Sanyo LNS-W32 - Manual
Sanyo LNS-W32 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 4 – FOCUS ADJUSTMENT
- Page 6 – LENS LOCK LATCHES; CONFIRM THE FOCUS
- Page 7 – Rotate the lens to obtain proper focus on outer; Lens cover is not used.; Mount the front cabinet with 2 screws.
- Page 8 – REMOVE THE LENS
- Page 9 – MOUNT THE LENS; Correcting the focus
Following checks and confirmations should be taken for safety.
C h e ck t h e fo l l ow i n g t h i n g s by t h e t i m e o f t h e c a b i n e t a s s e m bl y a f t e r t h e l e n s
replacement.
1. Check the lens is securely fixed.
2. Check no parts is missing, or no mounting part is loose.
LCD PROJECTOR LENS
MODEL LNS-W32
LENS REPLACEMENT PROCEDURE
NOTES ON LENS REPLACEMENT
The ZOOM, FOCUS and LENS SHIFT adjustment on the Top Control or the
Remote Control cannot be operated with this Lens.
Lens replacement should be performed by the qualified service personnel.
It should be followed by this procedure precisely.
Before attempt to replace the lens, confirm the model number (both the LCD
projector and the lens) and use the proper lens.
The lens cover is on the lens for protection. Be sure to remove the lens cover
before installation.
When installing or removing the lens, be careful not to stain, scratch or
damage the lens.
Following parts are contained in the packing.
1AA6P1P3217A- (ICZAA-A)
PARTS LIST
●
LENS
●
LIGHT-BLOCK SHEET BASE
●
DRIVER (3 mm, Green)
●
DRIVER (4 mm, Yellow)
●
LIGHT-BLOCK SHEET
●
SCREW
1 piece
1 piece (Part No. 610 310 8001)
1 piece (Part No. 610 287 7328)
1 piece (Part No. 610 275 6029)
1 piece Type PC1 (Part No. 610 310 7967)
1 piece Type PD1 (Part No. 610 294 3047)
2 pieces (Spare parts)
Some par ts are not used for installation or replacement. Keep these par ts and
drivers included in the lens for later use.
NOTE; Lens installation is different in cabinet design and lens attachment method
(Type A, B and C). Before installation the lens, check cabinet design and
proper installation should be made.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
-4- Fig-6 Fig-7 DRIVERIN THE LENS LENS MOUNTINGBRACKET 4 MOUNT THE LENS (See Figure-5 and 6) 5 M O U N T T H E L I G H T- B L O C K S H E E T A N D FRONT PANEL (See Figure-7) Remove protective caps (front and back) on the lens. Mount the lens on lens mounting bracket with 4 screws. Use the driver (4...
4 MOUNT THE LENS (See Figure-5) Remove protective caps (front and back) on the lens. Mount the lens on lens mounting bracket with Upper 2 screws. Use the driver (4 mm, Yellow) included with the lens to fasten the screws. Remove the lower 2 screws on the Lens. (Lower 2 screws are not used.) Slide the...
FOCUS ADJUSTMENT Set up the projector and project image on the screen.1. Loosen the Focus Lock Screw on the lens.2. Rotate the lens to obtain proper focus on center area of the screen. 3. Tighten the Focus Lock Screw.When proper focus is not observed at outer area ofthe screen, proceed to following ...
