Page 2 - Revision history; Revision
Revision history Copyright © 2007 Seagate Technology LLC. All rights reserved. Printed in U.S.A.Publication number: 100441946, Rev. E June 2007Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Lyrion Series,...
Page 3 - Contents
Lyrion Series IDE Product Manual, Rev. E i Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 4 - ii
Page 5 - iii; List of Figures
Lyrion Series IDE Product Manual, Rev. E iii List of Figures Figure 1. Lyrion Series (IDE interface) disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. Typical 3.3V startup and operation current profile . . . . . . . . . . . . . . . . . . . . ....
Page 6 - iv
Page 7 - Introduction; Lyrion
Lyrion Series IDE Product Manual, Rev. E 1 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Lyrion Series ® IDE drives: • ST760211DE-60GB, ST730212DE-30GB disc drives with an IDE interface. These drives provide the following k...
Page 8 - Disclaimer; Seagate Technology LLC; Drive care
2 Lyrion Series IDE Product Manual, Rev. E 1.1 Disclaimer Seagate Technology LLC makes no warranties whatsoever, including any warranty of merchantability, non- infringement, fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specification or sample. Seagate m...
Page 9 - Drive specifications; the drive; Overview; definition, see the appropriate section of this manual.; Specifications; Drive specification
Lyrion Series IDE Product Manual, Rev. E 3 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST760211DE and ST730212D...
Page 10 - Formatted capacity; LBA mode addressing; where; Default logical geometry
4 Lyrion Series IDE Product Manual, Rev. E 2.2 Formatted capacity LBA mode addressing When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above . 2.3 Default logical geometry Temperature gradi...
Page 11 - Technology
Lyrion Series IDE Product Manual, Rev. E 5 2.4 Recording and interface technology 2.5 Physical characteristics 2.6 Time to ready Technology Specification Interface IDE (Parallel ATA) Recording method Perpendicular Magnetic Recording Recording density BPI (bits/inch average) 1,025,000 Track density T...
Page 12 - Power specifications
6 Lyrion Series IDE Product Manual, Rev. E 2.7 Power specifications The drive receives DC power (+3.3V) through the ZIF connector (IDE interface). 2.7.1 Power consumption Power requirements for the drives are listed in the table on page 7. Typical power measurements are based on an average of drives...
Page 13 - Typical current profile; Typical 3.3V startup and operation current profile; DC power; Power Consumption at 3.3V; Read
Lyrion Series IDE Product Manual, Rev. E 7 * Maximum is the average of the peak value in 10 msec window 2.7.1.1 Typical current profile Figure 2. Typical 3.3V startup and operation current profile Table 2: DC power Power Consumption at 3.3V Average (W) Startup (max*) 1.15 Read 1.0 Write 0.9 Performa...
Page 14 - Conducted noise; injected noise at up to 20 MHz.; Voltage tolerance
8 Lyrion Series IDE Product Manual, Rev. E 2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +3.3 volt line. Using 3.3-volt power, the drive is expected to operate with a maximum of 70 mV peak-to-peak square-wave in...
Page 16 - Environmental specifications
10 Lyrion Series IDE Product Manual, Rev. E 2.8 Environmental specifications 2.8.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 70°C (158°F) within the operating ambient con...
Page 17 - Shock; Drive axis definition for Lyrion Series drives; Operating shock
Lyrion Series IDE Product Manual, Rev. E 11 2.8.5 Shock All shock measurements in this section are carried out at drive level. For all linear shock test, operating or nonoperating, the input shock level is measured at the frame of the drive at the specific location as indicated in Figure 3 below. Fi...
Page 18 - Gs RMS. The drive operates without a hard error while being; Nonoperating sweep sine vibration; Hz to 10 Hz
12 Lyrion Series IDE Product Manual, Rev. E 2.8.6.1 Operating sweep sine vibration The following lists the maximum operating sweep sine vibration levels that the drive may experience while meeting the performance standards specified. It consists of a forward and backward sweep from 10 Hz to 500 Hz t...
Page 20 - Drive level acoustics
14 Lyrion Series IDE Product Manual, Rev. E 2.9 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). Discrete tone penalties are added to the A-weighted sound power (LW) with the following formula only when determin-ing compliance: LWt(spec) == LW...
Page 21 - Reliability; Measurement type; Nonrecoverable read errors
Lyrion Series IDE Product Manual, Rev. E 15 2.11 Reliability Measurement type Specification Nonrecoverable read errors 1 per 10 14 bits read, max. Load/Unload (LUL) cycles 300,000 software-controlled 20,000 power loss Power On Hours (POH) per year 500 hours Warranty Per agreement
Page 22 - Agency certification; Safety certification; Lyrion Series
16 Lyrion Series IDE Product Manual, Rev. E 2.12 Agency certification 2.12.1 Safety certification The drives are recognized in accordance with UL60950-1, CAN/CSA-C22.2 No.60950-1, EN60950 and IEC 60950. 2.12.2 Electromagnetic compatibility Hard drives that display the CE mark comply with the Europea...
Page 23 - 表示该部件(于同类物品程度上)所含的危险和有毒物质低于中国
Lyrion Series IDE Product Manual, Rev. E 17 2.12.4 China Restriction of Hazardous Substances (RoHS) Directive This product has an Environmental Protection Use Period (EPUP) of 20 years. The following table contains information mandated by China's "Marking Requirements for Control of Pollution Ca...
Page 24 - . This booklet is available from the Super-
18 Lyrion Series IDE Product Manual, Rev. E If necessary, you should consult your dealer or an experienced radio/television technician for additional sug-gestions. You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Televisi...
Page 25 - Configuring and mounting the drive; Handling and static discharge precautions; Lyrion Series breather hole location
Lyrion Series IDE Product Manual, Rev. E 19 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to pot...
Page 26 - immediately after operation.
20 Lyrion Series IDE Product Manual, Rev. E • Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamin...
Page 27 - Drive installation; See Figure 7 for drive mechanical dimensions.
Lyrion Series IDE Product Manual, Rev. E 21 3.2 Drive installation See Figure 7 for drive mechanical dimensions. Follow these installation precautions when inserting the drive:• Follow instructions for the installation of data storage devices, provided with your device’s user manual.• Do not obstruc...
Page 28 - Lyrion Series FPC dimensions; Mounting considerations; where the mounting material can rest for mounting.
22 Lyrion Series IDE Product Manual, Rev. E Figure 8. Lyrion Series FPC dimensions 3.3 Mounting considerations • Use an elastic mounting material to protect drives so as to ensure that more shock can be absorbed.• There are guides along the side for mounting. Refer to figure on areas (refer to Figur...
Page 29 - Interface description; Connector interface signals and connector pins
Lyrion Series IDE Product Manual, Rev. E 23 4.0 Interface description The drives use the industry-standard ATA (IDE) interface. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–4. 4.1 Connector interface signals and connector pins The following ...
Page 31 - Supported ATA commands; Supported commands; Command Name
Lyrion Series IDE Product Manual, Rev. E 25 4.2 Supported ATA commands The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA commands, refer to ATA version 7 specification, Volume 1. (www.t13.org) Table 9: Supported commands Command Name Comma...
Page 32 - Write DMA
26 Lyrion Series IDE Product Manual, Rev. E Table 9: Supported commands Write DMA CAh DMA data-out Standby Immediate E0h Non data Idle Immediate E1h Non data Standby E2h Non data Idle E3h Non data Read Buffer E4h PIO data-in Check Power Mode E5h Non data Sleep E6h Non data Flush Cache E7h Non data W...
Page 33 - Identify Device command; The Identify Device command (command code EC; Word
Lyrion Series IDE Product Manual, Rev. E 27 4.2.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte (256 word) block of data, whose contents are as shown in the fol...
Page 35 - Feature Description
Lyrion Series IDE Product Manual, Rev. E 29 4.2.2 Set Features command This command is used by the host to establish parameters that affect the execution of certain drive features. The supported features determined by the value in the Features register are as shown in Table 11. Read look-ahead and w...
Page 37 - Seagate Technology support services; Internet; mySeagate; Seagate Service Centers; Presales Support; SeaTDD
Lyrion Series IDE Product Manual, Rev. E 31 5.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com . Worldwide support is available 24 hours daily by email for your questions. Presales Support: [email protected] Technical Su...
Page 38 - Customer Service Operations; Warranty Service; USA/Canada/Latin America support services; Direct dial; and Mexico; Europe, the Middle East and Africa Support Services
32 Lyrion Series IDE Product Manual, Rev. E Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-re...
Page 39 - Publication feedback survey; Thank you for your time and comments.
Lyrion Series IDE Product Manual, Rev. E 33 Publication feedback survey We are interested in your comments and suggestions regarding this publication. Please take a few minutes to participate in our survey at the following URL: http://survey.seagate.com/survey/techpubs.nsf Thank you for your time an...
Page 41 - Index
Lyrion Series IDE Product Manual, Rev. E 35 Index A acoustics 14 Active mode 9 agency certification (regulatory) 16 altitude 10 ambient conditions 3 ambient temperature 10 areal density 1 , 5 ATA-standard commands 25 Australian C-Tick 16 B BPI 5 buffer 1 , 5 C cache 1 , 5 case temperature 10 CE mark...
