Sanyo CH1251 - Manual
Sanyo CH1251 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – SPECIAL PRECAUTIONS; WARNING
- Page 3 – CAUTION
- Page 4 – Installation Site Selection
- Page 6 – How to Install the Indoor Unit; -1. Remove the Rear Panel from the Unit; N O T E
- Page 9 – General precautions on wiring
- Page 16 – Deburring; Refrigerant Tubing; -2. Flaring Procedure with a Flare Tool
- Page 17 – Tightening Torque; Clamp
- Page 18 – Indoor unit; Required time for evacuation when capacity
- Page 19 – Be sure to completely insert
- Page 21 – Pump Down; Pump Down Procedure; Action; Wide Tube Service; Basic Function of the Service Valves; Table 7
- Page 22 – Remote Control Unit Installation Position; When using the remote control unit
INSTALLATION INSTRUCTIONS
– Split System Air Conditioner –
Model Combinations
Combine indoor and outdoor units only as listed
below.
Indoor Units
Outdoor Units
KHS0951
CH0951
KHS1251
CH1251
Power Source:
60 Hz, single-phase, 115 V
KHS1852
CH1852
Power Source:
60 Hz, single-phase, 230/208 V
In Canada
SANYO FISHER COMPANY
SANYO Canada Inc.
A DIVISION OF SANYO NORTH AMERICA CORPORATION 300 Applewood Crescent, Concord
21605 Plummer Street
Ontario, L4K 5C7, Canada
85264189615003 © SANYO 2002
Chatsworth, CA 91311 U.S.A.
W
Contents
Page
IMPORTANT!
Please Read Before Starting .................................. 2
1.
GENERAL .......................................................... 3
1-1. Tools Required for Installation (not supplied)
1-2. Accessories Supplied with Unit
1-3. Optional Copper Tubing Kit
1-4. Type of Copper Tube and Insulation Material
1-5. Field Wiring
1-6. Additional Materials Required for Installation
2.
INSTALLATION SITE SELECTION ................... 4
2-1. Indoor Unit
2-2. Outdoor Unit
3.
HOW TO INSTALL THE INDOOR UNIT ............ 6
3-1. Remove the Rear Panel from the Unit
3-2. Make a Hole
3-3. Install the Rear Panel on the Wall
3-4. Remove the Grille to Install the Indoor Unit
3-5. Shape the Indoor Side Tubing
3-6. Wiring Instructions
3-7. Recommended Wire Length and Diameter
3-8. Wiring Instructions for Inter-unit Connections
3-9. Mounting
3-10. Drain Hose
4.
HOW TO INSTALL THE OUTDOOR UNIT ....... 15
4-1. Wiring Instructions for the Outdoor Unit
5.
REFRIGERANT TUBING .................................. 16
5-1. Use of the Flaring Method
5-2. Flaring Procedure with a Flare Tool
5-3. Caution before Connecting Tubes Tightly
5-4. Connecting Tubing between Indoor and
Outdoor Units
5-5. Insulation of Refrigerant Tubing
5-6. Taping the Tubes
5-7. Finishing the Installation
6.
AIR PURGING ................................................... 18
■
Air Purging with a Vacuum Pump (for Test Run)
■
Basic Function of the Service Valves
■
Pump Down
7.
REMOTE CONTROL UNIT INSTALLATION
POSITION ......................................................... 22
7-1. Mounting on a Wall
COOL / DRY/HEAT Model
IMPORTANT
Power source for CH0951 and CH1251 is 60 Hz,
single-phase 115 V.
01-385 AirCon 12/11/01 4:41 PM Page 1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 IMPORTANT! Please Read Before Starting This air conditioning system meets strict safety and operating standards. As the installer or service person, it is an important part of your job to install or service the system so it operates safely and efficiently. For safe installation and trouble-free op...
3 1. General This booklet briefly outlines where and how to install the air conditioning system. Please read over the entire set of instructions for the indoor and outdoor units and make sure all accessory parts listed are with the system before beginning. 1-1. Tools Required for Installation (not s...
4 1-6. Additional Materials Required for Installation 1. Refrigeration (armored) tape 2. Insulated staples or clamps for connecting wire (See local codes) 3. Putty 4. Refrigeration lubricant 5. Clamps or saddles to secure refrigerant tubing 2. Installation Site Selection 2-1. Indoor Unit AVOID: ● di...
