking This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Description. Qty • Additional Peopl...
Page 18 - Inventory
-16- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE TU P Inventory The following is a list of items shipped with your machine. Before beginning setup, lay these items out and inventory them. Note: If you cannot find an item on this list, carefully check around/inside the machine and packaging ...
Page 20 - Electrical.Installation
-18- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE TU P Figure.9. Working clearances. Machine.Placement Weight.Load Refer to the Machine.Specifications for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional e...
Page 22 - Assembly
-20- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE TU P Assembly Before beginning the assembly process, refer to Items. Needed.for.Setup and gather everything you need. Ensure all parts have been properly cleaned of any heavy-duty rust-preventative applied at the factory (if applicable). Be s...
Page 24 - Level
-22- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE TU P Checking.Gearbox.Oil. Level Before starting your machine for the first time, check the gearbox oil level. The proper oil level is just even with the bottom of the fill plug hole. The gearbox uses ISO 320 gear oil. However, SAE 140 gear o...
Page 25 - TWIST
-23- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE TU P Test.Run TWIST To reset switch, twist button clockwise. Figure.17. Resetting the switch. Serious. injury. or. death. can. result. from. using. this. machine. BEFORE. understanding. its. controls. and. related. safety.information..DO.NOT....
Page 26 - Adjustments
-24- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE TU P Recommended. Adjustments The adjustments listed below have been performed at the factory. However, because of the many variables involved with shipping, we recommend that you verify the adjustments to ensure the best possible results fro...
Page 27 - PE; OPERATIONS
-25- Model W1864/W1865 (For Machines Mfd. Since 02/19) O PE R ATIONS OPERATIONS To. reduce. your. risk. of. serious. injury. or. damage. to. the. machine,. read. this. entire.manual.BEFORE.using.machine. Eye. injuries,. respiratory. problems,. or. hearing.loss.can.occur.while.operating. this. tool.....
Page 29 - Snipe
-27- Model W1864/W1865 (For Machines Mfd. Since 02/19) O PE R ATIONS Planing.Tips Cutting.Problems • Inspect your lumber for twisting or cupping, and surface one face on a jointer if necessary before planing workpiece. • Scrape off all glue when planing glued-up panels. Dried glue can quickly dull k...
Page 38 - ACCESSORIES
-36- Model W1864/W1865 (For Machines Mfd. Since 02/19) O PE R ATIO NS ACCESSORIES Planer.Accessories The following planer accessories may be available through your local Woodstock International Inc. Dealer. If you do not have a dealer in your area, these products are also available through online de...
Page 40 - MAINTENANCE; Schedule; Lubrication
-38- Model W1864/W1865 (For Machines Mfd. Since 02/19) M A INTE N A N CE MAINTENANCE Schedule For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. Note:. This maintenance schedule is based on average daily usage. Ad...
Page 41 - CE
-39- Model W1864/W1865 (For Machines Mfd. Since 02/19) M A INTEN A N CE Figure.40 . Table height chain and sprockets as viewed from underneath the base. Figure.38 . Location of column and leadscrew. Column Leadscrew Figure.39 . Example of table height worm gear housing. Worm Gear Housing Cap Screws ...
Page 43 - General
-41- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE RV IC E SERVICE General MAKE. SURE. that. your. machine. is. unplugged. during. all. service. proce- dures!. If. this. warning. is. ignored,. seri- ous.personal.injury.may.occur. This section covers the most common service adjustments or proc...
Page 44 - Alignment
-42- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE RV IC E 3. Remove front cabinet cover to access motor, as shown in Figure.45 . 4. If V-belts need to be replaced, raise motor to release belt tension (see Step.5 for instructions), roll belts off pulleys, then replace with a matched set of 3....
Page 45 - Heights
-43- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE RV IC E — If pulleys are parallel and in the same plane, no adjustment is necessary. Re-install belt cover. — If pulleys are not parallel or in the same plane, remove motor access panel, then proceed to Step.3 . 3. Loosen four motor mount bol...
Page 51 - Fingers
-49- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE RV IC E Calibrating.Table. Elevation.Scale Although correctly set at the factory, the table elevation scale can be adjusted for accuracy if necessary. To.calibrate.table.elevation.scale,.do.these.steps: 1.. Plane a scrap piece of stock until ...
Page 52 - Chain
-50- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE RV IC E Idler Sprocket Lock Bolts Figure.60.. Table height chain adjustment (shown without stand for purpose of illustration). Chain Tensioning.Table.Height. Chain The table height chain transfers movement from the elevation handwheel to the ...
Page 53 - Parallelism
-51- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE RV IC E Adjusting.Table. Parallelism Maximum.Allowable.Tolerances: Cutterhead/Table Side-to-Side ........................ 0.002" Head Casting/Table Front/Back ....................... 0.020" Table parallelism is critical to the operati...
Page 57 - WIRING DIAGRAM COLOR KEY
-55- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE RV IC E Electrical.Safety.Instructions SHOCK.HAZARD. Working on wiring that is connected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocut...
Page 58 - STOP; MOT
-56- Model W1864/W1865 (For Machines Mfd. Since 02/19) SE RV IC E This. motor. wiring. diagram. is. current. at. the. time. of. printing;. however,. always. use. the. diagram. on. the. inside. of. the. junction. box. cover. when. rewiring. your. motor! W1864.Wiring.Diagram STOP Read Page 55 Before W...
Page 62 - RT; PARTS; Main
-60- Model W1864/W1865 (For Machines Mfd. Since 02/19) PA RT S PARTS Main 1 2 96 20 19 22 25 24 19 30 52 53 36 25 16 40 25 43 13 13 12 12 69 216 217 215 111 115 48 50 32 35 39 48 49 49 49 33 34 18 49 51 601 606 615 506 506 603 604 51 108 112 112 44 14 38 38 38 56 15 79 81 114 97 82 55 507 86 (W1864)...
Page 75 - WARRANTY
WARRANTY Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, neglige...
