Schweigen UM1390-9SEL - User Manual

Page 2 - Welcome

Page 2 Welcome Thank you for purchasing your new Schweigen Endline Isodrive system. To get the maximum output from the Isodrive 1350 motor, please read through this guide before use and installation. This guide contains important information on the correct use and maintenance of the unit, as well as...

Page 3 - Index; Motor Installation

Page 3 Index 1. Welcome _____________________________________________________________________________________2 2. Your Safety Receiving your Isodrive Motor ____________________________________________________________________ 4 Before Installation _____________________________________________________...

Page 4 - Before Installation; Please see our website; Electrical Cord; MUST BE; installed in such a way that access is easy; RECEIVING YOUR ISODRIVE MOTOR; Any damage or defects MUST be reported

Page 4 2. Your Safety This appliance is not intended for use by person/s (including children) with reduced physical, sensory or mental capabilities, or lack of experience and/or knowledge. Unless the person has been given supervision or instruction concerning the use of the appliance by a person res...

Page 5 - Fan module and dual foil flexi-duct are; Recommended Ducting

Page 5 2. Your Safety This guide is for the installation of the Isodrive motor system after the rangehood has been mounted. (Refer to rangehood installation manual on how to install the rangehood). NOTE: All flexi ducting measurements are referring to inside measurements, unless otherwise mentioned....

Page 6 - Do not use with a timer.

Page 6 Minimum Mounting Height This fan unit is intended for mounting at a minimum height of 2.1 metres (measured to the lower part of the fan impeller) above a floor or the ground. Avoidance of Back Flow Care should be taken to avoid the back flow of gases into the room from the open flue of gas or...

Page 7 - Endline Isodrive System 1350; Approx. 5 metre, 10amp cable and standard male plug; Dimensions

Page 7 3. Description Endline Isodrive System 1350 Included in the box: 1. Isodrive 1350 motor + housing Approx. 5 metre, 10amp cable and standard male plug 2. Flexible ducting Approx. 6 metres, 200mm (210mm OD 1 ) diameter 3. Bell-mouth adopter ring 200mm4. Back Draught Shutter Not included in the ...

Page 8 - Wall Installation; Installation Overview

Page 8 4. Installation Wall Installation 1. Remove the Endline Isodrive 1350 Motor System from the packaging. 2. Undo the 2 screws holding front grille and the deflector, and remove them from housing (See figure 1A, pg.10). 3. Remove the foam packaging material that is behind the grille. 4. Remove t...

Page 10 - Full Body Assembly Cross Section

Page 10 5. Installation Grille Housing attachmen t scr ews De flect or Comple tely seal the join t be tw een out er flange and w all t o pr ev en t w at er ingr ess in to building. Seal the full perime ter using pr emium quality bonding ur ethane. Base o f housing has a one degr ee do wn w ar ds slo...

Page 11 - Removal of Motor Assembly

Page 11 5. Installation Insert electrical plug fully into mounted power outlet inside housing Figure 2 Figure 1B TO REMOVE: Slide removable assembly along side rails lifting the motor mounting bracket side flanges up and over the locating stops. Fan and shutter assembly Motor mounting bracket Stop E...

Page 12 - Wall Cut Out

Page 12 Building wall shown Wall Aperture Cut Out 40 mm (minimum) 340 - 345mm (horiz ontal) 265- 270mm (v ertical) 5. Installation Support body at vertical walls if possible to ensure forward slope draining Wall Wall Completely seal front flange to wall joint using high quality bonding urethane all ...

Page 14 - Attaching optional fire ember Mesh Guard

Page 14 Guard is attached by screwing through both sides of guard into existing grille. 45mm deep Mesh Motor housing Normal grille Fire guard frame Fire guard frame 20mm deep 5. Installation (optional) Figure 7 Can be fitted to any installation with access to the front. Attaching optional fire ember...

Page 15 - Flexible Ducting Installation; Flexible Ducting; A list of preferred Schweigen installers can be; Shallow Space

Page 15 6. Flexible Ducting Installation Flexible Ducting Flexible ducting must be fully extended and cut to the required length upon installation. Maximum fan performance will not be achieved unless the ducting is fully extended. Failure to fully extend ducting results in a smaller air passage and ...

Page 16 - Figure 14 Examples of securing ducting; Option 1

Page 16 6. Flexible Ducting Installation Securing Flexible Duct (Example) Flexible duct must be installed with supports at maximum intervals of 1.0 metres. Flexible ductwork can be supported by using good quality aluminium foil tape. Provided that it does not restrict the internal diameter of the du...

Page 17 - Parts List for Isodrive Motor 1350; Part Number; Optional

Page 17 7. Parts List Parts List for Isodrive Motor 1350 EL RMB build assy (Optional) EL Inlet Build Assy P3013 P3012 200mm Boss Build Assy EL Base Build Assy P3036 P3024 (Optional) P3011 (Optional) Part Number Description Quantity P3036 Eliso1350 - Vinidex: 150mm x 50mm Pipe 1 P3024 Eliso1350 - Fir...

Page 18 - Figure 15 Avoid chemical contact to motor system; Specifications

Page 18 8. Maintenance / Specifications / Warranty Information Restoration or Cleaning Before doing your wall restoration or cleaning, please completely cover the outside motor system and avoid all chemical contact. IMPORANT Any damages caused by the use of chemical products are not covered by warra...

Page 19 - Notes

Schweigen UM1390-9SEL - User Manual

Table of Contents:

Summary

Other Schweigen Range Hoods Models