Shop Fox W1775 - Manual - manualsarea.com

Page 3 - Safety Instructions for Pneumatic Tools; SAFETY; For Your Own Safety Read Instruction Manual; NOTICE

Model W1775 Nailer/Stapler Kit -1- Safety Instructions for Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN. ...

Page 5 - Additional Safety for Nailers/Staplers

Model W1775 Nailer/Stapler Kit -3- 1. HAND INJURIES: Do not place your hands near the nail/staple point of entry. A nail/staple can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer/stapler to pressurized oxygen or ...

Page 6 - INTRODUCTION; Woodstock Technical

Model W1775 Nailer/Stapler Kit -4- No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other tools with caution and respect. Failure to do so could result in serious persona...

Page 7 - Compressed Air System

Model W1775 Nailer/Stapler Kit -5- The Model W1775 is designed to be operated at 60-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your new nailer/stapler, regulate the air pressure to find the optimum setting wi...

Page 8 - SETUP; Inventory

Model W1775 Nailer/Stapler Kit -6- SETUP Inventory Figure 2. Model W1775 inventory. This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Unpacking The following is a descrip...

Page 9 - Safety Nose Mechanism

Model W1775 Nailer/Stapler Kit -7- A safety mechanism on the nose of the nailer/stapler protects against accidental firing. When the trigger is pressed, the nailer/stapler will not fire until the safety nose mechanism is depressed. Before you use your nailer/stapler for the first time, check the saf...

Page 10 - OPERATIONS; Loading; Operating

Model W1775 Nailer/Stapler Kit -8- OPERATIONS Loading When replacing brad nails in your Model W1775, follow these guidelines: Gauge: 18Brad Length: 5 ⁄ 8 "-2" Staple Length: 5 ⁄ 8 "-1 5 ⁄ 8 " (crown 1 ⁄ 4 ") Capacity: 100 To load your nailer/stapler, do these steps: 1. DISCONNECT...

Page 12 - Clearing Jammed Nails

Model W1775 Nailer/Stapler Kit -10- A jammed nail or staple must be cleared before using the nailer/stapler again. To clear a jammed nail or staple from the magazine, do these steps: 1. DISCONNECT NAILER/STAPLER FROM THE AIR SUPPLY! 2. Unlock the catch lever and pull the magazine pusher back complet...

Page 13 - Replacing Piston and

Model W1775 Nailer/Stapler Kit -11- Replacing Piston and O-Rings Under heavy use, a piston or piston shaft may wear out. Replacement is quick and easy. Contact your authorized Shop Fox dealer to obtain the Piston Repair Kit (part number X1775001). To replace a piston and O-rings, do these steps: 1. ...

Page 14 - CLEANING & LUBRICATION; Cleaning

Model W1775 Nailer/Stapler Kit -12- CLEANING & LUBRICATION Cleaning Disconnect the nailer/stapler from the air supply before cleaning. Use a good solvent to clean the nose assembly of the nailer/stapler. Always be sure that the nailer/stapler is dry before using it again. Do not allow dust, chip...

Page 15 - PARTS BREAKDOWN

Model W1775 Nailer/Stapler Kit -13- PARTS BREAKDOWN � � � � � � � � � � �� ...

Page 16 - PARTS LIST

Model W1775 Nailer/Stapler Kit -14- PARTS LIST REF PART � # DESCRIPTION REF PART � # DESCRIPTION 1 X1775001 PISTON � REPAIR � KIT 44 X1775044 RETAINER � SNAP 2 X1775002 CARRYING � CASE 45 X1775045 STAND � PLATE 3 XPAW04M HEX � WRENCH � 4MM 46 XPEC12M E-CLIP � 12MM 4 XPAW03M HEX � WRENCH � 3MM 47 X17...

Page 17 - Troubleshooting; Symptom

Model W1775 Nailer/Stapler Kit -15- Troubleshooting Symptom Possible Cause Cause Possible Solution Air leaking at trigger valve area. 1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking between housing and hose 1. L...

Page 19 - Warranty Registration

CUT ALONG DOTTED LINE Name ___________________________________________________________________________________Street __________________________________________________________________________________City _________________________ State ___________________________ Zip ________________________Phone # ...

Shop Fox W1775 - Manual

Table of Contents:

Summary

Other Shop Fox Models