Page 2 - CAUTION; WARNING; safety information
2 – 10x Network Mini Smart Dome Camera CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a...
Page 3 - FCC Statement; Caution
English – 3 Do not expose the product to the direct airfl ow from an air conditioner.Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between internal and external of the dome camera. If you install this product in a low-temp area such as inside a col...
Page 4 - important safety instructions
4 – 10x Network Mini Smart Dome Camera important safety instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the ma...
Page 5 - contents; Introduction
English – 5 contents Introduction Features 7 Recommended PC Specifi cations 8 Compatible IP Routers 8 Product & Accessories 9 Parts Name & Functions 11 Installation DIP Switch Setup 13 Installation Using Surface Mount On The Ceiling 14 Installation Using Ceiling Mount Bracket 15 Installation...
Page 7 - introduction; FEATURES; Network Specifi cations; Reserved Presets for Special Purpose
English – 7 introduction FEATURES Network Specifi cations Powerful Dual Stream by using DSP based MPEG4, MJPEG compression Superior Video Quality and System Stability. High speed : Up to 30 fps at 720x480, 25 fps at 720x576. Web Browser based viewer support. Remote Pan/Tilt/Zoom control. Bidirection...
Page 8 - COMPATIBLE IP ROUTERS
8 – 10x Network Mini Smart Dome Camera introduction RECOMMENDED PC SPECIFICATIONS CPU : Pentium4/2.4GHz or higher Operating System : Windows XP(Service Pack 2) / Windows Vista Resolution : 1024x768 pixels or higher RAM : 512MB or higher Web Browser : Internet Explorer 6.0 or higher Video Card : Rade...
Page 9 - PRODUCT & ACCESSORIES
English – 9 introduction PRODUCT & ACCESSORIES SNC-C6225 Product Accessories Terminal Block Torx Screw Driver Surface Mount Gasket Screw & Plastic Anchor (4pcs) Quick Guide Audio Cable User Manual / IP Installer CD Cross Cable Core Filter Mount Bracket Option : Please use SADT-937WM for this...
Page 11 - PARTS NAME & FUNCTIONS
English – 11 introduction PARTS NAME & FUNCTIONS SNC-C6225 ❖ Dome Cover Do not remove the protection vinyl from dome cover before fi nishing all installation process to protect dome cover from scratches or dust. Surface Mount Bracket This is used to install the camera directly on the ceiling. Af...
Page 13 - DIP SWITCH SETUP; Camera ID Setup; Communication Protocol Setup; Communication Baud rate Setup; Installation
English – 13 DIP SWITCH SETUP Before you install the camera, you should set the DIP switches to confi gure the camera ID, Baud Rate and communication protocol. Camera ID Setup ID number of camera is set using binary number. The example is shown bellow. Pin 1 2 3 4 5 6 7 8 ID Value 1 2 4 8 16 32 64 1...
Page 14 - installation; RS-485 Termination Resistor
14 – 10x Network Mini Smart Dome Camera installation RS-485 Termination Resistor Pin 8 is used for ON/OFF of RS-485 Termination. Normally, it must be OFF state. Especially when you have trouble with long Daisy chain style connection, turn ON this termination switch of last camera. Pin 8 : RS-485 Ter...
Page 17 - CABLING; Power Connection
English – 17 installation CABLING SNC-C6225/SNC-C7225 Power Connection Please, check the voltage and current capacity of rated power carefully. Rated Power Input Voltage Range Power Consumption SNC-C6225 SNC-C7225 DC 12V DC 11V ~ 15V 15W 15W(Heater Off) / 25W(Heater On) RS-485 Communication For PTZ ...
Page 18 - Video Connection; Audio Input/Ouput Connection
18 – 10x Network Mini Smart Dome Camera installation Video Connection Connect with BNC coaxial cable. Audio Input/Ouput Connection Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT port of the amplifi er that the microphone is connected to direct Mic Connection: Set Au...
Page 19 - INSERTING/REMOVING AN MICRO SDHC MEMORY CARD; Inserting an Micro SDHC Memory Card
English – 19 installation INSERTING/REMOVING AN MICRO SDHC MEMORY CARD Inserting an Micro SDHC Memory Card Push the Micro SDHC memory card in the direction of the arrow shown in the diagram. Do not force the memory card in. If you can’t insert the memory card into the slot with ease, you might be in...
Page 20 - What is a memory card?
20 – 10x Network Mini Smart Dome Camera installation MEMORY CARD INFORMATION (NOT INCLUDED) What is a memory card? The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices. Selecting ...
Page 21 - operation; AUTO CALIBRATION; STARTING OSD MENU
English – 21 operation CHECK POINTS BEFORE OPERATION Before power is applied, please check the cables carefully. The camera ID of the controller must be identical to that of the camera to be controlled. The camera ID can be checked in the System Information of OSD Menu. If your controller supports m...
Page 22 - PRESET
22 – 10x Network Mini Smart Dome Camera operation PRESET Function Max. 127 positions can be stored as Preset position. The Preset number can be assigned from 1 to 128, but 95 is reserved for starting OSD menu. Camera characteristics (i.e. White Balance, Auto Exposure) can be set up independently for...
Page 23 - SCAN
English – 23 operation SCAN Function The Scan function allows running sequence of Presets, Pattern and/or Auto Pans. Max 8 Scan can be stored. Each Scan can have max 20 action entities which can be preset, pattern or Auto Pan. Preset speed can be set up and the repeat number of Pattern & Auto Pa...
Page 24 - OSD DISPLAY OF MAIN SCREEN
24 – 10x Network Mini Smart Dome Camera operation GENERAL/SPECIAL Image Setup WB (White Balance) and AE (Auto Exposure) can be set up independently for each preset. There are 2 modes, “ General ” mode & “ Special ” mode. The General mode means that WB or AE can be set up totally and simultaneous...
Page 25 - how to use osd menu; STRUCTURE OF THE SETUP MENU
English – 25 how to use osd menu STRUCTURE OF THE SETUP MENU SYSTEM INFORMATION DISPLAY SETUP MOTION SETUP FUNCTION SETUP NTSC/PAL AUTO/SAMSUNG 4800/9600/19200/38400 1~255 XX:XX:XX:XX:XX:XX ON/OFF AUTO/OFF/ON AUTO/OFF/ON AUTO/OFF/ON AUTO/OFF/ON ON/OFF MASK NO. DISPLAY CLEAR <EDIT MASK> CELSIUS...
Page 27 - MAIN MENU
English – 27 how to use osd menu MAIN MENU SYSTEM INFORMATION Shows info and current confi guration. DISPLAY SETUP Enable/Disable of OSD display on Main Screen. MOTION SETUP Setup for motion related settings. FUNCTION SETUP Setup for various functions such as Preset, Auto Pan, Pattern, Scan and Sche...
Page 28 - Privacy Zone Area Setup; MOTION SETUP
28 – 10x Network Mini Smart Dome Camera how to use osd menu DISPLAY [ON/OFF] Sets if camera makes mask shows or not on images. CLEAR [CANCEL/OK] Deletes data in the selected mask NO. Privacy Zone Area Setup Move camera to area to mask. Then the menu to adjust mask size will be displayed. Privacy Zon...
Page 29 - Parking Action Setup; FUNCTION SETUP
English – 29 how to use osd menu Parking Action Setup If Park Enable is set to ON, camera runs assigned function automatically if there is no PTZ command during assigned “ WAIT TIME ”. PARK ENABLE [ON/OFF] WAIT TIME [5 sec ~ 4 hour] The time is displayed with “hh:mm:ss” format and you can change thi...
Page 30 - PRESET SETUP; Edit Preset Scene
30 – 10x Network Mini Smart Dome Camera how to use osd menu PRESET SETUP PRESET NO. [1~128] If a selected preset is already defi ned, camera moves to pre-defi ned position and preset characteristics such as Label and Relay Outputs show on monitor. If a selected preset is not defi ned, “ UNDEFINED ” ...
Page 31 - AUTO PAN SETUP
English – 31 how to use osd menu If you want to use blank, choose Space character (“ ”). If you want to delete a character before, use back space character (“ ”). e If you complete the Label editing, move cursor to “ OK ” and press ENTER key to save completed label. To abort current change, move cur...
Page 32 - Edit Pattern; SCAN SETUP; Edit Scan
32 – 10x Network Mini Smart Dome Camera how to use osd menu Edit Pattern c By using Joystick, move to start position with appropriate zoom. To start pattern recording, press ENTER key. d Move camera with joystick of controller or run preset function to memorize the path (mostly curve path) in a sele...
Page 34 - SCHEDULE SETUP; Edit Schedule
34 – 10x Network Mini Smart Dome Camera how to use osd menu SCHEDULE SETUP MASTER ENABLE [ON/OFF] Decide whether Schedule function is active or not. CLEAR SCHEDULE [CANCEL/OK] Delete all data in current Menu EDIT SCHEDULE Start editing Schedule. Edit Schedule c After move the Cursor to the number by...
Page 35 - White Balance Setup
English – 35 how to use osd menu CAMERA SETUP Setup the general functions of zoom camera module FOCUS MODE [AUTO/MANUAL/ONEAF] Sets camera focus mode. ONEAF This mode exchanges focus mode automatically between Manual Focus mode and Auto Focus mode. Manual Focus mode activates in preset operation a...
Page 36 - SYSTEM SETUP
36 – 10x Network Mini Smart Dome Camera how to use osd menu SHUTTER [ESC/A. Flicker/Manual(×128~1/120000 sec)] If Iris is set to Manual and Shutter Speed is set to ESC, Shutter Speed should have highest priority. If Shutter Speed is set to A. Flicker, to remove Flicker, Shutter Speed should be set t...
Page 38 - SYSTEM INITIALIZE; Initial Confi guration Table
38 – 10x Network Mini Smart Dome Camera how to use osd menu SYSTEM INITIALIZE CLEAR ALL DATA Deletes all confi guration data such as display, camera, motion setup and so on. CLR DISPLAY SET Initializes Display Confi guration CLR CAMERA SET Initializes Camera Confi guration CLR MOTION SET Initializes...
Page 39 - network connection & setup; Network connection and setup processes are given as follows.
English – 39 network connection & setup You can set up the network settings according to your network confi gurations. Network connection and setup processes are given as follows. Connect the camera to an IP router with a xDSL/Cable modem. (Page 39~40) Connect the camera to an IP router with loc...
Page 40 - Setting the IP address
40 – 10x Network Mini Smart Dome Camera network connection & setup ex2) If the address (LAN IP) of the IP router is 192.168.0.1 IP address: 192.168.0.100 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.0.1 ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1 IP address: 192.168.xxx...
Page 42 - Connecting a local PC in the IP router to the camera; Connecting to the camera from an IP router external PC
42 – 10x Network Mini Smart Dome Camera network connection & setup Connecting a local PC in the IP router to the camera Run the IP Installer on your local PC and search for the camera. If found, double-click the camera to start the Internet browser and try to connect to the camera. Alternately, ...
Page 43 - Connecting to the camera from a remote PC
English – 43 network connection & setup CONNECTING THE CAMERA DIRECTLY TO A DHCP-BASED XDSL/CABLE MODEM This is enabled for a modem using DHCP. Setting the IP Router Set the IP address referring to " Setting Static IP " on page 46 or " Setting Dynamic IP " on page 49. Launch an I...
Page 44 - Connecting to the camera from a local PC in the LAN
44 – 10x Network Mini Smart Dome Camera network connection & setup CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN Launch an Internet browser on the local PC. Enter the IP address of the camera in the address bar of the browser. A remot...
Page 45 - SEARCHING FOR THE CAMERA; IP Installer screen layout
English – 45 network connection & setup SEARCHING FOR THE CAMERA IP Installer screen layout 1 Device Name : Model name of the connected device. 2 Mode : Shows the current selection between < Static > and < Dynamic >. 3 MAC Address : The Mac address of the network interface of the cam...
Page 46 - MANUAL NETWORK SETTING; setting static ip
46 – 10x Network Mini Smart Dome Camera MANUAL NETWORK SETTING Run the < IP Installer.exe > program and display the camera list found on the screen. For the initial run, the [ Auto Set ] and [ Manual Set ] button are all disabled. Select a camera you want from the camera list. Confi rm the MAC...
Page 47 - If more than one camera are connected to an IP Router
English – 47 setting static ip In the < PORT > fi elds, set up port numbers. < HTTP Port >: A HTTP port used to connect to a camera using the Internet browser. The default value is 80. The HTTP port value can be changed by using the up/down button to the right. The HTTP port number start...
Page 48 - AUTOMATIC NETWORK SETTING
48 – 10x Network Mini Smart Dome Camera setting static ip AUTOMATIC NETWORK SETTING Run the < IP Installer.exe > program and display the camera list found on the screen. For the initial run, the [ Auto Set ] and [ Manual Set ] button are all disabled. Select a camera you want from the camera l...
Page 49 - DYNAMIC IP SETTING; Examples of using Dynamic IP; setting dynamic ip
English – 49 DYNAMIC IP SETTING Examples of using Dynamic IP If the camera is installed on an IP router and obtains an IP using DHCP. If the camera is connected directly to a xDSL/Cable modem using DHCP. If an IP is allocated by the internal DHCP server in local area networking. Dynamic IP Check Whe...
Page 50 - using the camera; CONNECTING TO THE CAMERA; Connecting to the camera
50 – 10x Network Mini Smart Dome Camera using the camera CONNECTING TO THE CAMERA Connecting to the camera General Run an Internet browser. Enter the IP address for the camera in the Address input box.ex) IP Address: 192.168.1.200 → http://192.168.1.200 - The login window appears. If the HTTP port n...
Page 51 - Connecting to the camera using the IP Installer program; INSTALLING ACTIVEX; For Windows XP Service Pack 2
English – 51 using the camera Checking the DDNS address A DDNS address consists of < e > + < Last 6 digits of the MAC address > + < websamsung.net >. ex) - If the MAC address of the camera is 00: 0D : f1 : 30 : 00 : 2c → e + 30002c + websamsung.net = e30002c. websamsung.net The IP ...
Page 52 - Logging to the camera
52 – 10x Network Mini Smart Dome Camera using the camera Logging to the camera For the fi rst login, the username is “root” and password is “4321”. Type “root” in the < User name > input box. Type “4321” in the < Password > input box. If you have changed the old password, type the new pa...
Page 53 - MAIN SCREEN; web viewer
English – 53 MAIN SCREEN In this section, the main GUI of the Network Smart Dome will be explained. ! Click this menu to enter the search screen. @ Click this menu to enter Setup Tool. # Click this menu to view Network Smart Dome Camera Information. $ Live video Display. % Display the live screen in...
Page 54 - POWER PTZ; USING THE CAMERA
54 – 10x Network Mini Smart Dome Camera web viewer + Preset / Pattern / Auto Pan / Scan Buttons Preset: Run, Save or Delete the Preset positions memorized in the camera. Pattern: Run the Pattern function programmed in the camera. (To create this function, use OSD Menu.)Auto Pan: Run the Auto Pan fun...
Page 56 - USING THE SD SEARCH VIEWER SCREEN
56 – 10x Network Mini Smart Dome Camera web viewer USING THE SD SEARCH VIEWER SCREEN If you connect to the camera, the following SD Search Viewer screen appears. SD Search Viewer Screen Layout Name Function and Description 1 Date You can select the desired date to search for events generated. 2 Thum...
Page 57 - SETTING THE CAMERA; SETUP Screen Layout; setup tool
English – 57 SETTING THE CAMERA You can set various functions such as Basic Setting, System, Event, Network, etc. To setup the camera In the viewer screen, click the [ SETUP ] tab. The setup window appears. ❖ SETUP Screen Layout ❖ setup tool SETUP BASIC SYSTEM VIDEO & AUDIO IP USER LANGUAGE DIS ...
Page 59 - IP
English – 59 setup tool IP IP Type Select the IP setting type from < Static IP >, < Dynamic IP > or < PPPoE IP >. MAC Address Shows the Ethernet MAC Address. Since this value is used to create a DDNS address, confi rm the value. IP Address Shows the currently confi gured IP address...
Page 60 - USER; LANGUAGE
60 – 10x Network Mini Smart Dome Camera setup tool RTP Port Range Set up the range of port number to use for RTP Protocol. The Start number of RTP Port has to be even number and the last number must be greater than the start number +4. I.e. the difference should be at least 4. RTP Multicast Address ...
Page 61 - Current System Time; LOG; System Log List; SOFTWARE UPDATE; Current Version; How to upgrade
English – 61 setup tool DATE/TIME Current System Time Shows the time according to the setting of System Time Setup. System Time Setup You can set the time synchronized with NTP server (Time Server) or PC, or manually setup.( Ú The date can be confi gured between 1 January 2000 and 31 December 2037) ...
Page 62 - RESET; HTTPS; TRANSFER SETUP; FTP Transfer
62 – 10x Network Mini Smart Dome Camera setup tool RESET Restart Re-boots Network Smart Dome Camera. Factory Default Reset system confi gurations to the factory defaults with following two options.Except Network Parameter: Reset except values on Network Parameters. (IP Address, Gateway, Subnet Mask,...
Page 63 - RECORD SETUP
English – 63 setup tool User ID Enter a user account ID to connect to login the FTP server. Password Enter a user account password to login the FTP server. Test To test FTP transmission, Click [ Test ] button. Connect to the confi gured FTP server and conduct image transmission test automatically.Wh...
Page 64 - ALARM IMAGE SETUP
64 – 10x Network Mini Smart Dome Camera setup tool Options Determine whether or not you wish to receive Email notifi cation of insuffi cient capacity warnings. ALARM IMAGE SETUP Transfer Mode You can select a method to send an alarm image from the < FTP Transfer >, < E-Mail Transfer > an...
Page 65 - MOTION; Motion Sensitivity; Activation Time
English – 65 setup tool event is generated during the alarm output, the delay time is recalculated on the basis of the most recently generated an alarm.< Alarm Image Transfer >: If < On > is selected, a JPG image is transmitted through FTP or Email(SMTP) or saved on the Micro SDHC memory...
Page 66 - To set a motion detection target area; SCHEDULE; Schedule Transfer Function; STREAMING SETUP; Streaming Protocol
66 – 10x Network Mini Smart Dome Camera setup tool To set a motion detection target area You can set a specifi c area to detect a motion in. 1) In the MOTION window, click the [ Motion Area ] button.- The Motion Area window appears.- You can set a specifi c area to detect a motion in. 2) Click over ...
Page 67 - DDNS
English – 67 setup tool UDP: It is a protocol appropriate to transmit a large amount of data such as multimedia data in short time. However, it provides higher transmission effi ciency than TCP especially over high speed connections faster than 100Mbps. With multicast activated, it is not possible t...
Page 68 - SNMP; SNMP User Setup
68 – 10x Network Mini Smart Dome Camera setup tool SNMP The system information of the cam can be monitored and changed by SNMP. SNMPv1 or SNMPv2 are utilized to monitor of the system information and SNMPv3 enables to change the system information. SNMP User Setup The version3 can set up the account ...
Page 69 - appendix; TROUBLESHOOTING
English – 69 appendix TROUBLESHOOTING PROBLEM SOLUTION I can’t access the camera from a web browser. • Check to make sure that the camera’s Network settings are appropriate. • Check to make sure that all network cables have been connected properly. • If connected using DHCP, verify that the camera i...
Page 71 - SPECIFICATIONS
English – 71 appendix SPECIFICATIONS SNC-C6225N/P Item Details NTSC PAL Camera CCD 1/4" Interline Transfer CCD Max. Pixels 811(H) x 508(V) 410K 795(H) x 596(V) 470K Effective Pixels 768(H) x 494(V) 380K 752(H) x 582(V) 440K Horizontal Resolution Color : 520 / BW : 570 TV Line S/N Ratio 50 dB (AG...
Page 74 - DIMENSION
74 – 10x Network Mini Smart Dome Camera appendix DIMENSION SNC-C6225 ❖ Unit (mm) 3/4" PIPE THREAD
Page 76 - Correct Disposal of This Product
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charg...
