Samsung SMC-152FP - User Manual

Eng-8 Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of th...

Eng-9 The party responsible for product compliance: SAMSUNG ELECTRONICS CO., LTD. America QA Lab of Samsung 3351 Michelson Drive, Suite #290, Irvine, CA92612 USA IC Compliance Notice This Class (A) digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. C...

Eng-10 Contents IMPORTANT SAFETY INSTRUCTIONS .................Eng-2 IMPORTANT SAFEGUARDS ................................... Eng-4 FCC information .......................................................... Eng-7 Front Panel Components and Controls ...................... Eng-11 SMC-210F, SMC-150F • ...

Eng-11 Power Switch On/off switch. If you press this button, the monitor is turned on and the LED of selected input signal is lit. VIDEO Input Selection Switch It selects video and audio input signal. To change input signal, press this button. VOLUME, DATA Control Switch VOLUME key has two functions...

Eng-14 Using the Auto Mode The RED indicator light is lit when Auto Mode is selected. In the Auto mode, the camera input channels will automatically switch by following sequence: Camera 1 → Camera 2 → Camera 3 → Camera 4, where the switching interval is set in the MENU option. (In the MENU option, a...

Eng-15 Using the Auto-Skip Mode When the Auto-skip options is set in the MENU settings, and no input signals are found for the channels 2, 4 and VCR, the Monitor will operate as follows: After 1 second After 1 second After 1 second (After scanning 4 channels) Camera 2 Scanning No Input Signal Camera...

Eng-16 Using the Manual Mode The GREEN indicator light is lit when Manual Mode is selected. This option allows the user to manually select either Camera OR VCR input channel accordingly as follows: CAMERA 1 Button If this button is pressed, the menu setting will be set to Camera 1. CAMERA 2 Button I...

Eng-17 Using the MENU button Press the MENU button for MENU settings. MENU Button - VOLUME If the MENU Button is pressed, all user controllable menus will be displayed in the following sequence: Contrast ➔ Brightness ➔ Sharpness ➔ Color ➔ Tint(NTSC only) ➔ Auto Timer ➔ Auto Skip ➔ Camera OSD ➔ (Lang...

Eng-20 Exit MENU • The Menu mode will exit automatically after 20 seconds of no user input. Adjusting VOLUME • In the MANUAL Mode, use the VOLUME button to adjust the volume of the selected channel. • Press the VOLUME button to decrease, or press the VOLUME button to increase the volume. • Monitor d...

Eng-21 Rear Panel Components and Controls CAMERA IN (1~4), VIDEO LINE IN(A, B) Camera INPUT connector. Input connectors for up to 4(2) cameras MONITOR OUT, VIDEO LINE OUT(A,B) VIDEO OUTPUT connector. VCR IN(VIDEO) VCR INPUT connector. Connect to the VCR. AUDIO IN (1~4), AUDIO LINE IN(A, B) AUDIO INP...

Eng-22 Connections CCD Camera 1 CCD Camera 2 CCD Camera 1 CCD Camera 2 CCD Camera 3 CCD Camera 4 TimeLaps VCR SMC-212F, SMC-152F SMC-210F, SMC-150F

Eng-23 Maintenance If the quality of the picture on the COLOR MONITOR is poor and cannot be improved, inspect all system connections and cable runs. Repairs should be performed by a qualified technician with adequate test equipment and facilities.

Eng-24 Specifications SMC-152FP/SMC-150FP/SMC-152FN/SMC-150FN (NTSC/PAL) 15” diagonal, 0.6mm stripe pitch, 90° deflection SMC-152FP/152FN : 4 Channel Input/1 Channel Output. SMC-150FP/150FN : 2 Channel Input/2 Channel Output. VCR INPUT 1.0Vp-p BNC jack SMC-152FP/152FN : 4 Channel Input/1 Channel out...