Page 2 - IMPORTANT SAFETY INSTRUCTIONS
English-2 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these Instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufactur...
Page 3 - CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
Graphic Symbol Explanation The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons....
Page 4 - IMPORTANT SAFEGUARDS; Caution
IMPORTANT SAFEGUARDS Caution Power source is indicated on the rear of the set. It contains high-voltage parts. If you remove the cover, it may cause fire or electric shock. Do not remove thecover by yourself. (Control switches are at the front of the monitor.) 1. Read Instructions : All the safety a...
Page 7 - FCC & ICES Information; Warning
18. Replacement Parts : When replacement parts are required, be sure the service technician has used replacement parts specified by Samsung or have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards. 19. Safety Check : Upon ...
Page 8 - Information to user; for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC ...
Page 9 - IC Compliance Notice
The party responsible for product compliance: SAMSUNG ELECTRONICS CO., LTD. America QA Lab of Samsung 3351 Michelson Drive, Suite #290, Irvine, CA92612 USA IC Compliance Notice This Class (A) digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet app...
Page 10 - Contents; Chapter 1: System Components and Installation; -4) CAMERA composition and connecting method; Chapter 2: MONITOR FRONT PANEL KEY Function and
English-10 Contents IMPORTANT SAFETY INSTRUCTIONS .................................. 2 IMPORTANT SAFEGUARDS ..................................................... 4 FCC & ICES Information .............................................................. 7 Chapter 1: System Components and Installatio...
Page 12 - -1) Environmental requirements for installation and safety; malfunction and reduce system downs due to environmental causes.
Chapter 1: System Components and Installation 1-1) Environmental requirements for installation and safety This section describes the environmental requirements for safe installation and use. Install the product on a flat table or in a rack. It should be used only when level and should not be used wh...
Page 14 - -3) CAMERA composition and installation method; c. Camera fitting groove; the camera if necessary.
English-14 1-3) CAMERA composition and installation method 1) Standard Camera composition (SOC-C120P) a. Lens It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide area. b. Microphone Capable of picking up all sound in the vicinity of the camera location and trans...
Page 19 - Function Switch; A function switch for the PIR sensor operation.; PIR Sensor; PIN
English-19 ⑤ Function Switch A function switch for the PIR sensor operation. ➅ PIR Sensor A thermal heat sensor that detects infrared radiation projected by warm objects. ⑦ Microphone Capable of picking up all sound in the vicinity of the camera location and transmitting to the monitor. ⑧ Electronic...
Page 20 - Camera installation Hints
English-20 Camera installation Hints 1. Do not install directly towards rising or setting sun. Can cause burn or damage to internal options. 2. Do not limit desired detection zone by interference of curtains, screens, potted plants, etc. 3. Also, do not locate it in front of source of water/oil vapo...
Page 23 - counterclockwise slightly. The lens body will move.
English-23 6. Adjust the direction of the lens. 1) Use the cross (+) screw driver to turn the screw (indicated by the arrow in the illustration) counterclockwise slightly. The lens body will move. 2) Tilt the lens body down about 10° from the horizontal, and then turn the screw clockwise to fasten i...
Page 24 - Installing the Camera using the Mount-Corner
English-24 Installing the Camera using the Mount-Corner 1. Choose an installation site that can suffi ciently support 5 times the weight of the equipments to be installed. 2. Place the mount-corner to the corner to which you want to install the camera and mark screw holes with a pencil (indicated by...
Page 25 - the cable terminal on the on the case-rear.
English-25 4. Remove the screw (BH M2.6) at the bottom of the main unit by turning it counterclockwise, and then lift the assy-case front as you push it upward to detach it from the case-rear. ( ❊ Do not apply excessive force, as doing so may damage the inside assembly. ❊ ) Assy-case front Screw (BH...
Page 29 - Operating Temperature :
• Loosen the handle by turning it in a counter clockwise direction and then adjust the camera position . Tighten the handle, turning it clockwise, and lock the camera in position. • Connect the camera cable to the camera. (3) Specifications Use : Indoor Installation : Wall or Ceiling Dimensions : 57...
Page 30 - Please check whether or not it is properly connected.; Connection status checking method :; The initial screen mode of monitor is quad mode.
English-30 1-4) CAMERA Composition and Connecting Method to MONITOR After positioning monitor and installing three cameras to a desired location, please connect CAMERA to MONITOR through CAMERA CABLE (MCB-60 or MCB-100) as shown in the below figure. Please check whether or not it is properly connect...
Page 31 - ) External terminal connecting method for CAMERA
English-31 1-5) External terminal connecting method for CAMERA and MONITOR 1) External terminal connecting method for CAMERA • An additional PIR sensor or external sensor can also be connected. • The additional PIR sensor can be connected as shown in the above graphic. • Sensor’s trigger signal is N...
Page 32 - -6) Whole System connection and configuration
English-32 f) Connect the A/O (HOT) terminal on the rear panel to the Alarm IN terminal of the VCR. g) Connect the A/O (COLD) terminal on the rear panel to the Ground terminal of the VCR. h) Connect the A/R terminal on the rear panel to the Alarm Reset terminal of the VCR. i) Connect the G (ground) ...
Page 33 - Front Panel; ENTER; ENTER; KEY
English-33 Chapter 2: MONITOR FRONT PANEL KEY Function and Using Method Front Panel 2-1) TALK KEY TALK KEY allows users to transmit voice signal to intended camera by inputting voice with built-in MIC in the front of the monitor. For this function, select a target camera (CH 1, 2, 3, 4) with the œ œ...
Page 34 - event such as an alarm or loss at POWER SAVE MODE occurs.; Alarm function can be cancelled while the alarm is working.; Allows users to display QUAD-A or QUAD-B at QUAD DISPLAY MODE.; MODE, the OSD “NO SIGNAL” will be displayed.
English-34 2-4) POWER SAVE- KEY Allows users to set POWER SAVE MODE of monitor. PICTURE screen is off when the POWER SAVE KEY is pressed, and the ON/OFF status of the monitor can be judged through LED ON/OFF status. Users can exit from POWER SAVE MODE by pressing POWER SAVE BUTTON again under pictur...
Page 37 - -1) ADJUST MENU function and setting method
English-37 Chapter 3: Setting each item function at SETUP MENU Pressing the MENU BUTTON of the FRONT PANEL allows users to enter SETUP MENU and see the following menu OSD box. Setting method of each SETUP MENU function and operation is as follows. 3-1) ADJUST MENU function and setting method • Funct...
Page 39 - Move to #4. DISPLAY SETTING MENU by using; SWITCH at
English-39 3-4) DISPLAY MENU function setting • Function : Allows users to select the color and ON/OFF of borderline at QUAD DISPLAY. • Setting method : Move to #4. DISPLAY SETTING MENU by using œ œ ENTER √ √ SWITCH at SETUP MENU, then press the ENTER SWITCH to display the OSD as shown in the figure...
Page 41 - Allows users to set the ALARM MODE for each camera.; SWITCH at SETUP
3-6) ALARM MENU Function setting • Function: Allows users to set the ALARM MODE for each camera. • Setting method: Move to #6. ALARM MENU by using œ œ ENTER √ √ SWITCH at SETUP MENU, and press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting sta...
Page 42 - -7) VIEW EVENT LOG MENU function and setting method; Displays the time and date of camera event and type of event.; SWITCH. A Total of 64 events can be listed.
English-42 06/01/03 13:14:00 NO CH MM/DD/YY HH:MM:SS EVT 01 07 02/10/03 10:00:30 A 02 01 02/11/03 11:22:00 L 03 01 06/01/03 12:33:01 - 04 02 06/01/03 13:01:03 - 05 01 --/--/-- --:--:-- - 06 01 --/--/-- --:--:-- - 07 01 --/--/-- --:--:-- - 08 01 --/--/-- --:--:-- - 3-7) VIEW EVENT LOG MENU function a...
Page 43 - Chapter 4: DISPLAY MODE setting method; select a target camera by turning; SWITCH left and right. After that, press the ENTER
English-43 Chapter 4: DISPLAY MODE setting method 4-1) SINGLE SCREEN DISPLAY Initial display mode of monitor is QUAD-A. In case users want to see the camera image at full mode, select a target camera by turning œ œ ENTER √ √ SWITCH left and right. After that, press the ENTER SWITCH and selected came...
Page 44 - * At QUAD MODE display from SINGLE MODE or SEQUENCE MODE
English-44 4-2) QUAD MODE DISPLAY Users can switch SINGLE DISPLAY MODE and SEQUENTIAL DISPLAY MODE to QUAD DISPLAY MODE, or QUAD-A (QUAD-B) to QUAD-B (QUAD-A), or PIP MODE to QUAD MODE, press the QUAD/PAGE KEY. * At QUAD MODE display from SINGLE MODE or SEQUENCE MODE CH3 CH3 DISPLAY QUAD MODE DISPLA...
Page 46 - on PIP screen ,the main screen will change. If you press the; selected on DISPLAY MENU in SETUP MENU.
English-46 4-4) PIP MODE DISPLAY Can be used to see PIP screen in Single screen mode. If you press the œ œ ENTER √ √ on PIP screen ,the main screen will change. If you press the œ œ ENTER √ √ to the left and right,the main screen can be transferred to another channel. Sub-screen location can be sele...
Page 47 - SWITCH left and
English-47 4-5) ZOOM MODE DISPLAY When users want to see zoomed image of a specific area of the display, press the ZOOM KEY in the front to display zoom selection area. Select zoom target area by turning œ œ ENTER √ √ SWITCH left and right, and press the ENTER SWITCH, then, the selected area will be...
Page 48 - Chapter 5: Each product feature
English-48 Chapter 5: Each product feature SOC-C120P : Standard Camera Model Name Broadcasting System Imaging Device Effective Pixels Synchronization Resolution Signal Output S/N Ratio Minimum Object Illumination Gamma Correction Lens Auto Exposure Audio I/O Connectors Operating Temperature Power So...
Page 50 - OBSERVATION MONITOR
English-50 Video Input Video Output Voice Input Voice Output Alarm/Motion Features: Connected to Alarm Box/Camera Sequence Event List Display mode Horizontal Resolution Operation Temperature CRT Dimension (W x D x H (mm)) Weight Power consumption High Voltage (KV) Operation Humidity Range AC Input R...
Page 51 - Memo
Page 52 - Printed in Korea
