SCAG 37621220 - Manual - manualsarea.com

Page 2 - PECO GRASS COLLECTION SYSTEM; TABLE OF CONTENTS; SECTION

2 PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Safety Alert Symbols - - - - - - - - - - - - - - - - - - - - - - 3Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4 I INTRODUCTION AND DESCRIPTION - -...

Page 3 - DANGER

3 SAFETY WARNING! WARNING! WARNING! WARNING! Safety Aler t Symbol Safety Signs NEVER ONLY AFTER STOPPING THE MOWER’S ENGINE AND WAITING FOR ALL MOVING PARTS TO COME TO A COMPLETE STOP. ALWAYS UP DOWN NEVER NEVER “ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” DANGER, WARNING, CAUTION operate the...

Page 4 - PECO LIMITED WARRANTY FOR NEW PRODUCTS

4 PECO LIMITED WARRANTY FOR NEW PRODUCTS A. WHAT IS WARRANTED? 1. PRODUCT WARRANTY: ALL DEFECTIVE PARTS MUST BE RETURNED TO PECO FOR INSPECTION TO DETERMINE VALIDITY OF WARRANTY CLAIMS. 2. PARTS REPLACED DURING WARRANTY: B. SECURING WARRANTY ADJUSTMENTS. C. ITEMS NOT COVERED BY PECO WARRANTY. D. UNA...

Page 5 - Section II; -1 Preparation Of Mower; -2 Top Main Frame Assembly

5 SECTION I INTRODUCTION AND DESCRIPTION 1-1 Introduction 1-2 Description We are pleased to have you as a PECO customer. Yourcollection system has been designed to give you a lowmaintenance, simple, and effective way to collect thegrass clippings from your mower. This manual isprovided to give you t...

Page 10 - -7 Mount Tube Assembly Installation

2-9 Engine/Blower/Blade Assembly Installation Place the engine/blower/blade assembly onto the enginemount arm assembly (Figure 2-9). Secure theengine/blower/blade assembly to the engine mount armassembly by using (4) 5/16"-18 x 1-1/2" hex boltsP#(K1157) and (4) 5/16"-18 flange nuts P#(K1...

Page 11 - -11 Blower Cone Installation; IMPELLER BLADE

11 2-11 Blower Cone Installation Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of(2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partiallythread the bolts into each of the two tabs located on theblower housing. Place blower cone so the two tabs line upwith the bolts then tighten completely. See Figu...

Page 13 - -18 Throttle Cable Installation

13 2-18 Throttle Cable Installation To install the throttle cable kit to the box assembly, alignthe large end of the slot in the throttle base plate (Figure2-18a) with the rivets located on the front of the boxassembly frame (Figure 2-18b). Place the throttle baseplate over the rivets, Slide the thr...

Page 14 - -3 Unloading The Collection System; SECTION IV; -1 Maintenance Checklist

SECTION III OPERATING INSTRUCTIONS 3-1 General Safety 3-2 Operation & Tips On Mowing Only qualified people familiar with this operator’s manualand the mower’s operator’s manual should operate thismachine. A. Perform BEFORE EACH USE maintenance list in paragraph 4-1. B. Start the engine/blower/bl...

Page 15 - SECTION V; -1 Par ts And Ser vice Infor mation; Tur n any PECO Lawn Vac into a total

15 Model Number Serial Number PECO OUTDOOR POWER EQUIPMENT Arden, Nor th Carolina 28704 WRITE THE MODEL AND SERIAL NUMBER IN THE BOX ABOVE FOR FUTURE REFERENCE. Unit Model Number:_________________________________ Unit Engine Size: __________________________________ Unit Serial Number: ______________...

Page 16 - SAFETY DECALS

SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur tosafety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R1054 Part #: R1049 Part #: R1057 Part #: R1053 Part #...

SCAG 37621220 - Manual

Table of Contents:

Summary

Other SCAG Models