Sanyo KMHS1872 - Manual
Sanyo KMHS1872 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – SPECIAL PRECAUTIONS; accidental injury or; WARNING
- Page 3 – CAUTION; Model
- Page 4 – Installation Site Selection; Front View
- Page 5 – Table 3
- Page 6 – How to Install the Indoor Unit; N O T E; Also avoid areas where elec-
- Page 7 – Rawl pl
- Page 10 – General precautions on wiring
- Page 13 – Push
- Page 15 – To unmount indoor unit; Risk of Electric Shock
- Page 16 – How to Test Run the Air Conditioner; I M P O R TA N T; OPERATION lamp
- Page 17 – Remote Control Unit Installation Position; To take out the remote control unit, pull it forward.
- Page 18 – -1. Address Setting of the Remote Control Unit; un
Model Combinations
Combine indoor and outdoor units only as listed
below.
Indoor Unit
Outdoor Unit
KMHS0772
CMH1972
KMHS0972
CMH2472
KMHS1272
CMH3172
KMHS1872
KMHS2472
Power Source:
60 Hz, single-phase, 230 / 208 VAC
Combinations of indoor and outdoor units
Connect indoor and outdoor units only in the combi-
nations listed in the catalog or installation manual.
Connecting any other model may result in
operation failure and system damage.
85264189998000 © SANYO 2006
In Canada
SANYO FISHER COMPANY
SANYO Canada Inc.
A DIVISION OF SANYO NORTH AMERICA CORPORATION
300 Applewood Crescent, Concord
21605 Plummer Street
Ontario, L4K 5C7, Canada
Chatsworth, CA 91311 U.S.A.
Contents
Page
IMPORTANT!
Please Read Before Starting
..................................
2
1.
GENERAL
..........................................................
3
1-1. Tools Required for Installation (not supplied)
1-2. Accessories Supplied with Unit
1-3. Optional Copper Tubing Kit
1-4. Type of Copper Tube and Insulation Material
1-5. Additional Materials Required for Installation
2.
INSTALLATION SITE SELECTION
...................
4
2-1. Indoor Unit
2-2. Embedding the Tubing and Wiring
3.
HOW TO INSTALL THE INDOOR UNIT
..............
6
3-1. Remove the Rear Panel from the Unit
3-2. Make a Hole
3-3. Install the Rear Panel on the Wall
3-4. Remove the Grille to Install the Indoor Unit
3-5. Shape the Indoor Side Tubing
3-6. Wiring Instructions
3-7. Wiring Instructions for Inter-unit Connections
3-8. Mounting
3-9. Drain Hose
4.
HOW TO TEST RUN THE AIR CONDITIONER
....
16
5.
REMOTE CONTROL UNIT INSTALLATION
POSITION
.........................................................
17
5-1. Mounting on a Wall
6.
ADDRESS SWITCH
..........................................
18
6-1. Address Setting of the Remote
Control Unit
7.
CONNECTING A HOME AUTOMATION
DEVICE
..............................................................
19
8.
INSTALLATION CHECK SHEET
......................
19
INSTALLATION INSTRUCTIONS
– Inverter Split System Air Conditioner –
COOL / DRY/ HEAT Model
This air conditioner uses the new refrigerant R410A.
Be sure to read the yellow instruction sheet
attached to the outdoor unit for models using the
new refrigerant R410A.
The illustrations are based on the typical appearance of
a standard model. Consequently, the shape may differ
from that of the air conditioner that you are installing.
N O T E
CAUTION
For Indoor Unit
05-351 KMHS0772_indoor 3/16/06 6:46 PM Page a
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 IMPORTANT! Please Read Before Starting This air conditioning system meets strict safety and operatingstandards. As the installer or service person, it is an importantpart of your job to install or service the system so it operatessafely and efficiently. For safe installation and trouble-free opera...
3 1. General This booklet briefly outlines where and how to install the air conditioning system. Please read over the entire set of instructions for the indoor and outdoor units and make sure all accessory parts listed are with the system before beginning. 1-1. Tools Required for Installation (not s...
4 1-5. Additional Materials Required for Installation 1. Refrigeration (armored) tape 2. Insulated staples or clamps for connecting wire (See local codes) 3. Putty 4. Refrigeration lubricant 5. Clamps or saddles to secure refrigerant tubing 2. Installation Site Selection 2-1. Indoor Unit AVOID: G di...
