Page 2 - Welcome
Page 2 Welcome Thank you for purchasing your new Schweigen Isodrive system. To get the maximum output from this unit, please read through this guide before use and installation. This guide contains important information on the correct use and maintenance of the unit, as well as important safety note...
Page 3 - Index
Page 3 Index 1. Welcome _____________________________________________________________________________________2 2. Your Safety Receiving your rangehood ______________________________________________________________________ 4 Before Installation ________________________________________________________...
Page 4 - Before Installation; Electrical Cord; RECEIVING YOUR RANGEHOOD
Page 4 2. Your Safety This appliance is not intended for use by person/s (including children) with reduced physical, sensory or mental capabilities, or lack of experience and/or knowledge. Unless the person has been given supervision or instruction concerning the use of the appliance by a person res...
Page 5 - Recommended Installation Distance
Page 5 2. Your Safety This guide is for the installation of the motor used in the Isodrive systems after the canopy/rangehood or bathroom extraction grill has been mounted on the wall or ceiling. (Refer to canopy/rangehood or bathroom extraction unit installation manual). NOTE: All PVC pipe and Stee...
Page 7 - Isodrive Motor; NOTE
Page 7 3. Description Isodrive Motor Included in the box: 1. Isodrive 900 motor (280W x 200H mm approx.) Approx. 3 metre, 10amp cable and standard plug 2. Fire resistant 150mm (160mm outside dimension) PVC riser pipe 3. SteelFlex ™ safety ducting. Approx. 4 metres, 200mm (210mm outside dimension) di...
Page 8 - Roof Installation
Page 8 4. Installation Roof Installation Recommended duct length: 900 motor — minimum 4 metres. Mount 150mm (ISD) rigid PVC pipe securely to beams, trusses or other appropriate structures: refer figure 1. The pipe should be mounted vertically with the roof penetration being sealed using a Dektite or...
Page 9 - IMPORTANT
Page 9 4. Installation 900 motor Figure 1: Roof mount option IMPORTANT For more SteelFlex ™ ducting instructions, refer page 16. Pipe protrusion above dektite Fix fan module using side locking screw Connect to rangehood Connect to power supply NOTE: Prevent any cord bunching by pulling cord through ...
Page 10 - Wall Installation
Page 10 Wall Installation This type of installation is similar to roof mounting, ensuring that the pipe extends at least 50mm past the wall surface refer figure 2. If the pipe length is shortened, reproduce the power cord exit slot on the inside of the wall. NOTE: By decreasing the length of the Ste...
Page 12 - Flat Roof Installation
Page 12 Figure 4: Flat roof installation Flat Roof Installation Flat roof mounting using optional mounting flange*. Engage locking screws in holes Backdraft shutter (optional) Seal 3 holes in stepped surface Seal between mounting flange and cover Up-stand and capping Power supply cord passing throug...
Page 13 - Through Wall Installation for Isodrive 900
Page 13 Figure 5: Wall installation Through Wall Installation for Isodrive 900 Fan Unit Wall Optional Shutter Assembly (200mm BDSS BUILD ASS)* Optional wall cover plate with notch at bottom P1108* Minimum pipe protrusion from wall surface Wall cover plate (optional part) Slot in pipe at bottom (6 O’...
Page 14 - Fan Unit Shutter Assembly for Isodrive 900 (Optional)
Page 14 Fan Unit Shutter Assembly for Isodrive 900 (Optional) 1. Assemble by fitting shutter assembly into fan inlet shroud moulding, ensuring that attaching screws align with holes. Alignment can be checked visually by folding in shutter flaps. 2. Fully tighten both screws and re-check fitment into...
Page 15 - Measurements for Isodrive 900
Page 15 Backdraft shutter (optional) Figure 7: Measurements for Isodrive 900 5. Measurements Measurements for Isodrive 900 (Not to Scale) 160mm 50mm 270mm 198mm 130mm Dektite 50mm 242mm 515mm 160mm
Page 17 - Assembling SteelFlex
Page 17 6. SteelFlex ™ Safety Duct Assembling SteelFlex ™ Safety Duct SteelFlex ™ safety duct must be secured to either the bell-mouth adapter ring or a 200mm mounting pipe. 1. Slide the steel ring clamp over the end of the duct then insert the bell-mouth adapter ring into the duct end Parts require...
Page 18 - Shallow Roof Space; Important Note
Page 18 6. SteelFlex ™ Safety Duct Shallow Roof Space In shallow roof spaces, do not crush or kink SteelFlex ™ ducting, as it will reduce air flow severely. 90 degree curve made of PVC or galvanise can be used as a substitute for the bend, refer to figure 12. Figure 10: Shallow roof space Figure 11:...
Page 19 - Securing SteelFlex
Page 19 6. SteelFlex ™ Safety Duct Securing SteelFlex ™ Safety Duct SteelFlex ™ safety duct must be installed with supports at maximum intervals of 1.5 metres. SteelFlex ™ safety ductwork can be supported by using good quality gaffer or aluminium foil tape. Provided that it does not restrict the int...
Page 20 - Parts List for Isodrive 900
Page 20 7. Parts List Parts List for Isodrive 900 1 2 3 4 5 6 7 8 9 10 11 12
Page 23 - Warranty; Disclaimer
Page 23 9. Warranty / Disclaimer Warranty (See warranty for more information) Isodrive motor has a 10-Year replacement product warranty.* The consumer is responsible for any charges associated with removal of the faulty unit and installation of the new unit. The customer is also responsible for any ...