Page 2 - Safety Instructions; Notational
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property dam- age. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result...
Page 3 - Installation
Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power ...
Page 4 - Clean
Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the in- ternal tempera...
Page 5 - Others
When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • Otherwise, it may result in fire. When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. When cleaning the product, disconnect the power cord ...
Page 10 - Introduction; Package Contents
Introduction Package Contents Note Please make sure the following items are included with your PDP Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure a...
Page 11 - Ferrite Core
PDP Display Manuals Quick Setup Guide Warranty Card (Not available in all loca- tions) User's Guide Cables Power Cord D-Sub Cable Others Remote Control Batteries (AAA X 2) (Not available in all loca- tions) Ferrite Core for Power Cord Sold separately DVI Cable Wall Mount KIT BNC to BNC Cable Network...
Page 12 - SEL
Your PDP Display Front SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only al- lowed for external devices that are connected to the PDP Display at the time. [PC] → [DVI] → [AV] → [HDMI] → [MagicInfo] → [BNC] → [Component] Note • MagicInfo can only be enabled when ...
Page 13 - Remote Control Sensor; Aim the remote control towards this spot on the PDP Display.; Rear; Note; POWER IN; The power cord plugs into the PDP Display
Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your PDP Display OFF when it is not needed or when leaving it unattended for long periods. Remote Control Sensor Aim the remote control towards this spot on the PDP Dis...
Page 14 - DVI OUT
RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port RGB IN (PC Connection Terminal (In- put)) • Use a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) • Connect the RGB IN port on the monitor to the BNC port on the PC using the RGB to BNC cable. DVI IN (PC Video Connection ...
Page 16 - Kensington Lock; Using the Anti-Theft Kensington Lock
Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustra- tion depending on the manufacturer. Refer to the manual provided with ...
Page 21 - Wall Bracket Assembly
Wall Bracket Assembly Note There are two hinges(left and right). Use the correct one. 1. Insert and tighten the Captive Screw in the direction of the arrow. When done, mount the wall bracket on the wall. A - Captive Screw B - Wall Bracket C - Hinge (Left) D - Hinge (Right) 2. Before drilling into th...
Page 22 - To mount the product on the wall bracket
of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A. To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) 1. Remove the 4 screws on the...
Page 23 - Wall Bracket Angle Adjustment
4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A - PDP Display B - Wall Bracket...
Page 30 - Connections; Connecting a Computer; one from the following options.
Connections Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, [RGB IN] port on the back of your PDP Display and the 15 pin D-sub Port on ...
Page 32 - Connecting to Other devices; devices, refer to the contents under Adjusting Your PDP Display.; Connecting AV Devices
Connect the audio cable for your PDP Display to the audio port on the back of the PDP Display.Connect the power cord for your PDP Display to the power port on the back of the PDP Display. . Note • Turn on both your computer and the PDP Display. • Contact a local SAMSUNG Electronics Service Center to...
Page 33 - Play the DVD, VCR or Camcorder with a DVD disc or tape inserted.; Connecting to a Camcorder; PDP Display or on the remote control.
1. Connect an audio cable to the audio output port on the external device and [AV/COM- PONENT AUDIO IN[R-AUDIO-L]] port on the monitor, and connect the video output port on the external device to the [AV IN [VIDEO]] port on the monitor. 2. Play the DVD, VCR or Camcorder with a DVD disc or tape inser...
Page 35 - Connecting Using a HDMI Cable; PDP Display using an HDMI cable.; Connecting Using a DVI to HDMI Cable; the PDP Display using a DVI to HDMI cable.
Connecting Using a HDMI Cable 1. Connect input devices such as a Blu-Ray/DVD player to the [HDMI IN] terminal of the PDP Display using an HDMI cable. 2. Select HDMI using the SOURCE button on the front of the PDP Display or on the remote control. Note In HDMI mode, only PCM format audio is supported...
Page 36 - Connecting a DVD Player
2. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the [DVI / RGB AUDIO IN] terminal of the PDP Display. 3. Select HDMI using the SOURCE button on the front of the PDP Display...
Page 37 - Connecting to an Audio System
Connecting a DTV Set Top (Cable/Satellite) Box 1. Connect a Component cable between the [BNC/COMPONENT IN [R/P R , G/Y, B/P B ]] port on the PDP Display and the P R , Y, P B jacks on the Set Top Box. 2. Connect a set of audio cables between the [AV COMPONENT AUDIO IN [R-AUDIO-L]] on the PDP Display ...
Page 38 - Using the Software; MDC
Using the Software MDC Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the Serial MDC installation program. Note If the screen for installing the software does not appear, install it using the Serial MDC execution file in the MDC folder of the CD-ROM. 3. If the installatio...
Page 39 - Installation Problems; the network environment.; Uninstall; the Windows
Installation Problems The installation of MDC can be affected by such factors as the video card, motherboard and the network environment. Uninstall The MDC program can be removed only by using the "Add or Remove Programs" option of the Windows ® Control Panel. Perform the following steps rem...
Page 40 - Main Screen
Introduction A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cable should be connected between the...
Page 42 - Port Selection
14. Switches the OSD function On/Off. - May not be supported depending on the product. <Note> The remote control Enable/Disable function operates whether or not the power is On/Off, and this applies to all displays connected to the MDC. However, regardless of the status at the time the MDC is ...
Page 45 - Input Source
1) Source OSD - Sets whether the Source OSD will be displayed to indicate when the Source is changed. 2) Not Optimum Mode OSD - Sets whether the Optimum Mode OSD will be displayed to indicate if the current mode is not supported. 3) No Signal OSD - Sets whether the No Signal OSD will be displayed to...
Page 47 - Image Size
- Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV. 5) DTV - Changes the Input Source of the selec...
Page 49 - Time
Info Grid shows some basic information necessary to Image Size Control. 1) To adjust Image Size in TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV mode, click the Video Source tab. Select the display you want to adjust by using the Select button or by checking the checkbox. 2) Info Grid displays onl...
Page 52 - PIP
1) Specifies the date.2) Delete All - Deletes all of the holidays. 3) Add - Adds the specified date. 4) - Deletes the schedule in the selected line. The Holiday Management function can be turned on or off in the Timer setup menu. The Input source of MagicInfo works only on MagicInfo model. The Input...
Page 55 - Settings
Settings Picture 1. Click Settings of the main icons and the Settings Control screen appears. Basic information required to adjust the Picture is displayed in the main menu. Settings for the selected monitor will be displayed if one of the connected monitors is selected, and the default settings wil...
Page 59 - Maintenance
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adju...
Page 64 - Troubleshooting; Settings Value Display In Multiple Display Mode
The Input source of TV works only on TV model. The Maintenance Control function is available only for the displays where the power status is ON. Troubleshooting 1. The display you wish to control does not appear on the Power Control Info Grid - Check the connection of RS232C. (Check if it is properl...
Page 65 - Adjusting the PDP Display; Input
Adjusting the PDP Display Input Available Modes • PC / DVI / BNC • AV • HDMI • MagicInfo • Component Note • MagicInfo can only be enabled when a network box is connected. • The HDMI port and network box cannot be connected at the same time. Source List MENU → ENTER → → ENTER → → , → ENTER Use to sel...
Page 71 - Signal Control
Selects either On or Off with the signal Balance. Signal Control MENU → → ENTER → → → → → → → → ENTER → → → ENTER → 1. R-Gain MENU → → ENTER → → → → → → → → ENTER → → → ENTER → → ENTER → → , → ENTER 2. G-Gain MENU → → ENTER → → → → → → → → ENTER → → → ENTER → → → ENTER → → , → ENTER 3. B-Gain MENU →...
Page 75 - Size
Note This function is only enabled if the Color Tone is set to Off. Size MENU → → ENTER → → → → → → ENTER → → , → ENTER The Size can be switched. 1. 16:9 - Sets the picture to 16:9 wide mode. 2. Zoom 1 - Magnifies the size of the picture on the screen. 3. Zoom 2 - Magnifies the size of the picture m...
Page 94 - MagicInfo
• For MagicInfo in Device mode, moving external devices while booting may cause errors. Set up external devices only if the PDP Display turns on. • Do not unplug the LAN cable used for the network (ex: video display). Otherwise, the program (MagicInfo) may stop. If you do unplug the cable, restart t...
Page 98 - Self-Test Feature Check
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the PDP Display. 2. Unplug the video cable from the back ...
Page 100 - Problems related to the Screen
A: Check if the signal cable between the computer and the PDP Display is securely con- nected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the PDP Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ens...
Page 104 - Specifications; General
Specifications General GeneralModel Name SyncMaster P50HP, P50HP-2 SyncMaster P63FP, P63FP-2 PDP PanelSize SyncMaster P50HP, P50HP-2 50 " Diagonal (126 cm) SyncMaster P63FP, P63FP-2 63 " Diagonal (160 cm) Display area SyncMaster P50HP, P50HP-2 1105.65 mm (H) X 622.08 mm (V) SyncMaster P63FP,...
Page 108 - Information; For Better Display; automatic adjustment, use the Fine/Coarse adjustment function.; PRODUCT INFORMATION (Image Retention Free); What is Image Retention ?; PDP panel is operated for a long time with a fixed pattern .
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for PDP. • Resolution: 1360 x 768(...
Page 111 - Apply the Screen Erasing function on Product; • Apply the Screen Erasing function
Note ( Please check CD's User Guide at "OSD Function", some model's will not availa- ble. ) Apply the Screen Erasing function on Product • Apply the Screen Erasing function - Symptom: 2 Vertical blocks move with erasing the display Note ( Please check CD's User Guide at "OSD Function"...
Page 112 - Appendix; Contact SAMSUNG WORLDWIDE
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com MEXICO 01-800-SAMSUNG ...
Page 114 - Terms
Asia Pacific AUSTRALIA 1300 362 603 http://www.samsung.com CHINA 400-810-5858 010-6475 1880 http://www.samsung.com HONG KONG (852) 3698 - 4698 http://www.samsung.com/hk http://www.samsung.com/ hk_en/ INDIA 3030 8282 1800 110011 1800 3000 8282 1800 266 8282 http://www.samsung.com INDONESIA 0800-112-8...
Page 115 - Correct Disposal
Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The fre- quency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per sec- ond, this ...
Page 116 - Authority; Information in this document is subject to change without notice.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Eu- rope only from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their...
