Page 2 - ii; IMPORTANT; • For your assistance in reporting the loss
ii IMPORTANT • For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. • Before recycling the packag ing, please ensure that you have checked the con-tents of the carton thorou...
Page 3 - iii
iii SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fi tted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face o...
Page 4 - iv
iv The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian, Dutch, Swedish, Portuguese, Korean, Chinese and Arabic. Carefully read through the operation instructions before operating the projector. Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Eng...
Page 5 - Introduction; ENGLISH; CONSUMER PRODUCT SAFETY ACT; See bottom of projector.
1 Intr oduction Before using the projector, please read this operation manual carefully. Introduction ENGLISH There are two important reasons for prompt warranty registration of your new SHARP Projec tor, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you i...
Page 6 - Caution Concerning Lamp Replacement; Caution
2 INFORMATION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Thi...
Page 7 - How to Read this Operation Manual; Info; For Future Reference; Maintenance
3 Intr oduction How to Read this Operation Manual The specifi cations are slightly different, depending on the model. However, you can connect and operate all models in the same manner. In this operation manual, the illustration and the screen display are simplifi ed for explanation, and may differ sl...
Page 8 - Contents; Preparing; Connecting the Projector to; Adjusting the Projected Image; Adjusting the Projector Function; Using
4 Contents Preparing Introduction How to Read this Operation Manual ......3 Contents .................................................4 IMPORTANT SAFEGUARDS ..................6How to Access the PDF Operation Manuals..............................................10 Accessories ...........................
Page 9 - Setting up the Projector Network; Appendix; Reference
5 Intr oduction System Lock Function ............................ 46Checking the Lamp Life Status ............... 47Keylock Function .................................... 48 Setting up the Projector Network Environment (“Network” Menu)..........49 Setting a Password ................................ 4...
Page 10 - IMPORTANT SAFEGUARDS
6 IMPORTANT SAFEGUARDS CAUTION: Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN...
Page 11 - Object and Liquid Entr y
7 Intr oduction 15. Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fi re or electric shock. 16. Object and Liquid Entr y Never push objects of any kind into this product through openings as they may touch dangerous voltag...
Page 13 - Caution regarding usage of the projector
9 Intr oduction Caution regarding usage of the projector If you are not to use the projector for a long time or before moving the projector, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it.Do not carr y the projector by holding the lens.Wh...
Page 14 - How to Access the PDF Operation Manuals; SETUP MANUAL
10 How to Access the PDF Operation Manuals PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to install Adobe ® Reader ® on your computer ( Windows ® or Macintosh ® ). Please download Adobe ® Reader ® from the Internet (http://www.adobe.com). A...
Page 15 - Accessories; Supplied accessories; Optional accessories
11 Intr oduction Accessories Supplied accessories Remote control <RRMCGA829WJSA> Two R-6 batteries (“A A” size, UM/SUM-3, HP-7 or similar) Power cord* RGB cable (10 ' (3.0 m)) <QCNWGA086WJPZ> For U.S. and Canada, etc. (6 ' (1.8 m)) <QACCDA007WJPZ> For Europe, except U.K. (6 ' (1.8 ...
Page 16 - Part Names and Functions; Numbers in; Projector; Top View; Front View
12 Part Names and Functions Numbers in Z refer to the main pages in this operation manual where the topic is explained. Projector 33 38, 51 26, 53 26, 53 38 26 29 38 29 53 38 32 28 Top View STANDBY/ON button For turning the power on and putting the projector into Standby mode. Lamp indicator Tempera...
Page 17 - Rear View; Terminals
13 Intr oduction Numbers in Z refer to the main pages in this operation manual where the topic is explained. Rear View Using the Kensington Lock This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with t...
Page 19 - Inserting the Batteries; Pull down the tab on the cover and remove the; Insert the lower tab of the cover into the opening,; Usable Range; When using the remote control
15 Intr oduction Inserting the Batteries 1 Pull down the tab on the cover and remove the cover towards the direction of the arrow. 2 Insert the batteries. Inser t the batteries making sure the polarities correctly match the m and n marks inside the batter y compar tment. 3 Insert the lower tab of th...
Page 20 - Quick Start; Setup and Projection; Place the projector facing a wall or a screen
16 Quick Start This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step. Setup and Projection In this section, connection of the projector and the computer is explained using one example. INPUT buttons 6 STANDBY button 8...
Page 21 - Adjust the projected image; COMPUTER; Select the Input mode; Turn the power off
17 Quick Start 1 Adjusting the focus. 2 Adjusting the height. 3 Adjusting the picture size. 4. Adjust the projected image B P. 27 Correcting trapezoidal distor tion using Keystone Correction. On the projector On the remote control Shrinks upper side. Shrinks lower side. 5. Correct trapezoidal distor...
Page 22 - Setting up the Projector; Video Setup; Example of standard setup; Side View
18 Setting up the Projector Video Setup If using this projector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See page 44 .) Setting up the Projector For optimal image quality, position the projector perpendicular to the screen with the projector's feet fl at and level. Doing ...
Page 23 - Setup; Indication of the Projection Image Size and Projection Distance
19 Setup Projection (PRJ) Mode The projector can use any of the 4 projection modes shown in the diagram below. Select the mode most appropriate for the projection setting in use. ( You can set the PRJ mode in “SCR-ADJ” menu. See page 44 .) Table mounted, front projection [Menu item ➞ “Front”] Table ...
Page 24 - Screen Size and Projection Distance
20 Setting up the Projector (Continued) Screen Size and Projection Distance 4:3 Signal Input (Normal Mode) Picture (Screen) size Projection distance [L] Distance from the lens center to the bottom of the image [H] Diag. [ Ȥ ] Width Height Minimum [L1] Maximum [L2] 500 " (1270 cm) 1016 cm (400 &#...
Page 25 - Connections; Connecting the Projector to Other Equipment; Terminals on the Projector
21 Connections Connecting the Projector to Other Equipment Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the equipment to be connected. After making all connections, turn on the projector and then the other pieces of equipment. When conne...
Page 26 - Connecting the Projector to Other Equipment (Continued)
22 Connecting the Projector to Other Equipment (Continued) Equipment Terminal on connected equipment Cable Terminal on the projector Video equipment HDMI output terminal HDMI to DVI cable (commercially available) DVI-I DVI digital output terminal DVI Digital cable (commercially available) Component ...
Page 28 - Controlling the Projector by a Computer
24 Controlling the Projector by a Computer When the RS-232C terminal on the projector is connected to a computer with an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. Refer to the “SETUP MAN...
Page 29 - When connecting to the LAN terminal using a LAN cable; Connecting the Power Cord
25 Connections When connecting to the LAN terminal using a LAN cable T X /RX LED (yellow)Illuminates when transmitting/receiving data. LINK LED (green)Illuminates when linked. * To ensure safety, do not connect the L AN terminal with any cables that may cause excessive voltage such as a telephone li...
Page 30 - Turning the Projector On/Off; Turning the Projector On
26 Turning the Projector On/Off Turning the Projector On Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 21 to 25 .) Open the lens shutter fully and press STANDBY/ON on the projector or ON on the remote contro...
Page 31 - Image Projection; Lift the projector to adjust its; Adjusting the Picture Size
27 Basic Operation Image Projection Adjusting the Projected Image 1 Adjusting the Focus You can adjust the focus with the focus ring on the projector. Rotate the focus ring to adjust the focus while watching the projected image. 2 Adjusting the Height The height of the projector can be adjusted usin...
Page 32 - KEYSTONE
28 Image Projection (Continued) Correcting Trapezoidal Distortion When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. The Keysto...
Page 33 - Switching the Input Mode; Adjusting the Volume; Displaying the Black Screen
29 Basic Operation Switching the Input Mode Select the appropriate Input mode for the connected equipment. Press COMPUTER , DVI , S -VIDEO or VIDEO on the remote control to select the Input mode. When you press INPUT on the projector or DVI on the remote control, the INPUT list appears.Press P / R t...
Page 34 - Resize Mode
30 Image Projection (Continued) Resize Mode This function allows you to modify or customize the Resize mode to enhance the input image. Depending on the input signal, you can choose a desired image. Press RESIZE . See page 43 for setting on menu screen. COMPUTER Main resolution NORMAL FULL DOT BY DO...
Page 35 - About Copyrights
31 Basic Operation VIDEO/DTV Input signal For 4:3 screen For 16:9 screen Video/DT V Image t ype NORMAL ARE A ZOOM V-STRETCH BORDER STRETCH 4 8 0 I , 480P, 576 I , 576P, NTSC, PAL , SECAM 4:3 aspect ratio *1 *1 Squeeze *1 *1 Letter box *1 *1 720P, 1035 I , 10 8 0 I , 1080P 16:9 aspect ratio *1 —*2 —*...
Page 36 - Operating with the Remote Control; Displaying the Pointer; Using the Spot Function
32 Operating with the Remote Control POINTER button ECO+QUIET button Adjustment buttons ( P / R / O / Q ) BREAK TIMER button SPOT button AUTO SYNC button FREEZE button PICTURE MODE button MAGNIF Y buttons EFFECT button Displaying and Setting the Break Timer 1 Press BREAK TIMER . The timer star ts to...
Page 37 - Freezing a Moving Image
33 Useful Featur es Auto Sync(Auto Sync Adjustment) Auto Sync function works when detecting input signal after the projector turns on. Press AUTO SYNC to manually adjust with Auto Sync function. When the optimum image cannot be achieved with Auto Sync adjustment, use the help menu for manual adjustm...
Page 38 - Using the Remote Control as the Wireless Computer Mouse; Connecting with a USB cable; When moving the cursor; Operating with the Remote Control (Continued)
34 Using the Remote Control as the Wireless Computer Mouse When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse. If the computer is placed too far away from the projector to be connected via the USB cable, the remote receiver (optional...
Page 39 - Menu Items; The following shows the items that can be set in the projector.
35 Useful Featur es Menu Items The following shows the items that can be set in the projector. “Picture” menu Main menu Sub menu Picture Page 40 Page 40 Page 41 Page 41 Page 41 Page 41 Page 41 Page 42 Page 42 +30 -30 Contrast +30 -30 +30 -30 +30 -30 1 -1 2 0 +30 -30 +30 -30 +30 -30 Tint Color Sharp ...
Page 41 - “Network” menu
37 Useful Featur es “Network” menu SEL./ADJ. ENTER END Pict. SCR PRJ Network Help Password Disable DHCP Client Off TCP/IP MAC Address Projector X X : X X : X X : X X : X X : X X X X - X X X X “Help” menu SEL ENTER END There is no picture or audio Vertical stripes or flickering image appear Data image...
Page 44 - Selecting the Picture Mode
40 Picture Adjustment (“Picture” Menu) Menu operation n Page 38 Q PAGE1 Q PAGE2 Picture Mode Contrast 0 0 0 0 Bright Color Tint 0 Sharp Standard SEL./ADJ. ENTER END 0 0 Red Blue Picture SCR PRJ Net. Help 1 2 Picture Mode CLR Temp B r i l l i a n t C o l o r T M C.M.S. Setting C.M.S. Standard SEL./AD...
Page 45 - Adjusting the Image; Adjusting the Color; Adjusting the Colors
41 Useful Featur es Menu operation n Page 38 2 Adjusting the Image Adjustment items O button Q button Contrast For less contrast. For more contrast. Bright For less brightness. For more brightness. Color* 1 For less color intensity. For more color intensity. Tint* 1 For making skin tones purplish. F...
Page 46 - Progressive
42 5 Progressive Selectable items Description 2DProgressive Useful to display fast-moving images such as spor ts. 3D Progressive Useful to display relatively slow-moving images such as drama and documentar y more clearly. Film Mode Reproduces the image of fi lm source* clearly. Displays the optimized...
Page 50 - Setting/Changing the keycode; Select “System Lock”, then press
46 6 Audio Output Type Setting This function determines whether the audio level output from the AUDIO output (MONITOR output) terminal is fi xed or variable by linking with VOLUME. Selectable items Description FAO(Fixed AudioOutput) Audio output that does not var y instrength with the volume level of...
Page 51 - Press the 4 buttons on the remote; Checking the Lamp
47 Useful Featur es 3 Press the 4 buttons on the remote control or on the projector to enter the preset keycode in “Old Code”. When setting the keycode for the fi rst time, press R on the projector for four times. Setting the System Lock PRJ - ADJ Old Code New Code Reconfirm – – – – – – – – – – – – If...
Page 52 - Keylock Function; Locking the Operation Buttons; Taking the Keylock off
48 Keylock Function Locking the Operation Buttons on the Projector Use this function to lock the operation buttons on the projector. Locking the Operation Buttons Hold down ENTER on the projector for about 5 seconds while the projector is being turned on. On-screen display The Keylock function does ...
Page 53 - Setting up the Projector Network Environment (“Network” Menu); Setting a Password; Changing the Password; If you forget the password
49 Useful Featur es Setting up the Projector Network Environment (“Network” Menu) Menu operation n Page 38 SEL./ADJ. ENTER END Pict. SCR PRJ Network Help Password Disable DHCP Client Off TCP/IP MAC Address Projector X X : X X : X X : X X : X X : X X X X - X X X X 4 2 3 1 1 Setting a Password If you ...
Page 54 - DHCP Client Setting; Confi rming the
50 2 DHCP Client Setting Connect the L AN cable before turning the projector on. If not, the DHCP Client function does not work. Selectable items Description On Obtains confi guration parameters for TCP/IP network automatically. Of f Sets the TCP/IP manually. Select “On” for “DHCP Client”. “Obtaining...
Page 55 - Troubleshooting with the “Help” Menu
51 Useful Featur es Utilizing the “Help” Menu Functions Example: When image fl ickering appears Operation to solve image fl ickering when projecting the computer RGB signal. 1 Press MENU/HELP . 2 Press O or Q to select “Help”, then press ENTER . 3 Press P or R to select “Vertical stripes or fl ickering...
Page 57 - Maintenance Indicators
53 Appendix Maintenance Indicators The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector.If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector...
Page 59 - Regarding the Lamp; Lamp
55 Appendix Regarding the Lamp Lamp It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a signifi cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (S...
Page 61 - Resetting the Lamp Timer
57 Appendix 4 Remove the lamp unit. Loosen the securing screws from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. 5 Insert the new lamp unit. Press the lamp unit fi rmly into the lamp unit compar tment. Fa...
Page 62 - Computer Compatibility Chart; DTV
58 Computer Compatibility Chart Computer • Multiple signal suppor t Horizontal Frequency: 15-110 kHz, Ver tical Frequency: 45-85 Hz, Pixel Clock: 12-170 MHz Sync signal: Compatible with T TL level • Compatible with sync on green signal PC/MAC Mode Resolution Horizontal frequency [kHz] Ver tical freq...
Page 63 - Troubleshooting
59 Appendix Troubleshooting Problem Check Page No picture and no sound or projector does not star t. Projector power cord is not plugged into the wall outlet. • 25 Power to the external connected devices is of f. • – The lens shutter is closed. • 26, 29 The selected Input mode is wrong. • 29 Cables ...
Page 65 - For SHARP Assistance
61 Appendix U.S.A. Sharp Electronics Corporation 1-888-GO-SHARP (1-888-467-4277) [email protected] http://www.sharpusa.com Canada Sharp Electronics of Canada Ltd. (905) 568-7140 http://www.sharp.ca Mexico Sharp Electronics Corporation Mexico Branch (525) 716-9000 http://www.sharp.com.mx Latin ...
Page 66 - Specifi cations; This SHARP projector uses a DLP
62 Specifi cations Model PG-D50X3D PG-D45X3D Display devices 0.7" DLP ® Chip Resolution XGA (1024 × 768) Lens F number F 2.5 – 2.7 Zoom Manual, ×1.15 (f = 21.0 – 24.2 mm) Focus Manual Input terminals DVI-I (Compatible with HDCP) ×1 Computer/Component(mini D-sub 15 pin) ×1 S-Video (mini DIN 4 pin)...
Page 67 - Dimensions
63 Appendix Dimensions Units: inches (mm) M4 M4 M4 M4 1 / 4 (6) 13 13 / 64 (335) 3 15 / 16 (100) 1 43 / 64 (42.2) 4 17 / 32 (115) 3 23 / 64 (85) 4 17 / 32 (115) 15 3 / 4 (400) 1 / 8 (3) 1 1 / 2 (38) 3 33 / 64 (89) 6 49 / 64 (171.5) 15 / 64 (5.75) 1 13 / 16 (45.75) 4 5 / 8 (116.25) 2 61 / 64 (75) 7 5...
Page 68 - Index
64 3D MODE button ······················································· 14 Accessories ······························································· 11AC socket ·································································· 25Adjustment buttons ···············································...
