Page 2 - Document Revision History; Revision
© 2014 Seagate Technology LLC. All rights reserved. Publication number: 100743737, Rev. C October 2014 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/orother countries. Seagate Archive HDD and SeaTools are either trademarks ...
Page 3 - Contents; Seagate
Seagate Archive HDD Product Manual, Rev. C i Contents Seagate ® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 5 - Figures; Figure 1
Seagate Archive HDD Product Manual, Rev. C iii Figures Figure 1 Typical 5TB model 5V - 6Gb/s startup and operation current profile . . . . . . . . . . . . . . . . . . . 8 Figure 2 Typical 5TB model 12V - 6Gb/s startup and operation current profile . . . . . . . . . . . . . . . . . . 8 Figure 3 Attac...
Page 7 - About the SATA interface; or other configuration options.; Standard; Note
Seagate Archive HDD Product Manual, Rev. C 2 www.seagate.com 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following: Seagate ® Archive HDD model drives:. These drives provide the following key features:• 5900 RPM spindle speed.• TGMR recordin...
Page 8 - Drive Specifications; the drive; Specification summary tables; The specifications listed in; Table 1
Seagate Archive HDD Product Manual, Rev. C 3 www.seagate.com 2.0 Drive Specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power.For convenience, the phrases the drive and this drive are used throughout this manual to indicate the fol...
Page 10 - Formatted capacity; LBA mode; where; Recording and interface technology; Model
Seagate Archive HDD Product Manual, Rev. C 5 www.seagate.com 2.2 Formatted capacity *One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.2.1 LBA mode When addressing...
Page 11 - Seek time; Read
Seagate Archive HDD Product Manual, Rev. C 6 www.seagate.com 2.5 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured usingdrive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average...
Page 12 - • Spinup power; Typical DC - average of average operating currents; • Average Idle Current; a random track location.; DC power requirements
Seagate Archive HDD Product Manual, Rev. C 7 www.seagate.com * During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. • Spinup power Spinup power is measured from the time of power-on to th...
Page 13 - TB model current profile
Seagate Archive HDD Product Manual, Rev. C 8 www.seagate.com 2.7.1.1 Typical current profiles 5TB model current profile Figure 1 Typical 5TB model 5V - 6Gb/s startup and operation current profile Figure 2 Typical 5TB model 12V - 6Gb/s startup and operation current profile
Page 14 - Conducted noise; injected noise at up to 10MHz.; Voltage tolerance; mounting
Seagate Archive HDD Product Manual, Rev. C 9 www.seagate.com 2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the+12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. • Using 12-volt power, the driv...
Page 15 - Altitude; Operating shock; repeated more than two times per second.; Vibration; Operating vibration
Seagate Archive HDD Product Manual, Rev. C 10 www.seagate.com 2.8.4 Altitude 2.8.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drivemounting screws. Shock may be applied in the X, Y or Z axis. 2.8.5.1 Operating shock These drives compl...
Page 16 - Acoustics; Electromagnetic immunity; Performance Seek; Table 4; Test
Seagate Archive HDD Product Manual, Rev. C 11 www.seagate.com 2.9 Acoustics D r i v e a c o u s t i c s a re m e a s u re d a s o v e r a l l A - w e i g h t e d a c o u s t i c s o u n d p o w e r l e v e l s ( n o p u re t o n e s ) . A l lmeasurements are consistent with ISO document 7779. Sound ...
Page 17 - Reliability; Section 2.8 Environmental specifications; Agency certification
Seagate Archive HDD Product Manual, Rev. C 12 www.seagate.com 2.12 Reliability 2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF) The product shall achieve an Annualized Failure Rate (AFR) of <1% (MTBF of 800K hours) when operated at annominal power and typical case tempera...
Page 18 - Korean RRL; FCC verification; Radio and television interference.; How to Identify and
Seagate Archive HDD Product Manual, Rev. C 13 www.seagate.com Korean RRL If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC)Framework r...
Page 19 - Environmental protection
Seagate Archive HDD Product Manual, Rev. C 14 www.seagate.com 2.14 Environmental protection Seagate designs its products to meet environmental protection requirements worldwide, including regulationsrestricting certain chemical substances. 2.14.1 European Union Restriction of Hazardous Substances (R...
Page 20 - Configuring and Mounting the Drive; Handling and static-discharge precautions; Table 5; Figure 3 Attaching SATA cabling
Seagate Archive HDD Product Manual, Rev. C 15 www.seagate.com 3.0 Configuring and Mounting the Drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpacking, and before installation, the drive may...
Page 21 - Drive mounting; Figure 4; Figure 4 Mounting dimensions
Seagate Archive HDD Product Manual, Rev. C 16 www.seagate.com 3.4 Drive mounting Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in thebottom-mounting holes. Refer to Figure 4 for drive mounting dimensions. Follow these important mounting prec...
Page 22 - Data Encryption; Section 4.5 Data Bands; Controlled Access; Admin SP; Section 4.4 Drive Locking; Locking SP
Seagate Archive HDD Product Manual, Rev. C 17 www.seagate.com 4.0 About (SED) Self-Encrypting Drives Self-encrypting drives (SEDs) offer encryption and security services for the protection of stored data, commonly known as"protection of data at rest." These drives are compliant with the Trus...
Page 23 - Default password; Drive Locking; Data Bands; Cryptographic Erase
Seagate Archive HDD Product Manual, Rev. C 18 www.seagate.com 4.2.3 Default password When the drive is shipped from the factory, all passwords are set to the value of MSID. This 32-byte random value can only beread by the host electronically over the interface. After receipt of the drive, it is the ...
Page 24 - Power Requirements; Supported Commands; RevertSP
Seagate Archive HDD Product Manual, Rev. C 19 www.seagate.com 4.6 Cryptographic Erase A significant feature of SEDs is the ability to perform a cryptographic erase. This involves the host telling the drive to changethe data encryption key for a particular band. Once changed, the data is no longer re...
Page 25 - Hot-Plug compatibility; Notes; • All used voltage pins (V; Caution
Seagate Archive HDD Product Manual, Rev. C 20 www.seagate.com 5.0 SATA Interface These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supportsATA programmed input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6.For ...
Page 26 - Supported ATA commands; Table 6; Command name
Seagate Archive HDD Product Manual, Rev. C 21 www.seagate.com 5.3 Supported ATA commands The following table lists SATA standard commands that the drive supports.For a detailed description of the ATA commands, refer to the Serial ATA International Organization:Serial ATA Revision 3.0 ( http://www.sa...
Page 28 - Table 7; Word
Seagate Archive HDD Product Manual, Rev. C 23 www.seagate.com 5.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in on ...
Page 30 - Bit
Seagate Archive HDD Product Manual, Rev. C 25 www.seagate.com 95–99 ATA-reserved 0000 H 100–103 Total number of user-addressable LBA sectors available (see Section 2.2 for related information). These words are required for drives that support the 48-bit addressing feature. Maximum value: 0000FFFFFFF...
Page 33 - Draft; Code in features register
Seagate Archive HDD Product Manual, Rev. C 28 www.seagate.com 5.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitorspredetermined drive attributes that are susceptible to degradation over time. If self-monitoring det...
Page 34 - Seagate Technology LLC
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888EUROPE, MIDDLE EAST AND AFRICA Sea...
